Having problems with your Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum ?

Very loud clicking noise and I am stuck trying to take it apart

Answers :

Repair Help & Product Troubleshooting for Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Very loud clicking noise and I am stuck trying to take it apart

Have a look at:\012\012http://www.dysonmedic.com/DC04%20Folder/DC04%20page.html ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

I bought the Eureka 4703D model vacuum and my very first time powering it on, it was extremely loud - abnormally loud, and I don't know if it is loud like that because I possibly put it together wrong, or there is something wrong with it or it was previously damaged and I would like to know if this is something I can fix myself or do I have to take it back apart and return it to Walmart where I purchased it from. When it makes the loud noise, it does vacuum fine but the noise is just unbearable

... Eureka Power Plus 4703D Bagless Upright Vacuum

A baby sock was sucked up and stuck where i can't see it in my regina electrikbroom cleaner - 11.4 amp. i have tried to get it out and now i have to take it apart i think and can't get the housing apart - what should i do?

... Regina ElectrikBroom RG100 Vacuum

DC28 Clutch DC 28 Clutch made knocking noise after about 1 hr of use. Tried to take it apart and see it it had an obstruction but burned up the belt and damaged clutch. Yes, I know I should heave taken to the dealer or warranty service but thought it was something simple. Nothing inside is simple on a Dyson! Can the clutch be replaced and from what vendor?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My roomba 550 makes loud clicking noises and stops after 5 minutes and tells me to check brushes. I have taken it apart as much as possible and cannot find the problem

Pull brush rollers out.pull funny lookin yellow ends off and clean hair ect.out .also pop out front wheel and clean ... iRobot Roomba 550 Vacuum

I bought this vaccuum just a few months ago. Now it barely sucks anything up and it is making this very loud noise. It almost sounds like the brush is going to vibrate off. I keep thinking something is stuck in it, but I took it apart and everything seems normal. It did melt a couple of belts also.

Probably the motor is jammed or the part where it sucks up stuff its full ... Bissell 3590 CleanView Bagless Upright Vacuum

Just bought this a month and a half ago - used 3 to 4 times and it is making a loud humming noise like something is stuck. Filter is still good and cup is cleaned each time. Wanting to take it back to store and exchange it.

Is there any thing caught in the roller brush? Carpet string, plant leaf,Coin?\015\012\015\012Try removing the suction hose and putting a broomstick through it to unclog any thing you may not be able to see.\015\012\015\012At ... Vacuums

My Bissell powerforce 6579-2 is making a loud noise and i want to repair it myself but i dont know how to take it apart?!

The loud noise is probably coming from the beater bar section of the vacum if you flip it over there is a cover thats held on by some philips head screws if you pull the cover off you will see the belt connected to the beater bar and the motor someth ... Bissell 6594 PowerForce Bagless Upright Vacuum

My vacuum is making a loud noise like I sucked up somehting I shouldn't have I have cleaned all the hair and made sure there was nothing else stuck in there but it continues to make that loud noise is there something else that will cause it to make this ugly noise, and how can I fix it

... Dyson DCO7 Upright Vacuum

My upright kenmore progressive vacuum will not suction up when using the sweeper. It will suction things when I use one of the tools. I have put in a new bag and have tried to see if anything is blocking the bottom. It sometimes makes a very loud noise when I try to vacuum. If I press the intell clean on and off yellow button the noise may go away but it still does not work.

Double check hose placement, making sure you have the hose inserted into the correct slot. The long attachment nozzle stores in the front hole on the right, and the sucking hose inserts into the rear hole on the right. I know this is too simple of a ... Vacuums

My Bissell Proheat 12 amp is hard to push forward(whether on or off). There is a loud clicking noise when pushing forward and it ''jumps'' up on every loud click. It's OK when pulling backwards, sprays and vacuums up water. Belt appears OK. Thanks

I had this same problem and here is what solved it for me. On a previous cleaning session, my wife decided to take the two front screws out of the clear plastic shroud that covers the brushes in order to clean behind it. Upon re-installation, she did ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Loud noise I have a brand new Dyson and it is great on all my floors except one of my area rugs when it starts making this really loud vibrating noise. I am not sure why - nothing is stuck in the roller or vacuum and it doesn't make it on any of my other rugs. Also it is really hard to push whereas all the other floors it just glides. I don't want to return it but I also don't want to hear this sound every time I vacuum.

This is the clutch as it jams up in the brush. Usually happens with rugs that are not secured to the floor. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My bissell momentum vacuum is making a very loud noise but it still picks everything up. Do you know of a reasons why it is making very loud noises. I checked and nothing is stuck in it.

It might be the motor or the fan is messed up.have someone or you check that out. ... Bissell Vacuums

Cable stuck in machine (sphera 20). How do I take apart to release cable please? I cannot see any visible screws to take the machine apart. Cable will not retract or come out of machine

... Bosch Vacuums

Makes a loud noise like a grinding noise then smokes comes out and it smells like burning rubber? When I take the (rod) brush off with the belt then run the vacuum there is no more noise? Please help me thank you

Your belt is worn and stretched and so it is slipping on the motor drive shaft. That is why it is noisy and smells like burning rubber. You simply need to replace the belt. You can get replacement belts here: ... Vacuums

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse

By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

HORRID NOISE I have took it all apart and thoroughly cleaned it. It is still picking up dirt etc. But the noise sounds like its taking off. It is not that old so can not be the engine my mother has one that she has had much longer and is fine she has also checked it it is out of guarantee but is working the noise is terrible. Can you help???

Hitake out the belt and brush. Switch on. If the noise has gone you know its the brush. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a model 6100 healthy home vacum. When it's turn on the motor make a very loud noise. I took it apart and blew some dust out of it. And it still make the noise.

Hi,\015\012Usually when a vacuum is making the loud noise it is because of a stoppage somewhere in the vacuum.\015\012To find the blockage some detective work will be needed.\015\012First off take off the hose at the closest point t ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?

Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums

I have a new Hoover BH50015 hand vac. The noise is terrible. It sounds like the bearing are bad. When you take off the cup and the filter and listen to the motor as it slows down after turning it off it definitely sounds like bad motor bearings. Hoover tells me the loud noise is normal. Can you help?

Yes the bearing is full of dust and dirt\015\012unscrew the housing and clean the bearing area and shaft\015\012then add a dap of Vaseline to the shaft and reassemble\015\012The shaft rides on a nylon bushing which acts like a beari ... Hoover BH50015 Bagless Handheld Cyclonic Vacuum

My brush roller stopped spinning so I had to take it off and clean out all the hair that had gotten wound around it. I replaces it and now it is make a lound noise, but only when the brush is on. Could it be the belt making such a loud sound? It wasn't making this noise before.

Could very well be the belt.\015\012When cleaning the brush it is a good idea to add some WD40 at the ends where the plastic pieces are that hold the brush in the vacuum. The brush needs to be able to move freely around the plastic pieces.\015\012Ad ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

My Jacuzzi Tracker 4x just "stopped"..there is a nice strong flow of water going into it, but the wheels just aren't turning. I've tried the following to no avail: 1. blocked suction for a few seconds underwater with my hand (this has worked in past) 2. try to move front wheels back and forth (but they won't budge...back wheels do move on track though) Should I start taking it apart?

... Vacuums

How do i take apart the dyson,Theyre is something stuck in the hose extension. Is theyre anyway to take it off. The bottom part works . however theyre is no scution threw the hose

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John

It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0708 seconds