Having problems with your Dyson Ball DC24 Bagless Upright Vacuum ?

Dyson DC26 brush bar not rotating and ligths still flashing

\015 My Dyson DC26 brush bar does not rotate and the red and white lights are flashing. The brush bar was cleaned and still the unit does not work.\015

Answers :

Repair Help & Product Troubleshooting for Dyson Ball DC24 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson DC26 brush bar not rotating and ligths still flashing


... Dyson Ball DC24 Bagless Upright Vacuum

Dyson dc28 red and white lights keep flashing, brush bar does not rotate. Cleaned off bar and still the same problem


... Dyson DC28 Animal Bagless Upright Vacuum

I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.


I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum

Dyson dc25 brush bar not rotating


... Dyson Dc25 Cleaner Head Assembly

Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.


If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I have a dyson dc14. the brush bar will not rotate when the vacuum is running. the belt is attached and it will rotate by hand. when you switch from bare floors to carpet-the bar will not kick in and rotate.


\015\012Hi,\015\012Check that when you pull back handle to vacuum the clutch control knob which is located front lower left side of machine moves to drive position & is not stuck in off or park po ... Dyson Vacuums

Dyson dc14 brush bar is not turning at all. Everything else seems to be fine. I just replaced the brush bar but still no movement. What else could it be?


Hi there,I'm sorry to hear you're having difficulty with your DC14 Animal. If the brushbar doesn't rotate, please check you have the brush control set to 'Carpets', not 'Hard floors'. The brushbar will not rotate when the machine is standing ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have removed the obstructions in the brush bar and the brushes still will not rotate. What else can I check?


Hi Genie, it's Jack at Dyson.Once you've cleared any obstructions from around the brush bar and inside the cleaner head, you need to reset the machine. This is easy to do - just press the button in the red recess on the side of the cleaner he ... Dyson Ball DC24 Bagless Upright Vacuum

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.


... Dyson Vacuums

Cleaned the brush bar but still not spinning DC14 Dyson


The belt is broke. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson dc 07 brush will not rotate. I have cleaned all hair and debris from around the brush and no change. I can not even figure out how to look and see if the belt is still attached. Suggestions?


DC07s are not easy to check the belt on, in fact depending on which exact model you have there are probably two belts.\015\012One connects the output of the motor to the clutch mechanism (one end of which has the control knob that ... Dyson DC07 Bagless Upright Cyclonic Vacuum

DYSON DC14 While vacuuming the living room, the rotating brush started making an awful loud grinding sound. We opened the intake port, cleaned the brush but to no avail sound still persists once you lower the vacuum handle in an attempt to clean. Was wondering if there was anything that can be done?


Take the bottom plate off and check the belt. Also, rotate the brush by hand - it should turn with only a moderate resistance from the belt, or very little if you take the belt off. If it is hard to turn, or if the belt is stripped-out right where it ... Vacuums

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?


I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

The brush head on our Dyson DC34 rotates for a second and then stops even tho vacuun still operating - how to fix?


... Dyson Dc34 Animal Handheld Vacuum With Longer Run Time For Pet Owners

I havethe first generation purple Dyson Animal model. The brush rotates fine, but doesn't make sufficient contact with the floor/carpet, therefore does not pick up most items on carpets (suction still works however). If I put my foot on it and push down a little, it works. However, since I'm not an accomplished acrobat, this is not easy to do. :-) Any suggestions on whether this is fixable? Or should I just save up to buy a new one?


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 switched off whilst hoovering, It would not turn on, 1st it stopped rotating brush and than tuned off completly.. I tried ttoi change the fuse but still not turn on. Motor not runnung either.


Hi its Darran at Dyson.Our machines are fitted with a thermal cutout switch. This will activate if the motor on your machine becomes too hot. This is caused by a lack of airflow to the motor, which is caused by a dirty filter or a blockag ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson vacuum brush bar will not rotate and the belt is not broke. The hand tool works fine. What is wrong?


I took the plate off and cleaned up the vacuum brush bar. Since the belt was not broke I knew that was not the problem. I know when the setting is bare floor, the brush bar will not rotate. That was not the problem. I just keep turning the knob f ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Hi my dyson dc07 animal has suction but the brush bar wont turn. If I turn it on there is a horrible noise. The belt is still fine


The belt is probably worn or stretched. When this happens the belt won't turn\015\012the roller brush when it is against the carpet. Here is a link for the\015\012manual and links for the belt ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brush will not rotate but still has suction - Dyson DC07 Bagless Upright Cyclonic Vacuum


Hi there,Sorry to hear you're having difficulties with your DC14. Please note, the brushbar will never rotate when the cleaner is standing in the upright position, or if you have the brush control set to 'Hard floors'.However, ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush bar won't turn - Dyson DC26 Bagless Canister Cyclonic Vacuum


... Dyson DC26 Bagless Canister Cyclonic Vacuum

The brush bar on my Dyson DC17 stopped turning.


If this model has a brush control - i.e a roller at the side of the model which controls brush to spin or not, then its a protected brush model - therefore even if the drive belt is intact the Dyson would have to be repaired by a service personnel or ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hi. I have a DC 24 which when brush rotates makes a very loud noise. I have replaced the brush and side bar. The side bar appears very loose. The noise stops when I switch the brush rotation off. Any ideas ?


Hi there,I'm sorry to hear you're having difficulties with your DC24. If the cleaner head seems to be making an unusual noise during use, you may want to check all the parts are correctly assembled, and that the cleaner head and brushbar are ... Dyson Ball DC24 Bagless Upright Vacuum

Dyson DC14 Brush Bar won't turn


You don't need to take it for repairs, I just corrected the same problem on the phone with a tech. Have the head on your lap, make sure the end nearest the little belt has the rounded side of the bar facing you. The squared off end faces towards th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Motorized brush bar not turning on Dyson Vacuum


Apparent common failure is that either the thin yellow and or blue motor drive wires that run from the LH side of the vacuum where the "control board" is located down into the hinge / ball area become stretched and then fray and eventually break. Ha ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0992 seconds