Having problems with your Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum ?

There is a high pitches nosie coming from my dyson. It mainly happens when the flooring type changes whilst hoovering. Everything else is ok. It sounds to me like the drive belt for the brush bar or could it be the clutch. Hoover is over 10yrs old but is in good order and well looked after, this is really the first thing that has ever gone wrong with it.


Answers :

Repair Help & Product Troubleshooting for Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

There is a high pitches nosie coming from my dyson. It mainly happens when the flooring type changes whilst hoovering. Everything else is ok. It sounds to me like the drive belt for the brush bar or could it be the clutch. Hoover is over 10yrs old but is in good order and well looked after, this is really the first thing that has ever gone wrong with it.


... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

I have bought new Hoover bags on two occasions. The first spares I bought were the Xxxl variety and I didn't think they fitted that well. The next spares I bought were the type g megafilt. I still feel like they do not fit that well and the suction power on the vacuum is not as good. I'm I buying the correct replacements? I followed the guidelines on the Hoover bags the vacuum came with. These were printed as the right bags to buy. I only have the vacuum around a year and thought it was brillian


... Bosch BSG71310UC Bagged Canister Vacuum

I have a dyson dc07 with a malfuncitoning clutch diagnosed here on fixya. I've replaced the clutch and the grinding noise when the clutch is engaged for carpet and non rotating brush problem presists. This is after replacement of the clutch with a new part. Install of the new part went well and there are no otehr apparent problems with the unit. Ideas? The unit is only a couple years old and not used that much on carpet. For an expensive vacuum I'm not that impressed with it at this point.


Greetings from GoVacuum,\015\012\015\012If you have replaced the clutch already, then this can really only be one other problem, and that is the roller brush. If the roller brush's bearing have locked up, and the brush is no longer spinn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi The band snapped the other day on my Vax Swift Turbo upright hoover and i got a new band from a Hoover repair centre. (Im assuming the bloke sold me the correct band). Was tight to go on. And it seemed ok. However, after switching on the band snapped immediately. Kinda burnt as well (at the point it snapped). Any ideas as to what the problem is here? The hoover is roughly 2 years old and used around 3 times per week. thanks Mike


Sounds like the brush roll is bad. Did you check the ends to make sure they turn freely? If not, replace it. ... Vacuums

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

My Eureka/The Boss doesn't seem to have the suction power it had. However, when I place my hand under the hose, it has good suction, then when I try to pull in a small particle, it doesn't, unless I have the hose nozzle completely over the particle. The vac is 10 yrs. old. I cleaned everything. Someone said the belt. Would the belt matter if the hose doesn't **** well? It is just old and worn out? It did shut off recently do to overheating. Help. Thanks. Lorraine


Doesn't "The Boss" Vacuum have a filter? Perhaps your filter is clogged and not allowing it to work properly. ... Vacuums

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would


... Hoover L2310 GUV Central System Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.


That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Broken hose The hose on my Hoover F5837-900 Steam vac Supreme broke away from the coupler on the bottom of the unit - under/behind the recovery tank (solution tube is till attached). It might have gotten pinched in there a couple times. Problem - it was glued in the coupler really well, and I cannot get the whole thing out - hose will be too short anyway - is there a way to fix this or a part I can order instead??


You will have to replace the complete hose asm, part # 90001337 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

I have the same problem as steve967 The dyson dc16 is fully charged, runs well for 5-10 seconds and shuts down. I wait for a second or 2 and it runs again for 5-10 seconds. This will continue for numerous cycles, until I am finished cleaning. I have cleaned all the filters, and the power is good, The system will just not stay on. It is just over 2 years old. A friend of mine had the same problem with his Dyson DC16 after just a couple of months and has replaced his Dyson with a Black N De


Dear Michael_Stad,I am going to sound like a broken record but here is my same answer to another person with the same problem.I have I had the same problem with my Dyson DC16, where it only runs for a few\015\012seconds at a t ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch


... Hoover Vacuums

My Hoover Turbo has the power and motor works well but there is no suction power. I have taken all steps to ensure that there is no blockage in the pipes. I live in the Benoni area and would like someone trustworthy to repair my machine as it is only just about 1 year and 9mnths old.


