Having problems with your Dyson Ball DC24 Bagless Upright Vacuum ?
Rug brush bar does not work
\015 When I press the button on the brush bar alternative(to clean rugs) nothing happens. The vacuum continues in the wood floor mode.\015
Repair Help & Product Troubleshooting for Dyson Ball DC24 Bagless Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Rug brush bar does not work
... Dyson Ball DC24 Bagless Upright Vacuum
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
My bissell pro heat carpet cleaner is not working properly...the scrubby bar is not turning... the belt is intact and working and it is turning the knob inside but the brush bar does not turn
How are the bearings? Maybe the motor that drives the belt is burnt out. ... Vacuums
My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.
Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum
I have a dyson dc14 how do i repair my vacum? i need to try to replace the brush bar motor or something so that i can get the brush bar to work again.i hope you can help me out
Brushbar not spinning:--\015\012Ensure brush control is set on carpets mode. Note: brushbar will only spin when\015\012the handle is reclined.\015\012To get user manual for your vacuum please click on the link mentioned below\015\012 ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
Beater bar brush stopped working...
Does the power head motor stop, or does the brush roll stop. If it is the brush roll stopping, replace the belt and/or the brush roll. If it is the motor, you may need to clean out around the motor, it may not be getting enough air to cool causing ... Rainbow E series Canister Wet/Dry Vacuum
Brush bar on Dyson DC19 doesn't work properly on carpet setting
Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.
If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
We have a kenmore canister vacuum and it runs but when turn on the rug clener brush the brush will not run we then put on small brush head and that will work
If the power head motor runs, but the brush doesn't turn, then the belt is broken. Replace the belt and it should work. ... Kenmore Vacuums
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums
My shark bagless sweeper worked for about 6 months. Like a previous blogger, I caught the edge of a rug that jammed the sweeper, three red lights blink, the brush is free moving yet the sweeper will not work. I did leave it plugged in all the time otherwise it would not run but for minutes. Very disappointed. New battery? what if that doesn't work? is it junk then, money down the drain.
This will probably cost you more to repair than to buy a new one. Does it turn on at all? ... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray
Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest
I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum
My dc-15 bush bar will not work - Dyson 909592-05 DC-15 Roller Brush Beater Bar
Head motor blown, will have to take it to your nearest good hoover repair centre should cost around 49 dyson will charge 73 ... Dyson 909592-05 DC-15 Roller Brush Beater Bar
The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.
Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum
My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!
... Kenmore 25512/ 25513 Progressive Canister Vacuum
My beater bar is not turning so the vaccuum is not picking up. The belt is not broken. The motor is working and I can see the cyclone effect in the canister. I have checked for blockages. I have cleaned the hair and string from the beater bar brushes. What should I do?
You need to replace the belt, it has probably broken. Your actually supposed to change them yearly. Here is a link to\015\012the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My brush bar won't turn - works in bare floor mode, but carpet brush won't turn when it should...
Replace the belt the belt sounds like its worn or stretched the belts turn at high rpms and get very hot and soon just ware out they work fine on floors but when it comes to carpet they slow down, i hope this works out thanks ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Dyson dc15 bagless upright. my brush bar is not working but if you use the hose it works .
\015\012http://www.espares.co.uk/datastore/ProductManuals/350256.pdf\015\012\015\012Check the above link to see if it h ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum
The motor that powers the brush the brush that beats the rug has a sparking in it ( it works but this does not appear good)
You will see sparks all the time around the brushs if it is working and if the sparks do not go all the around the comutaor\015\012it will be fine ... Fantom Vacums Lighting Canister Vacuum
Brush bar won't work
The belt is usually attached to its own motor. Have you checked that the electrical plug for the motor to the electronic board is not loose? If that is okay, does the brush spin on its own when the belt is detached? If not there may be hair or fi ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I just bought a dirt devil, started to vaccum got caught on a rug, and now the beater bar isnt working
... Dirt Devil Vacuums
Rug doctor brush not working
MY vaccuum wont suction or turn at the brush bar. The wand works and I already checked/cleaned all the areas the instrucion manual said to.
The DC07 has a "brush control system" operated by a knob on the right side of the base. This knob has two positions: "bare floors" (or "off") and "carpet" (or "auto"). The roller will turn only when the knob is on "carpet", and even then only w ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Bissell pro heat carpet cleaner, won't move forward. both belts working. is there something that is suppossed to hold the brush bar down so the carpet cleaner uses that as it other set of "wheels"
... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bought clearance item Sunday just found out the brush bar was motorized it turms only when i move the vacum back and fourth it should turn on its own right ? I have very little suction from the bottom the hose works though
This appears to be a loose connection. The below post was answered by highntools a while ago. It probably is related to you problem. That is why moving it back and forth makes it go on.\015\012\015\012I have finally fixed my sister's d ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum