Having problems with your Dyson Ball DC24 Bagless Upright Vacuum ?

Remove screws hoover

\015 I need to cut a piece of lead away that goes into the appliance and then replace the shortened lead. I can not undo the 3 screws that secure the lead into the appliance.\015

Answers :

Repair Help & Product Troubleshooting for Dyson Ball DC24 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks


HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dismantle hoover sc211 . The auto cable rewind does not work and I need to split the machine. I have removed alll visible screws, but there must be some hidden screws at the switch end>


... Hoover Vacuums

Hoover Alpina 2 1300 cleaner. I need to split the upper and lower casings to check that the switch is working. I have removed the screwa in the area around the bag, but now need to remove the switch and cable rewind covers, as I assume there are more securing screws under them. Can you advise how to do it please?


Move covers (forcibly !) away from the centreline of cleaner then move to rear until released. The covers are held by slide catches on inner edges. ... Vacuums

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Remove screws hoover


... Dyson Ball DC24 Bagless Upright Vacuum

I need to open up this Hoover Uprite Runabout deluxe to replace the belt. I dont see any screws to remove to access. Model # U5064-940


You will find them on the bottom of the machine on the brush roll cover. This is the belt you need:Hoover Runabout Deluxe U5064-940 Belt ... Vacuums

Hoover Windtunnel We bought a new power cord because our's broke. We cannot figure out how to uninstall the old one and reinstall. My husband has removed just about all of the screws.


If it goes in just at the bottom of the handle, take off the handle, then remove the tool holder, then you can replace the cord. If it goes in near the bottom, then you will have to remove the motor cover and light to get to the connecting wires. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Smoke from Hoover Savvy U8185-900. Looks to be from the Motor assembly U8174-900. How to access motor in order to verify condition, have already removed all screws, but unabale to expoxe motor..


... Hoover U8185-900 Upright Vacuum

Hoover windtunnel vaccum U6445-900 motor not turning on. I removed the screws and located the contacts inside. There is an on-off switch which seems to be stuck Is there a way to replace this switch


There are a number of Hoover vacuums that are subject to a recall due to an overheating on/off switch. Check out this web site to see if your is included. You'll need the model number and serial number from the back of the unit. The manufacturer w ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

I have a small canister type hoover vacuum and I would like to open it because the cord rewinder it jammed. I have removed all 4 screws but still can't seem to separate the two pieces. Am I missing something?


I may be able to help, but would need to know what model your machine is. Re-post, giving as much detail as possible and we'll see... ... Hoover S3330 / S3332 Straight Suction Telios Bagged Canister Vacuum

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]


... Miele Vacuums

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How do you remove the Handle from the Hoover Windtunnel Deluxe to replace the switch?


Removing the handle assembly should be easy after removal of the two screws. It may be binding or hanging up on the self-propel cable...or the plastic may just be stuck/binding. Note that the handle slides in and out of the vacuum unit along the sa ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I have a Kenmore Progressive Canister Model # 29612992. I was replacing the sweeper bag, when I opened the lip, the plastic arms was pull out of joint and will not close. I removed the 2 screws under the lid to put back it in place but there I can't remove the plastic molding because there are still screws holding somewhere. Are there tabs instead of screws still hold the molding?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

I am trying to replace the belt on my bissell. The directions state "remove the screw that holds the red retainer in place, set red retainer arm and screw aside. I see the red retainer but can not get it out I also can not remove the black brush arm that holds the brush in place. I have tried and can not remove it.


Hi, Did you release the handle first before you flipped it over?Have you removed the screw and it still won't come out, or is it stuck even after the screw is out?Are you having trouble getting to it?Please r ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

How do I replace the motor brushes in my DC11? I cannot dismantle beyond removing the pipe attachment. I've removed the 6 fixing screws that are visible, but the machine is still firmly "together" as if there are still screws that I've not located. Does it snap apart? Are there hidden screws? Paul


You can buy brushes but if the armature is overheating changing the brushes wont help ... Dyson Vacuums

Removing handle of Hoover Widepath Floormate Spin-Scrub


... Vacuums

I have a Honeywell HF810 fan. I am trying to clean it. I removed the phillips head screws, but their are two odd screws that require a special tool to remove them . I also have to go through the plastic shaft, so I need a special type of screwdriver and a special type of head. Thanks for the challenge!!


... Honeywell Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0621 seconds