Having problems with your Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow ?

Dyson ball does not switch to carpet

\015 When you press the switch to go from floor to carpet, it will no longer to to carpet. It stays on floor mode. The vacuum is about 3 years old. Any solutions??\015

Answers :

Repair Help & Product Troubleshooting for Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson ball does not switch to carpet

... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?

Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The brush on my dyson ( for carpet) quit working. the belt is fine just won't turn on when I switch it carpet. Any suggestins?

... Dyson DC14 Bagless Upright Cyclonic Vacuum

My Dyson DC15 has suddenly become very reluctant to turn left. This is only the case when it is switched on and irrespective of whether the roller brush is running or not. When the cleaner is switched off it behaves as normal as far as steering is concerned.There is no obvious problem with the ball or steering swivel mechanism. Any ideas ?

Hi its Darran at Dyson. Although strange, I believe we have a solution. It sounds as though the cleaner head hose is blocked. When the machine is running the suction will be pulling against the bloskage causingt he hose to contract and p ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Our vacuum will not stay running.. We have cleaned both filters several times since dyson told us there was a switch which turns the vacuum off if the filter in the ball was dirty, but we still need to keep pushing the switch several times to turn the unit back on while vacuuming.

... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson vacuum won't switch to carpet mode

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc15 ball turns when off but not when switched on

Hi John,I'm sorry to hear you're concerned about your DC15. When the machine is switched on, the powerful suction causes the soleplate to seal closely with the floor surface.This may be why the machine feels a little heavier to steer when the ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a brand new DC 24 (orange ball) Dyson. The brush is not turning and it is extremely hard to push on carpet. Something must not be engaged. What should I do?

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hello. I took the sole plate of to clean the brushes on my dyson dc14 however the brush part came out and i put it back in but since then whenever i switch it over to carpet setting it makes this really horrible clicking grinding sound its only new have only used it a couple of times.

You really need to take the sole plate back off and make sure the belt is running exactly where it's supposed to go and not looped over a piece of plastic or anything. More important is that you make sure the ends of the brush are seated properly an ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Brush does not rotate when switch is on - Dyson Ball DC24 Bagless Upright Vacuum

Hi, mine did the same thing last week. I took off the end cap that holds the brush in place, and noticed inside the cap a piece was broken. Got a new end cap from Dyson, and it works fine now. Also, roller will not work in the upright position. You s ... Dyson Ball DC24 Bagless Upright Vacuum

My Dyson DC 15 makes a horrible noise when switched to do carpets - sounds like gravel in the motor - and then comes the burning smell. Nothing keeping the brushes from moving, and I think they are. I am concerned that it is a belt or the motor. How do I know?

... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a dyson 07. Vacuum works fine, great suction using the hose. How do I switch to using the carpet vacuum. (I lost my instruction book) Thanks

If this unit has a suction hose built in to the handle, the carpet vacuum should start working after you return the handle hose to the proper position. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The carpet brush on my DC25 Dyson Ball Animal has stopped working. Is there a reset button ?

Next to the power switch is another button, this switches the brushbar on and off. The brushbar can be turned off for hard floor surfaces so as not to scratch them ... Dyson Ball DC24 Bagless Upright Vacuum

I have a dyson dc14. the brush bar will not rotate when the vacuum is running. the belt is attached and it will rotate by hand. when you switch from bare floors to carpet-the bar will not kick in and rotate.

\015\012Hi,\015\012Check that when you pull back handle to vacuum the clutch control knob which is located front lower left side of machine moves to drive position & is not stuck in off or park po ... Dyson Vacuums

I cleaned out my dyson ball as it smelt when i hoovered, cleaned filters, washed out canister and took the screws out of the front bar so i could clean near the brushes.. now its making a high pitched noise and when i switch it off it makes a noise like an engine shutting down! Have i disturbed the motor?

Hi its Darran at Dyson. The screws on the base of the cleaner head should not have to be removed to access the brush bar so it is possible that the brush bar has come out of alignment, hence the noise the machnie is making. Pl ... Dyson Ball DC24 Bagless Upright Vacuum

My Dyson ball DC 24 power head (on/off switch) not working?

... Dyson Ball DC24 Bagless Upright Vacuum

My Dyson DC07 won't switch from bare floor to carpet mode. What should I do?

Hi its Darran at Dyson.Its worth moving the brush control dial from the bare floors position to the middle position a few times incase the dial has simply become stiff. If this does not resolve the issue, you may need an engin ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I had used Dyson DC08 to **** out a wet car carpet. A few days later when using the V/C, there was a burning smell. Subsequently I washed the flexible hose, changed the pre-filter and post filter , but I wrongly put the pre-filter in the spot for the post filter. When the V/C was next used, there was again a burning smell and sparks. The filters were switched, but the V/C would not re-start. What shall I do?

Hi there,We'd strongly recommend against using your Dyson to pick up water. If you haven't already got in contact with us directly, I'd encourage you to do so. One of our experts will be happy to recommend the best course of action. You c ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

The switch on the Dyson is stuck on the hard floor setting and so I can't use it for carpets

... Dyson Ball DC24 Bagless Upright Vacuum

Dyson ball not picking up when using in upright position. I can see the roller is stuck, with carpet twine, how do I open up the case?

Look at the endcaps of the brush nozzle there will be two plastic screws to unlock them, they rotate off. the brushrolls should pull out. what is the model #? ... Vacuums

I was cleaning the carpet and all of a sudden the motor stoped . I have power at the switch but the moter dose not rwork. I have the vaccum just nabout a year it is a dyson airmusale. Thank you [email protected] James Clark

Are you sure that something didn't get in the beater brush and is blocking it from turning? Does the vacuum ****?What was the last thing that happened when it started not working?more details?Best regar ... Dyson Vacuums

Dyson ball brush bar is not touching carpet

Hi there,I'm sorry to hear you're having difficulties with your DC24. If a part of the cleaner head assembly appears to be loose, I'd encourage you to get in touch with us directly so we can help. You can reach us on 0800 298 0298 (UK), or 1- ... Dyson Ball DC24 Bagless Upright Vacuum

I have an animal dyson. The front nose dives into the carpet when moving the dyson in the forward motion, fine when pulling back. A huge amount of effort is required to move it forward. Took it to a technician and he said he could find nothing wrong. He had only short nap carpet for test. Works fine on short nap, if the carpet nap has any lenght to it like shag, the dyson severly nose dives. It's like the nose is sucked into the carpet. This problem just occured after the wife used the ho

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson DC 25 Ball - no power to motor

Same problem here. We noticed a loss of suction for about 5 minutes and the suction stopped. Beater bar still rotates but ZERO suction. ... Dyson DC25 All Floors Bagless Upright Vacuum

Older dyson dc 14 control knob for swithing from carpet to floor

Most likely you need to replace the clutch assembly. This video will show you how to replace it. \012\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0476 seconds