Having problems with your Dyson DC03 Bagless Upright Cyclonic Vacuum ?
No drive to brush bar on Dyson DC 03
\015 Cleared the brush bar of accumulated long hair/fibres etc - all went back OK as before, belt seems fine, motor running, getting usual suction through accessories wand. Have tried the "rotate 5 times" routine described on the site - no joy on this occasion . . .\015
Repair Help & Product Troubleshooting for Dyson DC03 Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
No drive to brush bar on Dyson DC 03
... Dyson DC03 Bagless Upright Cyclonic Vacuum
There is a high pitches nosie coming from my dyson. It mainly happens when the flooring type changes whilst hoovering. Everything else is ok. It sounds to me like the drive belt for the brush bar or could it be the clutch. Hoover is over 10yrs old but is in good order and well looked after, this is really the first thing that has ever gone wrong with it.
... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
Dyson dc28 red and white lights keep flashing, brush bar does not rotate. Cleaned off bar and still the same problem
... Dyson DC28 Animal Bagless Upright Vacuum
I have a dyson dc14 how do i repair my vacum? i need to try to replace the brush bar motor or something so that i can get the brush bar to work again.i hope you can help me out
Brushbar not spinning:--\015\012Ensure brush control is set on carpets mode. Note: brushbar will only spin when\015\012the handle is reclined.\015\012To get user manual for your vacuum please click on the link mentioned below\015\012 ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
My dyson C07 ANIMAL is making a loud clatter noise when I push the head down. I have removed the sole plate and the brush bar is cracked so I removed it, but I understand the clutch maybe a problem also from reading other people's comments..how can I tell if it's a clutch problem also? Or... could it be just the brush bar being cracked that's causing the loud noise?
... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
The bar brush does not spin. I opened the vacuum head and the drive belt to the bar brush is loose. I don't see how you remove the slack from the belt.
You have to have it in the carpet setting in order to put pressure on the v-belt. there is no way to tighten up the v-belt, but i would try to replace the big flat belt. if you haven't changed this belt in over 6 months, i would change it. ( on avera ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Dyson dc14 brush bar is not turning at all. Everything else seems to be fine. I just replaced the brush bar but still no movement. What else could it be?
Hi there,I'm sorry to hear you're having difficulty with your DC14 Animal. If the brushbar doesn't rotate, please check you have the brush control set to 'Carpets', not 'Hard floors'. The brushbar will not rotate when the machine is standing ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.
The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The brush bar on my Dyson DC17 stopped turning.
If this model has a brush control - i.e a roller at the side of the model which controls brush to spin or not, then its a protected brush model - therefore even if the drive belt is intact the Dyson would have to be repaired by a service personnel or ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Dyson DC14 Brush Bar won't turn
You don't need to take it for repairs, I just corrected the same problem on the phone with a tech. Have the head on your lap, make sure the end nearest the little belt has the rounded side of the bar facing you. The squared off end faces towards th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.
... Dyson Vacuums
Dyson DC26 brush bar not rotating and ligths still flashing
... Dyson Ball DC24 Bagless Upright Vacuum
Motorized brush bar not turning on Dyson Vacuum
Apparent common failure is that either the thin yellow and or blue motor drive wires that run from the LH side of the vacuum where the "control board" is located down into the hinge / ball area become stretched and then fray and eventually break. Ha ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.
If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
Dyson DC 28 brush bar wont spin
... Dyson DC28 Animal Upright Vacuum New DC 28 Animal
Brush bar on Dyson DC19 doesn't work properly on carpet setting
Dyson DC25 Broken Brush Bar Connector
Hi Alex, it's Jack at Dyson.I'm sorry to hear you're having difficulty with your DC25. If the drive spindle of your machine has broken in use, you would need to replace the cleaner head assembly.Please get in touch with us directly, a ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
Dyson Animal DC 28 brush bar removal
Hi there, it's Jack at Dyson.I'm sorry to hear you're having difficulty with your DC28's brush bar. I've attached our video which shows the correct way to remove any obstructions and reset the machine, in case this is useful to you.Th ... Dyson DC28 Animal Bagless Upright Vacuum
Dyson dc 15 brush bar motor - reassemble
... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
The brush bar wont spin on my dyson dc 25... i
Hi its Darran at Dyson.Simply switch the machine off and stand it upright. Press the brush bar on/off switch once and then turn the machine back on. When you release the machine into the vacuuming position, the brush bar shoul ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow
Brush bar on Dyson DC07 clic
Not sure if I understand what you mean, but I'll try... I guess the "button" that you refer to is the clutch knob that's located on the side of the base. It has three positions: manual off, auto off and auto on. In manual off, the brush bar is always ... Vacuums
Dyson dc25 brush bar not rotating
... Dyson Dc25 Cleaner Head Assembly
Cleaned the brush bar but still not spinning DC14 Dyson
The belt is broke. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dyson dc 33 brush bar not spinning - Dyson DC33 Bagged Upright Vacuum
... Dyson DC33 Bagged Upright Vacuum
My brush bar wont engage on my dyson DC39 - Dyson Vacuums
Contact Dyson regarding the fault.\012There is a 5 year warranty on parts their customer service is amazing . They may send you a part to fit if faulty . ... Dyson Vacuums