Having problems with your Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow ?

DC15 Vac comes on but the head will nmot come on. Local Vac shop said circuit board was burn up,can I repair myself. where do I get parts


Answers :

HighnTools had posted this solution - try it.\015\012
\015\012I \015\012have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires \015\012connect to circuit board lead to the beater bar. The wires broke where \015\012they go through the black rubber gommet. You need a torx screwdriver tx 15 to \015\012remove 2 plastic covers to access the wires. When looking at the front of the \015\012vacuum, the gray covers located on the right side of the vacuum. 1 big cover \015\012with a black rubber gasket and other small gray cover is on the rotating ball \015\012area.
\015\012
\015\012I hope this solves your problem.
Repair Help & Product Troubleshooting for Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

DC15 Vac comes on but the head will nmot come on. Local Vac shop said circuit board was burn up,can I repair myself. where do I get parts


HighnTools had posted this solution - try it.\015\012\015\012I \015\012have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires \015\012connect to circuit board lead to the beater bar ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

I have owned 4 sebo uprite vacs. Every one of them has the same problem. Where the handle connects to the vac it break contact and shuts off and on. It seems the connection between these two parts is very weak. The only answer I get from my local repair shop is


Well you now know the error of your ways, don't buy another!The best fix is to remove the connectors and connect the wires directly together. ... Century 400 UVAC Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Getting part My repair shop cannot get the part for my filter queen. It's the plug in the body of the machine that the short plug goes in from the hose. It's been bent. Can I get a replacement part?


Have you called your filter queen dealer? i used to be a rep. and we would fix problems at the office that i worked out of. hope this helps. ... Filter Queen Majestic Canister Vacuum

I have an Eureka Express canister vacuum - I believe it's model 8284 - that just stopped working. Plug it in, turn it on, and absolutely nothing happens. I took it to the local sew and vac place and they say it's a circuit board that is no longer available. I've looked at all the parts lists and diagrams for that vacuum and I would swear there isn't a circuit board there. (I wouldn't have even thought that in 1989 they would have used circuits.) In any case, I absolutely love this machine a


Given the age of the machine weighed against you fondness for it, unless you can find a fault with either the switch or the cord, there is little else that can be done. With time the electrical lead can break down and one o ... Electrolux Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

I have a riccar 500 upright and the axel broke in half. The repair shop says it cannot be repaired without replacing the part. WHere can I get the replacement part?


The repair shop should have all the parts needed. However, sometimes the manufacturer stops making some parts. If this is the case, you may need to try to find one at a thrift store or garage sale and cannibalize it. ... Riccar 8955 Upright Vacuum

The repair shop told me my Oxygen3 needs to have a sumo(?) board replaced...again. I am not willing to pay for another repair and am wondering whether an new hose and adjustable extension tube would solve the recurring problem. Is the sumo board located in those parts or is it a malfunction that transfers to somewhere in the canister?


The Sumo Board, is housed inside the canister section, part # and discription below\015\012E-1180136-56 SUMO BOARD\015\012So replacing the hose and or wand will not fix the problem. Suggest you stay away from "big box", retail, discount s ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My shop vac blows dust as soon as it's turned on and throughout use. I have changed filters, nothing is helping. What part of my vac can not get wet, or is there a better way to clean out the system?


There should be a cover or sock over the filter,this will stop the dust.the paper filter is the part that can not get wet. if you don't have a cover for your filter use an old sock or something simular to a sock. ... Shop Vac 584-04-00 Quiet Canister Wet/Dry Vacuum

We have an Ebac Homedry 660 dehumidifier. It makes a noise when started and the red light indicating water tank full comes on. It has been inspected by a local repair shop and we have been told that the 'Fan' is not working. The workshop does not know how to get a spare part. Who is the repair agent in Auckland, New Zealand?


... Vacuums

I have a old Shop-vac Stainless Tank QSP CONTRACTOR Wet/Dry Vac Model QPL625 Original #52722-67 Motor arcing and locking up can I get replacement parts?


You can get new motor off the link belowhttp://www.shopvac.com/shopvac-accessories/Departments/Repla ... Vacuums

I have a QSP Shop Vac 4 Gal and the motor has burned out. Can I get a replacement motor. These are some of the numbers on a label stuck to the motor FMC 01(F), FMC 02, 82122180, 27801 20 Thanks Carl Armstrong


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

I have a dewalt cordless/corded shop vac and it works fine with a new battery installed. When I plug it in it does not work. I took it apart and saw that the cord goes straight to a circuit board and is beyond me to troubleshoot. Has anyone had this problem before?


... Dewalt DC500 Canister Wet/Dry Vacuum

I have a series 90 L - wet/dry shop vac and the caster feet are broke on it can I replace them? If I can where can get the parts from?


... Vacuums

Problem: water will not dispense Local repair shop gave verbal diagosis>need both solenoid valves. Found this part on www.nelsonappliance.com $14.95 each. (Shop quoted $98 for repair & parts) Can i access & replace parts? Is there a "how to" video available?


... Bissell 9200 Upright Vacuum

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray


This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

Brand new 3HP shop vac smells like motor burning when turned on!


... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum

Parts for a craftsman shop vac


Hello. The best source of craftsman parts is sears.com\015\012\015\012If they don't have these parts I will be very surprised. regards, Joe ... Vacuums

I have an old Shop Vac model 3331.5. This is a 12 gallon 1.5 hight peak shop vac with a detachable blower. After many years I decided to use the blower feature, but have lost the lost the manual. Question; how do I attach the hoses to the blower? The motor has that cap on it the direct the flow of air in one direction and the wide hoses do not fit over it. I may be missing a part, but I would think the directional cap would have to come off anyway.


Remove the cap that directs the air and insert the hose in there. ... Vacuums

Repair manual for shop vac 87719-17 - Shop Vac Vacuums


... Shop Vac Vacuums

We have a Singer 626 sewing machine. It's an old mechanical machine with heavy metal parts. The stitch selector was stuck, I removed the top and helped the selector to move. when I had to move the selector again, it was stuck and I pushed too hard and broke a component. I can fix the machine if I had a repair manual. I need to buy a repair manual. How and where can I get one? Thankjs Charlie PS. Im pretty mechanicly inclined and I was able to clean the machine and get it to work after


... Vacuums

Miele seb 213 Powerhead is getting ac power but there is no power to the motor. The light comes on and I get 120V on the ac side of the circuit board with a meter but zero volts on the dc side.can I replace the board or do I have to replace the whole Powerhead?


... Miele SEB 213-2 Vacuum

Shop vac circuit breaker location - Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum


... Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Lost Part I have a 6.5 hp 18 gallon shop vac ultra pro. There is a part that goes into the inside of the tank and screws into the collection hose that attaches it to the tank. This part accidentally got thrown away when someone dumped it and now I cannot attach the hose to use the vacuum. Can this part be purchased separately?


I found a manual online for the shop vac and found the part number. Did locate part online.\015\012Thanks, ... Shop Vac Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0711 seconds