Having problems with your Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum ?

Hi, I have a DC05 Dyson Absolute Turbo Brush (I love it!) and have had it since 2002. Today it stopped working!!! Just would not turn on. New filter in, checked the fuse in the plug. Can anyone throw in any suggestions, would love to self-repair if I can. Right now am expecting a technician out on Tuesday at £69!!

Answers :

Repair Help & Product Troubleshooting for Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, I have a DC05 Dyson Absolute Turbo Brush (I love it!) and have had it since 2002. Today it stopped working!!! Just would not turn on. New filter in, checked the fuse in the plug. Can anyone throw in any suggestions, would love to self-repair if I can. Right now am expecting a technician out on Tuesday at £69!!

... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Hi., If anyone could help it would be greatly appreciated, I have a Flair 3055 ventalation system in my house and over the last five years two fan motors have gone bad. it has been mickey moused together by a local repair man, and as of last week, it has died again. At 4-5 hundred a pop I would like to fix it myself, can anyone suggest a good replacement motor that will fit and work. My honey has breading problems and at this time of year, every penny is allocated, so time is of the essence. t

Hello George, Sorry about your predicament. Various fans are available for your unit but since you say the unit has been mickey moused together adjustments must have been made to the fan seating and system therefore if you order any particular fan th ... Vacuums

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.

... Bissell Vacuums

The roller brush on my Hoover Z700 vacuum no longer runs when you tilt the handle back. I have tested every part that I can: the motor is good; the "magnetic switch" at the pivot point is good; etc. I'm now stumped. Any help or suggestions would be greatly appreciated as I don't want to throw away a $400 vacuum.

Has this not got a rubber belt drive? ... Vacuums

I have an Electrolux Oxygen 3 vacuum I purchased rebuilt. After 1 month the power stopped working. I took it into Electrolux Authorized repair dealer, which was a horrible experience. When we received it back it was clearly not as powerful as before. Does anyone have any suggestions on what the problem may be? I would rather fix it myself than take it back to them. The next repair center is too far away. I am pretty good with fixing things, just needs some guidance. I think the repair center rep

Never have liked Electrolux doing any repair because it has been my experience that they don't do what they say they did....if you can read between the lines.....give me a picture of the unit and more details and I'll try and help you. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

No suction I just replaced the bag, and normally after this I have a lot of suction. Now that I have changed the bag I have less suction that I had before. Not even enough to picj up dog hair. I snaked he hose and checked all of the connections. It seems to have an air leak but no amount of tape will fix this. I cleaned the filer as well with warm water and dried it and re installed but still absolutely no suction. I am ready to throw it out! Any suggestions would be appreciated

1, Does the blower (discharge) side blow bunches of air??Yes: Something is clogged from the bag to the hose end. Try blowing out the hose from the discharge side.Or: The bag is not properly seated. Make sure that the plastic piece is ... Kenmore 23313 Whispertone Bagged Canister Vacuum

A 'burn' hole has appeared in the Microwave Outlet Cover causing arcing (or similar sparking and blue flashing!). Would replacing this cover with a new one solve the problem or does it suggest something that would quickly reoccur? Would it be an economical repair or should we ditch the machine for a replacement? Thanks in advance etc it is appreciated.

... Vacuums

The Bissell Proheat 2X doesn't release the solution. I have cleaned everything I can see and understand there is a filter somewhere. Would like to know if that would even help... ANY OTHER SUGGESTIONS WOULD BE APPRECIATED! No men around just us girls and we have NO idea how to fix it!! Thanks-Cheri

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel

The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Hi I have a panasonic SD251 bread maker. The circlip for the bread pan has broken and I have not been able to purchase a circlip small enough to fix it. Any suggestions on how to get a replacement circlip would be greatly appreciated. Even the size of the circlip required would be helpful

