Having problems with your Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum ?

I have a dyson dc 05 and a wire has come disconnected from the main cable inside the machine how do i get the wheel off to reconnect the cable


Answers :

In the centre of each wheel there is a different colour plug. This must be removed before the wheel can be pulled off. I used a small screwdriver to prise it out. You will probably damage the plug in removing it but they are easily available online as a replacement. You will then see two screws holding the case together. You need to undo both sides plus the screw on the top.
\015\012(If you think you may have a loose connection, then it could be the motor brushes have worn out and need replacing)
Repair Help & Product Troubleshooting for Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a dyson dc 05 and a wire has come disconnected from the main cable inside the machine how do i get the wheel off to reconnect the cable


In the centre of each wheel there is a different colour plug. This must be removed before the wheel can be pulled off. I used a small screwdriver to prise it out. You will probably damage the plug in removing it but they are easily available online a ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

HOW DO I CHANGE THE MAINS POWER CABLE ON A DYSON DC07? my wife cought the cable under the dyson and has stripped it to bare wires so i need to change the cable. i have taken a cover off near where the cable goes into the machine but now cannot get any further


How to open the cover near the cable for dyson upright vacuum ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dco5 Pulled the unit too hard to get extra flex. The plug is ok changed the fuse. I believe the cable has detached itself from the inside. How can i check the inside of the unit for cable damage


Hi.\015\012\015\012Try this site has manuals on replacing mains rewinder unit on Dc05.\015\012http://dysonmanuals.llc.nu/\015\012\015\012Chris.. ... Vacuums

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?


You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

I need to get to the internals of the machine in order to retape the electric wire that originates inside. I have removed all of the visible external screws that are keeping the 2 sides together but it still will not open. It is a Euro-Pro vacuum model ep 601. Can you help?


\015\012\015\0121. \015\0121 Lower handle of vacuum and flip\015\012over so that it lies flat on floor upside down.\015\0122. Twist 3 plast ... Euro-Pro Vacuums

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

Dyson DC05 It is a vaccum cleaner in a perfect condition but recently developed a problem. It sparks and sometimes power goes off while operating. It is clear that the wire is loose but do not know how to open the bracket of the main button on the machine. [email protected]


Hi \015\012try this site http://dysonmanuals.llc.nu/\015\012\015\012It has service manuals for the DC05. ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

How do you get into the switch area of the Dyson DC07 to replace the mains cable?


... Vacuums

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.


The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

WH5205 upright vacuum power cable replacement. How do you get at the cable connections inside? HELP! :(


... Hoover Vacuums

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance


Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

My Dyson DC 24's beater bar switch didn't actuate and the beater bar didn't turn. When I brought it to a certified serviceman he told me that a wire interferred with the switch and all he had to do was move the wire out of the way of the switch. At the time the machine was under warrantee and it didn't cost me anything. Now however, the machine is out of warrantee and the problem has returned. Does anyone know how to access the switch and move the wire out of the way?


Hi- I had the same experience but it turns out there's a small trip switch if you've taken the brush out to clean it, it needs to be reactivated by pressing the small red button to the right of the brush... took me a year to figure this out! Been mea ... Dyson Ball DC24 Bagless Upright Vacuum

Spare wire? My SEBO X4 flex had to have the fex shortened because the cable sheathing had come out of the internal gripper and there was a couple of inches of two strand wire hanging out the cable entry point before the insulation sheathing started. No problem doing this but on the live switch terminal there was a piggy back spade connector. The second wire from this went down inside the handle and just ended with a bare terminal hanging in space. It hadn't come off anything, there wasn't anyth


Greetings from GoVacuum.com,I took a picture of the Sebo X4 wiring in the handle of the machine for you. This is a brand new machine taken out of the box, this is how the wiring should look. You'll see that there are 5 total wires here. ... Sebo Automatic X1 Bagged Upright Vacuum

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

Wufe took HANDLE?WAND off the machine (dc26 dyson) and can't get back on?


... Dyson DC26 Bagless Canister Cyclonic Vacuum

How to get at wire in fly wheel


This video will show you ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Hello, I,ve just bought an Italian designed 3 bulb 70's wall lamp. It has a 2 wire lead feeding out with 2 wire lead running from one bulb socket To the other 2 inside the casing. I'm trying to wire it in my porch which has 3 wire cable coming from a 13amp plug for power. Any suggestions on making this work please ?


... Vacuums

Dyson DC7 wire gets hot


Hi.\015\012\015\012Definately yes & ASAP. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Upright self propelled Windtunnel model: The self propulsion does not work and I can see why. I need to know how to get the top cover off the machine to get to the broken part that engages and disengages the wheels. Can you tell me how to get the cover off?


Turn the machine upside down and locate about half a dozen recessed screws which hold the bottom and the top of the machine together. ... Hoover Vacuums

I have a dyson alergy machine, I have emptied it, but I would like to clean the filter. I can't locate where the filter is or how to get to it to clean it. The manuel for this is not with the machine. This machine came with the house we live in. Could you help me please? Laurie


Greetings Irlawren3, \015\012\015\012It all depends on the model you currently have. The filters on some are above the motor and some are on the side housing. Its pretty clear looking at the unit where the filters are located. I would su ... Vacuums

Both of the wheels are wobbly and loose on my Kenmore upright vacuum model 721.37060. I don't see where I can remove them to analyze and fix the problem, which seems to be that the wheels are loose on their axels. How do I get the wheels off and what do you think I'll find inside?


Most if not all vacuums have an access panel on the bottom.It may be held on by a couple of big plastic clips,the kind you squeeze together and it releases a door.Some have plastic screws.There may also be a couple of phillips screws along with it or ... Kenmore Vacuums

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1167 seconds