Having problems with your Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum ?

Dyson not working

\015 Was just using my vacuum and it stopped working. no funny noise to warn me something was wrong, it was like it had just been turned off.\015

Answers :

I suggest you check the hepa filter for black soot. If it is black and yucky then the motor is probably burnt out. Check out the guide at www.tasweb.org for instructions on how to fix it.
Repair Help & Product Troubleshooting for Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson seems to have lost its suction therefore is not picking up anything yet i have found that when my dyson is standing upright it has a little more suction but nothing like how it use to work. This has only happend in the last 2 weeks. I sanded a floor & though the sander picked up majority of the dust i did use the dyson to pick up the excess and it is since then that my dyson has not been working to its full potential.

Hi there,\015\012\015\012Sorry to hear you're having a problem with your DC07. You should be able to resolve the issue by following these simple steps: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?

Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My handheld dyson is not working - initially it was cutting out after only a few mins then seconds now it won't work at all despite showing green light ??

Hi there, it's Jack at Dyson.I'm sorry to hear your DC31 Animal is only working intermittently. When fully charged, this machine should have a maximum runtime of 10 minutes, or 6 minutes on the maximum power setting.There are several ... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

My Dyson DC25 animal is having issues. I believe everything is working correctly except I have realized that the mechanism which switches the hose/valve between the wand and the vacuum head isn't working properly. The two gear pieces that move the hose placement aren't close enough together, so they don't work together. It looks like there is a washer that I could potentially remove on the clear gear piece which would allow it to sit closer to the assembly. Would that work? Currently I am

... Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work

It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Currently my dyson does not work when in the upright position. When I pull the handle back, it will run, but the suction is not very good at all. I tried washing the filter, but that didn't work. Sometimes it works for awhile, but then the problem occurs after the machine has been used for awhile. What do you think the problem is?

Hi its Darran at Dyson.It sounds as though the brush bar may not be turning properly when you put the machine into the upright position. To test, lie the machine on its side in the vacuuming position (head released) then switch it on and ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have an animal dyson. The front nose dives into the carpet when moving the dyson in the forward motion, fine when pulling back. A huge amount of effort is required to move it forward. Took it to a technician and he said he could find nothing wrong. He had only short nap carpet for test. Works fine on short nap, if the carpet nap has any lenght to it like shag, the dyson severly nose dives. It's like the nose is sucked into the carpet. This problem just occured after the wife used the ho

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson works only without the prefilter

Dyson's are terrible vacuums. Sure they look cool and may work for a couple months but they start to "fall apart" no more than a year. If you have pets, then i suggest you spend the money on a machine that won't break down or give you silly issues li ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My dyson not working only working at hose part! tried everything help

Belt on the brush may be broken ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Just purchased my Dyson Ball DC24 less then a month ago. Its great when it works. The brush does not spin. At first I was able to get it working after repeatedly pushing the brush button and fooling around with the handle position. Now nothing.

If its still undr warrenty take it back i wonder if the switch is broken or a bad connection .i hope this works thanks ... Vacuums

I changed the motor in my Dyson Animal hoover and works fine but after 15 minutes it stops as if it was turned off, if i leave it for a period (2 hrs)it will start up again and work for a further 15 mins before shutting down.

Hi thereAll Dyson vacuum cleaners are fitted with a thermal cutout, which will switch off the motor if it becomes too hot. This is normally caused by a lack of airflow to the motor, i.e caused by a blockage or a dirty filter. ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

My dc 05 isnt working and i cant understand why , i have cleaned all filters etc and i also changed the fuse on the plug , which after i didi that it attempted to start but then jus cut out again so i thought the fuse had blown again , so i checked the fuse but its working fine could there still be a blockage somewhere in it or is it something electrical which means my dyson has to go to the dump :(

Most common cause of this problem is a wire broken inside the flex, usually either just where it leaves the plug (easy to fix) or at the other end (more of a problem). In either case, this is no reason to dump the machine - it can be fixed at a fract ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

My Dyson DC07 stops working after a few minutes. It works again after a further 10 minutes and then cuts out again. I have cleaned the filter and checked for blockages but is still cutting out. Can anyone help?

Have you tried calling Dyson? I had a problem with my Animal, and their tech department talked me though the fix. Worth trying them first. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson. From your description of the problem, either the brush control has been switched off (dial on the side of the cleanerhead) or the belt has snapped which may indicate a problem with the clutch. Please ca ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.

Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The motorhead on my Dyson DC05 stopped working. I bought a replacement motorhead but it also does not work. Any ideas as to what the problem may be?

It could be the hose or the pipe electrics that are not working have you got any lights on the head at all ... Vacuums

Dyson DC07 My Dyson DC07 vacuum sounds very very loud, it works fine but it's gone from a quiet vacuum to a loud vacuum cleaner, what can I do to make it quiet again?

Your better bar is miss alined put a felt tab (for chair legs thier sticky) on the side if the bar near the belt on the inside end re put in the better bar no more noise ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

No power Our dyson DC07 was working fine, then we pushed the button to turn it on. It started to run then shut off and now it is like the power is no longer there. I have checked outlets and they all work. Is there a fuse of some kind in this unit?? If so, how would I get to it?

The motor will have a thermal cut out,however chech your plug fuse and the cable as it enters into the off on switch. its known to snap here within insulation..... ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I was putting some bedding in a bag for storage and decided to ''**** it down with my dyson hose to fit it in a smaller space. My dyson quit working and now it will not turn on can you please help...??? I know I didn't **** anything up but I can't live without a vacuum!! I have tried the brush reset button but can't find another reset...

There is no other reset. The Dyson will cut out if it gets too hot, but resets itself when it cools. In doing the job you describe, I doubt that you have operated it long enough to cause overheating, or to do any other damage. I suspect the problem i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi, our Dyson cuts out after about 60 secs. We've checked all the filters plus, having read that if it works without the vortex then the problem's there (it did work) we're still none the wiser because having dismantled the vortex as much as poss, there don't appear to be any problems - any ideas?

That dyson is a old model. they don't sell it in stores anymore and the motors on dysons are made cheaply. take it into a vacuum shop. or just get a new one ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off.

This post may be of assistance: http://www.fixya.com/support/t2842769-fix_new_power_cable_dyson_dc07\015\012\015\012Hope it helps ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

Dyson My dyson stopped working, and now I cant get it to come on at all, I have cleaned everything.

Proberly fauly cable ,switch,or motor req,all parts can be supplied ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off. My DC04 cuts out after abou 5 minutes use. I think there may be a thermal cut-out somewhere?

Thermal cut out in coils of motor,you have not been keeping filers clea,I THINK.\015\012motor is avaliable ... Vacuums

My dyson dc07 works fine for about 5 to 10 min then turns itself off leave it for 10 min or so then it will work again for a bit then does it all over again. help please thanks

Your machine is overheating. This is usually caused by the dust bin being too full, your filter is long overdue for a cleaning, or there is a clog in the machine. Usually a cheap fix regardless... Wash your filter, check the removeable parts for bloc ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0657 seconds