Having problems with your Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum ?

Dyson dc04 how does the switch assembly come out of the casing?


Answers :

There is a tiny hole at the side of the switch push something in this to push the clip that holds the switch if you can do this there is a screw that you undo to remove the switch you will need a t15 screw driver
Repair Help & Product Troubleshooting for Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson dc04 how does the switch assembly come out of the casing?


There is a tiny hole at the side of the switch push something in this to push the clip that holds the switch if you can do this there is a screw that you undo to remove the switch you will need a t15 screw driver ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Dyson DC04 vac.cleaner how do I access the on/off switch casing to repair a broken wire


... Vacuums

I need a Dyson DC 17 Total Clean exploded parts diagream that shows the switch assembly. There are two small springs and a small plastic part that were loose inside the switch assembly. This caused the vacuum to shut off in the full upright position which is the position you use when using the wand.


I don't have a full diagram for you, but I do have a photo of how they are meant to be assembled: ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off. My DC04 cuts out after abou 5 minutes use. I think there may be a thermal cut-out somewhere?


Thermal cut out in coils of motor,you have not been keeping filers clea,I THINK.\015\012motor is avaliable ... Vacuums

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

DYSON DC04 how to remove switch housing to check


Its most likely not the switch, check the power cord.. check where the cord meets to the vacuum. the cord could be going bad and most likely not a loose wire. ... Vacuums

Suction only coming through the wand when its replaced its not switching back to the upright. I have a dyson DC28 animal


Hi there, it's Jack at Dyson.I'm sorry to hear your DC28 doesn't seem to be working correctly. It sounds as though the change-over valve may be jammed - this diverts the suction to the hose when you remove the wand, and back to the cleaner he ... Dyson DC28 Animal Bagless Upright Vacuum

Dyson DC23 Vacuum shut off and came on. Thought it was a problem at the electrical outlet as when moving plug it would come on again. Seen canister was full, emptied it and cyclone was quite plugged up so poked out the dirt. Had dog hairs in it as well as some ashes I had just vacuumed. Plugged unit in again and pressed switch. Will not come on. Tried another outlet. Is there a reset button somewhere or could the ashes have seized the motor. What can I try besides taking it to a repair sho


... Dyson DC23 Bagless Canister Cyclonic Vacuum

Today i was hoovering, and then my dyson just cut out! i left it a few hours then went back to it, it gave a little noise when i switched it on, then again i tried but it failed to come on! ive even changed the fuse in the plug! and now my dyson wont turn on at all, ive cleaned everything there is too clean! help! :D


It looks like you need a professional repair. If you're really lucky this may just be a break in the flex, or the switch has failed - both relatively cheap and simple to sort out. More likely, though, is a problem with the motor (carbon brushes worn ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off.


This post may be of assistance: http://www.fixya.com/support/t2842769-fix_new_power_cable_dyson_dc07\015\012\015\012Hope it helps ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

I have a dyson dc04 vaccuum cleaner and i want to replace the cable to the switch how do you get to the switch


Hi there SmartAlec from NelsonVacuums.com.au here. This is a bit of a tricky one on your first go so be gentle. Basically what you have to do is lift off the switch cover t ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

How do you reassemble a DC25 (dyson) switch assembly? I needed to replace the switch, but do not know where the


The best thing to do with Dyson is let Dyson service the vac. They are not meant for the consumer to repair. They are manufactured differently. ... Dyson DC25 Vacuum

My Dyson DC15 has suddenly become very reluctant to turn left. This is only the case when it is switched on and irrespective of whether the roller brush is running or not. When the cleaner is switched off it behaves as normal as far as steering is concerned.There is no obvious problem with the ball or steering swivel mechanism. Any ideas ?


Hi its Darran at Dyson. Although strange, I believe we have a solution. It sounds as though the cleaner head hose is blocked. When the machine is running the suction will be pulling against the bloskage causingt he hose to contract and p ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Switch button assembly dyson - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Hi there,If you're having difficulty with your DC17's switch, I'd encourage you to give our Helpline a call on 1-866-693-9766, as we'd appreciate the opportunity to provide further assistance.We'll look forward to hearing from you. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Pictures of dyson dc17 power switch assembly - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson dc04 wont pick up,motor working,replaced clutch assembly but still dosnt turn brushes


You need to go through a process of elimination. You are better doing that here: Dyson advice forums ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Have got motor out of dyson o7 and cannot see where they go back on the switch only has 2 connections and 4 wires coming in


The two brown wires connect to the switch, and the two blue wires connect together.\015\012\015\012www.dysonmedic.com has some good info. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Heritage 2 - black wire pulled out from motor assembly, comes from power switch. Where does it go? Need wiring pictorial and schematic/wiring diagram. Can anyone please help? Many thanks, Malcolm


... Kirby Heritage II Vacuum

I have a Dyson DC04 which is making a strong burning smell within a few seconds of switching on. Is this likely to be the motor and if so can it be replaced?


More likely it is the beater brush which is jammed and not turning. Turn the machine over and remove the bottom plate. Unhook the drive belt, then try to turn the beater brush--it is likely bound up with string, thread, and hair. Try turning the mach ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

I have had a dyson vaccuum cleaner for three months and it does a great job, but the red on/off power switch won't stay on now. As soon as you press it down to turn on, it comes right back up and turns off. What can be done?


Hi its Darran at Dyson.Call our Helpline on 1866MYDYSON and one of our advisors will be able to arrange for this to be reparied. As your machine in only 3 months old, this should be covered by the warranty. Kind regardsD ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The hollow tube underneath my dyson dc04 keeps coming out of position and it wont pick up. Should it be fastened into place with something.


It is suppose to swivel some. That is why it is not fastened in with a screw. It sounds like to plastic molding that was suppose to hold it in place has worn down. You will need to replaced that part. ... Dyson Vacuums

Electrical problems with Dyson (DC04?). Machine sometimes does not start. Something to do with the on/off switch and flex?


... Vacuums

How do I remove plastic cover plate over the switch assembly within a dc04?


Have a look at www.dysonmedic.com which has some great info on your machine. ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

My dyson will not switch on , the last time I used it the power faded in and out a couple of times I wiggled the lead and it continued to work. However today it will not power up, I have changed the fuse just in case


Hi from uk the symptoms you described is a classic fault with where power wire has broken within the main cable usually at pint where it enters the vac ? hence wriggling wire temporarily makes contact are you sure the wires in plug are ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do I remove a motor from a Dyson DC04? The bottom plastic cover can be removed by unsrewing the tork screws but the cover beneath the filter won't come off


I can't say exactly how to do this, but when you can't find the screws to take something apart, they are usually hidden by something else. You did good looking under the bottom cover, but what you're looking for is elsewhere. If there is a seam or ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0528 seconds