Having problems with your Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum ?

Hi, our Dyson cuts out after about 60 secs. We've checked all the filters plus, having read that if it works without the vortex then the problem's there (it did work) we're still none the wiser because having dismantled the vortex as much as poss, there don't appear to be any problems - any ideas?


Answers :

That dyson is a old model. they don't sell it in stores anymore and the motors on dysons are made cheaply. take it into a vacuum shop. or just get a new one
Repair Help & Product Troubleshooting for Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, our Dyson cuts out after about 60 secs. We've checked all the filters plus, having read that if it works without the vortex then the problem's there (it did work) we're still none the wiser because having dismantled the vortex as much as poss, there don't appear to be any problems - any ideas?


That dyson is a old model. they don't sell it in stores anymore and the motors on dysons are made cheaply. take it into a vacuum shop. or just get a new one ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have owned my kirby sentria for 2.5 years and have had no problems until now. The vacuum still works but I cannot lower it all the way down or the light will turn off and it will start to smell like something is burning inside. I use it on the 2nd or 3rd setting with no problem. I have changed the belt and cleaned all the hair and strings that were on the roller but it still has this problem.


Kirby has a 3 yr back to base guarentee so contact ur local rep or kirby direct and thy will sort it all from there, hope this helps :) ... Kirby Vacuums

No suction I have a similar problem - volta vortex bagless vacuum will not ****. Worked for 1 job then quit sucking, I have had the heads replaced, then the barrel - 2 months later same problem. I push the power lever to max - 10 seconds later it turns itself down and doesn't work properly. I am over it, now looking for refund


Hi there SmartAlec from NelsonVacuums.com.au here. The problem is going to be the filter. THis kind of vacuum basically replaces the bag with a simple filter and the vacuum ... Vacuums

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?


You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?


... Kenmore 34722 Grab-N-Go Upright Vacuum

The spin brush in the head is not working. I have tried the button which supposedly activates it, but it is still not working. How can I fix this problem?


You will need to replace the yoder loop with in the head. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a light ballast that stopped working. The lights around this one bulb still work but changing the light bulb did not fix the problem. Any idea what is going on here?


The ballast is like a fuse and the ballast is blown .\015\012you will need to replace the ballast as it will let current thru for some bulbs but not enough to light them all up.\015\012also if you use old bulbs that are alomst blown and n ... Vacuums

I have a Craftsman wet dry vac with blower capability (22 L). While I was using it to **** up water, the water came out of the blower hose. Now I can't get it to work as a vacuum. What can I do to fix this problem? Is there a toggle switch somewhere that allows me to choose vacuum or blower? Also, will the vacuum still work without the filter nut attached to the plate? Please let me know at your earliest convenience. Thank you.


... Craftsman Vacuums

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

I HAVE A FANTOM VACUUM CLEANER MOD.#F1205400. I PURCHASED IT ABOUT 6 OR SO YEARS AGO.IT WORKS PERFECT,AS FAR AS SUCTION, THE ONLY PROBLEM IS ABOUT 2 MONTHS AGO,SOMETHING HAPPENED TO IT AND IT GOT VERY LOUD, KIND OF LIKE A CAR WITHOUT MUFFLER. I TOOK IT APART,AND FOUND NOTHING OBVIOUS. CAN YOU GIVE ME SOME IDEA OF WHAT I CAN CHECK TO RESOLVE THIS PROBLEM. AS I SAID BEFORE IT STILL VACUUMS GREAT. THANK YOU, VINCE


You probably have a bad motor bearing. I don't know if the motor is available now or, these older Fantom's are obsolete along with most of their parts. ... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

HOOVER Cleaner F5857-011 BRUSH'N'WASH Problem: Brushes not turning under load. Will turn slowly when raised from floor/carpet but can be held still by light hand pressure. Checked listed possible causes as per handbook but still not working.


... Hoover Vacuums

Same problem but the suction still not working


Try taking off the U bend and see if there is suction coming out from where the right end of the U bend connects. If there is suction then the problem lies after the u bend in the hose or wand. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My dyson animal works for a while then shuts off...i guess it's getting hot and automatically turning off to keep damage from occuring. i have cleaned the filter and all the collection basket, but am still ahving problems. it was just services a year ago and a new switch installed. please help!!!


The belt that drives the beater bar may be broken or stretched, causing the motor to turn more freely, therefore causing the motor to rev beyond it's design.Jim ... Vacuums

All the suction has been lost at the bottom end, the hose still works and sucks fine. what can be the problem? there doesnt appear to be any blockages either


It sounds like you must have a blockage behind the beater brush on the bottom of the v ac ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vaccum brush not working. Filters clear of debris has been smoking will not **** anything up help! I cleaned the brush up, cut hair out, etc. Still the brush will not turn and it smokes a little, is this a belt problem?


Yes you need to change the belt. Here is a link to the belt you need and to a manual you can view:Bissell Lift-Off Revoluti ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My vacuum died. It won't turn on. It is not the outlet. Is it a blown fuse? How do I replace the fuse? Where does it go? This vacuum is a little over 2 years old. My older Hoover WindTunnel STILL works and has never had this problem.


It's probably the power switch. My switch was dicey for a couple years, finally gave out. Easy to replace.\015\012\015\012Remove the two screws just above the WARNING on the rear of the upper handle assembly, then slide the whole assemb ... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1


Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

I have a Hoover self propelled WindTunnel vacuum( Model U6425-920) that stops in the middle of cleaning. I have changed the flat belt and I'm still experiencing the problem. I usually have to wait an hour or so b/4 it would work again. Any advise?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=632298\015\012Generic problem for all Vacuums\015\012I have a Hoover self\015\012Posted by thjunk2007 o ... Vacuums

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0563 seconds