Having problems with your Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum ?

I have my Dyson DC05 for few years. The 'Red light' on its turbobrush is on and cannot get it running. Can anyone help? Thanks, Angus


Answers :

Hi there Angus, SmartAlec from NelsonVacuums.com.au here. That light normally means the motor is stuffed but it will also light if the roller cant spin. So just check there is no obstuction stopping the roller from turning and also remove the roller and take of the end caps and clean out the debris that ias likely there too. If this isnt the problem unfortunatley you will have to get a new head. Hope this helps. Happy Vacuuming :)
Repair Help & Product Troubleshooting for Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have my Dyson DC05 for few years. The 'Red light' on its turbobrush is on and cannot get it running. Can anyone help? Thanks, Angus


Hi there Angus, SmartAlec from NelsonVacuums.com.au here. That light normally means the motor is stuffed but it will also light if the roller cant spin. So just check there is no obstuction stopping the roller from turning and also remove the roller ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I am trying to get replacement parts for the shark ultra steamer, cannot find anywhere. Can anyone please help. Thank you


You can start with this URL\015\012\015\012http://www.vacsewcenter.com/browser.asp?AdvSearch=Shark&gclid=CKrXi5bEyaQCFQf3iAodyVcpEw\015\012\015\012Paul ... Euro-Pro Shark SC-505 Handheld Steam Vacuum

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.


Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I cannot get the feed dog on my Singer 4423 machine to raise. It is the first time I have dropped the feed dog to try sewing on a button & now it will not come back up......can anyone help please & thanks!!


... Vacuums

HA-871? I'm not sure if anyone can help with this, but I've got a **** Smith brand HA-871 alarm system which I haven't used in years. When trying to get it working, not only have I forgotten the code but I can't remember how to enter it (as in, 4 digits and a #, or just the 4 digits, or something else...?). As I am able to get into the alarm box with the key, does anyone know how to reset it and enter the code? I can't find the manual either. Thanks to anyone able to help with this!


Incase you are still interested you set the code with the four jumpers inside the unit.\015\0121st digit is the brown wire\015\0122nd digit is red wire\015\0123rd digit is orange\015\0124th digit is yellow ... Vacuums

Does anyone know where I can get a motor bearing for the 3595 upright vacuum. Called Bissell and they say I have to be an authorized dealer to get "internal" parts and called their "authorozed dealer" and they told me they cannot get the part and I needed a new motor...ridiculous! Anyone put a bearing on these and if so where did you get it from?


Bought the whole motor assembly for mine, no bearing only part available. THis vacuum now headed for its third motor. " $45 dollars is still cheaper than a new vacuum". That's what I said the first time... ... Bissell CleanView 3596 Bagless Upright Vacuum

I am trying to register my shaver on www.philips.com/welcome and get 1 year additional guarantee. I also expect to get Updates on all the latest shaving and grooming Hot exclusive offers And Personalised support. I cannot get any of these and cannot register my shaver. Please help....


... Vacuums

Hello, could you help please. I have a Bissel ProHeat 9400-M. The water remains in the bladder when the machine is on, in other words nothing happens and I cannot clean with it. Inside the tank the small flap is in the open position. I have always used your products although I did run the Bissell over an area that had been cleaned with another product. Could that have caused the problem by blocking it somewhere? I have cleaned everything and cannot see a blockage. Thank you for your help.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

After removing the filter, I cannot get to battery on the Dirt Devil Kone M0213, there are two horizontal screws. Removing them does not help getting to the battery, no way to remove the insert where the battery is located.We have two of these, however they did not come with a manual for dis-assembly. Please help or proved a diagram on how to remove the battery. Many thanks, Wesley Lennon


Sheesh, did anyone actually read the person's question? It's about the battery, not the filter.\015\012\015\012You have to get the outer cover off and it's not easy. There are four tabs which need to be released. I have to use a very sha ... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum

I just purchased a Sebo Airbelt D canister vacuum. I plugged it in and used it for ten seconds then turned it off, retracted the power cord and now cannot get the power cord out of the machine. Did I not spend enough money to get a quality product? Does anyone have any idea how to get the power cord out without breaking the machine?