... Vacuums

Hi, I have been given a beautiful Husqvarna Prisma 980 and the power seems to have stopped getting to the machine.. The first time I plugged it in it worked, all the lights came up where they are supposed to, then the second time nothing =( Some help would be appreciated as I would like to fix it instead of throwing it in the bin Thanks Vicky

If you're really serious about getting this machine running, you need a service manual. Here is a .pdf download manual:\015\012 ... Vacuums

We have a hoover porta vac. that at first it would sometimes come on and sometimes not. It did completely stop coming on, so I have changed the switch and the cord but with no luck. Could you offer any suggestions or is this a motor situation. To my knowledge the motor was not making any noise. Your help would be greatly appreciated. Thank You, Molly Maid of NW Fla.

If this has had heavy use, the carbons in the motor may be worn. ... Hoover CH30000 Bagged Canister Vacuum

I bought a Hampton Bay Hawkins 44 " ceiling fan (117 391) and would like a remote that I can control the speeds with not just the on and off. I have a pull chain for the speeds but would like to use a remote instead. Is this possible? I have a Hampton Bay Redington IV and love the remote. I'm looking for something like that. Thanks Madeline Lepisto

... Vacuums

I have an Eureka Express canister vacuum - I believe it's model 8284 - that just stopped working. Plug it in, turn it on, and absolutely nothing happens. I took it to the local sew and vac place and they say it's a circuit board that is no longer available. I've looked at all the parts lists and diagrams for that vacuum and I would swear there isn't a circuit board there. (I wouldn't have even thought that in 1989 they would have used circuits.) In any case, I absolutely love this machine a

Given the age of the machine weighed against you fondness for it, unless you can find a fault with either the switch or the cord, there is little else that can be done. With time the electrical lead can break down and one o ... Electrolux Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest

I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac

... Vacuums

Self-propelled Hoover windtunnel (with bags) will not self-propel. Belts are all in order, but I am quite sure it has to do with the cable. How would I fix this and how does the end of the cable with a nut, connect?

This might help - go to following website and look for "troubleshooting" \015\012http://www.fixya.com/support/p40544-hoo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover U6637-960 the self propel is not not working. When lowering the handle it acts like it would like to work but the roller will not turn. appears to be something to do with the self propel part of the handle . took the screws aout but can not get it apart. Is there another belt of something in there?

This vac has 2 belts. If both self propel and roller not spinning then most likely it is the wide flat belt broken or off. 4 screws on the bottom should gain you access to the belt area. another issue for this model series is a worn pulley on the rol ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

After using the vacuum for a while it would stop running. After sitting several hours it would run again. Now it won't run at all. It was just a couple of months old and I haven't been able to use it again. It was never used much and we paid good money for what has turned out to be a poor machine. Any suggestion?

... Dirt Devil M130000 ''i'' Dual Cyclonic Upright Vacuum Cleaner Vacuum

Oil recently acquired a filter queen with no instructions would like to know where the oil goes? if anyone can help. thanks

Guess I don't understand what you are asking, The Filter Queen vacuum doesn't use oil. ... Filter Queen Majestic Canister Vacuum

Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900

Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Burning smell how do I get the bottom section apart to clean it out- burning smell when i have the spin brushes turned on. Any help would be appreciated cause I love this machine and hubby told me it couldn't be taken apart to be fixed. Thank you.

The bottom doesn't come apart. you have to remove the top cover to get to any components. But if you have a burning smell, then it is probably ther motor and would have to be replaced. Motors cost anywhere from $70 to $90. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.

You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

Would like a copy of the Bissell Big Green Clean machine 1670 -E instruction leaflet, I recall it was only a few sides long, unfortunately a friend i loaned it to lost it and I just wondered if anyone could help? Thanks

... Bissell Vacuums

The belts are burning , I just replaced the belt as the last one seemed to be streched out. The little green light indicating the self propellsion in only on sometimes. Can anyone help me?

If the roller/beater is jammed with hair and stuff and not spinning freely that will cause the belt the burn. ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0422 seconds