Remove the screws from the funny looking thing on the back (about 10 philips head screws) and remove the blockage from the big hose. Don;t stop working on it until you are absolutely certain there is no blockage. You may need a long screw driver an ... Hoover U5396-900 Turbo Power Vacuum

My Hoover Steam vac has also stopped sucking... I have pulled it apart to clean it. Is there a way to take the bristles off to clean them as well as are there any other parts that could be the problem?


Based on your description, poor suction is related to only a few things\015\012\015\012Check filter inside lower tank\015\012Check the lower tank lid to be on properly\015\012 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?


Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Poor suction I have a hoover hush s5627 vacuum purchased about 4 years ago from Costco. It's suction power isn't so good anymore. I've checked all the lines & hoses and they're clear and I've changed the bag. I even disconnected the pipe from the vacuum unit and held my hand over the intake. While the machine roars like a jet engine the suction power just ain't like it used to be. What could possibly be the problem?


This vaccuum has a Fan Blade inside connected to the motor that spins to create the suction you feel. After a few years of use (and misuse) the blades on this (plastic) fan will be broken off, thus damaging the unit. These Fans are replaceable if yo ... Vacuums

I have a broken handle for kenmore vacum cleaner model 116.33921300(beltless). I ordered and already got a new handle. I'd like to know how I should deassemblel and put togetger old element to a new handle step by step. Could you help me?


First you have to get the headcover off. After that use a butter knife and/or flat head screwdriver and press forward on the four tabs that retain the pedal. Old Handle just prys off, a new one will press on. ... Vacuums

I have a Hoover Wind Tunnel bagless mach 4.7 vacuum that shuts off after about 30 seconds. I suspect it is overheating, but there are no clogged lines. The on/off switch is in good working order. Help!!


Is your filter clean? you should be able to see the pleats in the filter pretty clearly. also the metal screen that is next to the filter should be clean as well. if the problem continues it could be a faulty thermal protector ( a device that shuts t ... Hoover Vacuums

Model#F5858-910 hoover steam vac,silver ,spin and scrub. It doesnt seem to spray cleaner it seems to stream it now. what could be wrong? I cant get to end of where it sprays to see if something is blocking it . otherwise it works great. I have it about 8 yrs. always worked good until recently


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have an old hoover turbopower approx 1986 i think its a U1102, the prob is it doesnt pick up anymore and i wondered if it had some sort of filter on it, ive cleaned all the tubes put new bag on but its still got weak suction, could you make any suggestions, thanks


Theres a tube that come up and emty's into the bag that tube is clogged.take the bag out and get a coat hanger and put a bend in it so the end is round then work it down the tube to push out the clog ... Vacuums

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

Roomba My Scheduler started making a "grinding" noise every now and then until one day it just started grinding and then stopped (I could restart the unit, however it repeated the grinding and stopping). I have checked the wheels and all of the gears appear to be in good order. I have a hunch the brush motor may be stripped. Any opinions? Thanks: RAnderson


Hi!\015\012\015\012Further investigation (running diagnostics mode) revealed the impeller (in the dust bin) was out of whack. I got another dust bin from EBAY and replaced the impeller and motor. Unit works fine. ... iRobot Roomba 4210 Bagless Robotic Vacuum

Hoover wind tunnel cyclonic U5780900 1 year old. brush will not turn. too much slack in vbelt when in carpet position. Belt is good


Well, the V belt is normally fairly slack until the handle is dropped below 45 degrees, which is when the belt tensioner assembly drops into place. If turning the brushroll by hand when the vacuum is in this position fails to rotate the self propel p ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0654 seconds