Having problems with your Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum ?

Power not working to machine

\015 Power just shutoff as I was using it. There was a partial blockade in the bottom tubes and the filter was cleaned. Still no power to the motor\015

Answers :

All Dyson's have a thermal breaker built in them,,witch means if there is a blockage it will stop working to protect the motor it will reset itself if you leave it for 30 minutes to cool down,,.
Repair Help & Product Troubleshooting for Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a new scoba (irobot) the battery is charged the tanks were fillied and every time i hit the power button and then clean the machines "check the tank" light came on. i have done all the proper instruction checks an i have done all the trouble shooting section. the machine will only work (and that is for 5 minutes drying its head) when i hit power and the clean button twice. so obviously the machine is somewhat working


We had to prime the sensor. irobot suggested a turkey baster, but we didn't have oneso we used an empty visine bottle with the end snipped off and rinsed completely. this worked after the first try. thank you for your interest ... iRobot 5800 Scooba Vacuum

My Ultralux 2000 vacuum power head does not work on my machine but does work on a different machine. What are the possilbe problems? I tried replacing the hose with a new one and that didn't help.


It's probably due to bad wiring connections between the wands, hose and wand, or power nozzle and wand. If it came with the Sidekick, try using it on the end of the hose. If not, simply try using the power nozzle on the end of the hose (no wands). ... Electrolux Eureka Easy Clean 2 in 1 Stick and Handheld Vacuum Model 108A 1 ea

Vacuum Model 116.24614400 Unplugged working machine to move to a new area. Plugged it in and NO POWER TO MACHINE. Checked plug and it is working fine. Is there a reset button? thanks You, Barb [email protected]


... Kenmore Vacuums

Hi! I'm interested in purchasing a G3 model ; however , the seller says that the machine was working perfectly and then when switching power on a while later , the machine was " dead " . Other than the brushes , power switch or lead , is there perhaps a fuse at all which could possibly have burned out ? Thanks .


Greetings from GoVacuum.com,Unfortunately there is no fuse on a Kirby Generation model. In my 10 years of repairing Kirby's as well as other vacuums, I will tell you that 9 times out of 10, when a Kirby Generation doesn't turn on, it's t ... Kirby Vacuums

My dyson DC05 has been playing up for a while. The motorhead would start fine with green light on and after a few minutes would stop and light would go green. then the power would go on and off - seemed to only work when I had the handle a certain way. Now no power at all. is there a way that I can check if its the power in the handle section as thats the only way you can turn this machine on? Thanks in advance


As the wires that control the motorhead run all the way down the hose it is a break in the wires you will need to buy the hose assy sorry its not thesort of thing you strip down and repair  ... Dyson DC05 Bagless Canister Cyclonic Vacuum

Machine will not work, i plug it in and press the power, but nothing happens.


I have the same problem with my shark. I dismantled it and found that a thermal fuse on the bottom of the tank is blown. I am trying to locate the part now. I will post when found. ... Euro-Pro S3325 Handheld Steam Vacuum

Brushes We have A Proheat Select X2. Brand new, using for the first time, heater works, liquid dispenser works, Power brushes on machine and on extension attachment do not turn. Any thoughts? Thanks gigi2244


If the floor brushes don't turn, there is a motor for that and it maybe bad, On the attchment, vacuum is what turns those brushes, On the tank there is a knob to turn for the floor or hose, is it turned for the right application? other then that, y ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The Dyson Animal won't turn on or off. The red power button doesn't control the on/off for this machine any longer. Once plugged in, the vacuum will work and the power cord must be unplugged to turn it off. Any help would be appreciated.


The machine needs a new switch. The switch is stuck to the "on" position. ... Dyson DC05 Bagless Canister Cyclonic Vacuum

I have a Juki serger mo-634de that I am borrowing from my sister in law. She doesn't have the manual, but just got it back from the shop in good working order. I have threaded the machine, and when I manually turn the dial, it appears to stitch properly, but when I press on the pedal, nothing happens. No sound from the motor, no movement with the needles, nothing. Help! (c: Power is working, because bulb turns on.


... Vacuums

My Hoover Turbo has the power and motor works well but there is no suction power. I have taken all steps to ensure that there is no blockage in the pipes. I live in the Benoni area and would like someone trustworthy to repair my machine as it is only just about 1 year and 9mnths old.


Remove the screws from the funny looking thing on the back (about 10 philips head screws) and remove the blockage from the big hose. Don;t stop working on it until you are absolutely certain there is no blockage. You may need a long screw driver an ... Hoover U5396-900 Turbo Power Vacuum

I have a Hoover U3330 001 upright vacuum, while using it today the power suddenly cut out and it stopped working. I have replaced the fuse with a new and tested fuse, but the machine will still not power up. please can you help?


... Hoover Vacuums

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

Power not working to machine


All Dyson's have a thermal breaker built in them,,witch means if there is a blockage it will stop working to protect the motor it will reset itself if you leave it for 30 minutes to cool down,,. ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

I havwe a Breville Brita Aqua Fountain water cooler about 3 years old. Only some of the blue lights are working and the motor appears to have stopped. Power is getting to the machine and I wopuld like advice as to how I can check further before scrapping


... Vacuums

The hose keeps pulling out of machine and now power head is not working.


What kind of machine, make sure you lock it into place ... Vacuums

I'm trying to replace the power cord on my Hoover Telios vacuum cleaner. I have the machine open on the floor, but can't work out how to find the terminals on the cord rewind reel - they seem


... Hoover Telios Canister Vac Vacuum

Hi, I have been given a beautiful Husqvarna Prisma 980 and the power seems to have stopped getting to the machine.. The first time I plugged it in it worked, all the lights came up where they are supposed to, then the second time nothing =( Some help would be appreciated as I would like to fix it instead of throwing it in the bin Thanks Vicky


If you're really serious about getting this machine running, you need a service manual. Here is a .pdf download manual:\015\012 ... Vacuums

Dusty smoking smell, stops working, trips out power in house.


... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?


Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum

Hetty hoover...power switch lights up but not working at all, help?


... Henry Vacuums

The model is Miele S538, but I did not see it on the list. The suction power button( ) increasing the power does not work. The suction power button (-) decreasing the power does work.


... Miele Leo S5381 Canister HEPA Vacuum Cleaner Bagged Vacuum

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

My bissell power trak just stopped working i turned it off and a few hours later i turned it on again and it will not work. I switched over to an outlet i know works and it still didn't work I checked the outlet after and there's still power there. Is there an internal fuse?


... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

The power paw on my vacuum machine is not working.Eureka ez kleen


The filter is not the reason it's not working. Take out screws and open Power Paw, remove fur from the roller brush on the right side, there is a small gap where fur winds around tightly, cut off with scissors or pull out with a small toothpick. ... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0564 seconds