... Vacuums

We have a Eureka built in vacuum system model cv800B. The unit is about 15 years old. It runs for about 5 minutes then shuts down. If you wait atleast 10 minutes you get another 5 of run time. Any help would be appreciated. Steven


... Vacuums

Bissell powerforce My lower pickup tube became clogged so I removed it and cleaned it out and reinstalled it.Now everything runs good but the vaccum want pick up any dirt .I replaced the bag andf when I turn it on it just exhaust air but does not have any suction,I tired tp pull the bag door of while it was running whick I could not do so it has plenty of suction inside just not getting any outside can you help?


... Bissell Vacuums

I have an Electrolux Silverado deluxe canister vacuum that won't run. It was running fine, I turned it off to move the plug and then it won't turn back on. It is getting power to the switch. Any help?


... Electrolux Vacuums

I have Model 9400-3 Bissell Pro heat select 2X microban. I cannot get the solution to come out to shampoo the carbet. I cannot find my instructions that came with the shapooer. Please help.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Elna 7200. The bobbin spring seems to have come loose, but cannot figure out how to get it in place again, so we cannot work, Pls help.


The best course of action in your case is to take sewing machine center and let them show you how to get it in place. They may even help for free because you might become a potential costumer. I hope that there is a repair center near you. ... Vacuums

I have a carpet magic steam machine. The pump worked fine yesterday. Today, I cannot get the pump to prime. (The solution resevoir is full.) Is there anything I can do to help prime the pump? Thanks for any help!


... Vacuums

Eureka 2961AVZ Will not start ...I get a momentary flicker of power about every 3d or 4th time that I flick on the power sw. Outlet is fine / Plug looks good / chord looks good / I see no obstructions ........Would appreciate any helpful thoughts ....Trying to get Mom's Eureka 2961avz back up and running. Thanks


CAREFUL! This is how my problems started. The cheap switches (and wiring) Eureka is using in some models, especially my model) should provoke a lawsuit imo.Here's my story, just in case it might help. Mine started with a problem very similar ... Eureka 2961AVZ Bagless Upright Vacuum

Dead motor I purchased a new motor for my Dyson Animal but I cannot figure out how to get the thing apart to replace it. There are weird star shaped screws but I can't even see how removing those would get me where i need to be. HELP!!!


Ace Hardware or Home Depot should have your star screws ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Repair I live in Lumberton, N.C. and purchased an Electrolux Oxygen at the local Lowe's which I have been unable to find anyone to repair because theyinsist they cannot get the parts. When I called Lowe's where I boughtit they said they cannot return it for repair. What do I do ? I think it needs only a [email protected]


In your owner manual there should be a number you can call for service. If less then a year old, then it is under warranty. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Dyson DC17 Animal User's Guide says put plunger in out position. I cannot get the plunger to move and I'm not really sure if I'm trying to move the correct part. Cannot locate my user's manual for help.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have to replace the power cord on my Bissell upright pet hair eraser vacuum because it is damaged from getting run over by the vacuum. Familiar story? Rather than pay a technician a lot of money, I feel I should be able to tackle this myself (went to college and everything). What are some pointers to help me bravely tackle this without the help of a male (no offense guys)?


Of course, its simple.\015\012Use electric tape to make sure the wires never touch, usually a phillips screwdriver will do to uncscrew the machine.\015\012just make sure you line up the cords the right way, positive to +ve and negative to ... Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

My Miele Solution HEPA 5000 vacuum cleanr gives off a burning smell but will continue to run with a varying motor tone. I have not run it for more than a minute like this. I have reviewed responses to similar problems but cannot figure out how to access the motor. Can anyone advise?


... Miele S318 Bagged Canister Vacuum

The neck on my EL7024 cracked. I bought a new neck and now realize that I must take the floor cleaner apart to get the neck switched- how do I do that? I cannot find my manual or any help on the electrolux website...help, I'm in dire need of vacuuming my house!


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1312 seconds