Having problems with your Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum ?

Will be using my dc07 for about 10 mins then it cuts out i leave it to cool then it goes for about 5 mins and carries on like this

Answers :

There is a thermal cutout on the motor causing this problem because it is overheating. Either it needs the filter replacing and a good blowout with compressed air or the thermal switch is faulty. Try replacing the filters first and if the problem persists it is probably a faulty thermal cutout. Dyson can either replace under warranty or an engineer will call and do a home refurb for a fixed price of £60
Repair Help & Product Troubleshooting for Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Will be using my dc07 for about 10 mins then it cuts out i leave it to cool then it goes for about 5 mins and carries on like this

There is a thermal cutout on the motor causing this problem because it is overheating. Either it needs the filter replacing and a good blowout with compressed air or the thermal switch is faulty. Try replacing the filters first and if the problem p ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

HI i have a electrolux vitesse pet lover 1600w modl ece09113.When used it runs for 10 to 15 min then turns of has been like this from new.I know it says it could be blocked but have cheaked and seems to be fine. As this hase done this from new could it be a thermo cut out switch faulty. Thankyou. Dave.

... Electrolux Vacuums

Roomba Schedular I have a Roomba Scheduler and it has worked great until recently. Suddenly it quit working. When it is charging the power light goes from red to green as it should, showing it is ready to use. When we turn it on to use, it will only go on for a few seconds then it shuts off like it is out of power. It is like it isn't really charged. Is there something I can try to make it work?

Let it charge for a full 24, or even 48 hours, regardless of the green light. If it still dies you probably need a new battery.. or worse. ... Roomba Robotic Floor Bagless Vacuum

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!

... Vacuums

Dyson DC07 My DC07 cuts out after 5 mins and I want to replace the thermal cutout. I have cleaned it thoroughly, including the cyclones but it still cuts out. How does the plastic moulding around the motor dismantle? I have started by removing the 4 torx screws but the upper grey housing does not want to detach and I am worried about breaking the plastic. Appreciate any advice.

Try this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Regards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a bissell powerwash 1690 and there is no whine noise when I switch on the spray button like it used to, as I used to treat the carpet with the cleaner first for few mins before using the suction, but now no longer a sound when I switch on the spray - what could be the problem?

... Bissell Vacuums

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off. My DC04 cuts out after abou 5 minutes use. I think there may be a thermal cut-out somewhere?

Thermal cut out in coils of motor,you have not been keeping filers clea,I THINK.\015\012motor is avaliable ... Vacuums

I have a shark iron model G1495N It has a cut in the wire inside the rubber hosing that goes around the cord from the base of the iron When using it yesterday I didn't see the cut and it sparked after plugging it in and heating up Is not usable at all What can I do to repair it if at all? I've had it since sept 2008 Thnxs

It's probably best to replace the device, when dealing with sparks and exposed wires. \015\012\015\012If you're electrically-inclined, feel free to pry it apart (when unplugged!) and see if you can re-attach things, but generally soldering or g ... Vacuums

Help Hi I have had my irobot roomba model 4000 now for 3 months now, I just LOVE it sooo much. I have used it everyday since I got it. But now it is not working. I cleaned it all out I even sprayed it with that air spray can. What happens is, It starts to go then it acts like there is something in the way and stops then goes the other way, then goes off. What is wrong? Please help!!!

I had the same kind of problem with my model 400 today...after starting it and having it go in a circle for 30 seconds or so it would finally run into something and then back up a few inches, turn, then go forward a few inches, then back up a few inc ... iRobot Roomba 4210 Bagless Robotic Vacuum

My vacuum shuts off after about 10 min. of use and won't turn back on again for a few hours. It feels hot and smells like it is overheating, what is this most likely from?

... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

My vacum keeps sutting itsself off after a few mins of use. I need to vacum the whole house and dont have tinme for it to cool down every 10 mins

Something is plugged. What you describe sounds like the motors' thermal limiter is opening the circuit to prevent the motor from overheating. You need to open and verify that evey air passageway is clear and the unit has good air flow. I bet you find ... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara

... Vacuums

DC07 cutting out

This may help!http://www.fixya.com/support/t192124-overheating_dyson_dc07 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

HI, I have a Kenmore 25813 and it seems like there is an intermittent short. When I have the extension wand on and the power floor attachment on, when it rotate the wand the light cuts out and so does the power floor attachment, when I twist it back it comes on again. I don't have this problem if I remove the wand and just use the crevice tool with the hose. Any idea where the short might be and can I fix it myself? Thanks. Gary

This is common you may have a short in the contacts from the handle to the wand or a break in the cord that goes into the powerhead ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

Steam cleaner im using my cleaner have it all working but it just seems like its not cleaning right!!! i went over it for about 20 min and it has only cleaned a little of the stain am i doing something wrong or does it just take a very long time to clean!!

If it is spraying ok and the brushes are turning, then maybe the cleaner isn't strong enough for the typa of stain you are trying to clean. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Electrolux power nozzle, model 1692, power cuts on and off. I don't have the manual for it, but I'm trying to remove and clean the brush compartment. I removed the top, but not sure how to get to the brush. I would like to find a manual for it, because it's completely different than the one I use to have.

... Electrolux Vacuums

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis

Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can't for the life of me find the wand release button on my actual Dyson.....the manual pictures don't look like the parts on my Dyson....I don't have a hose with a wand release button....the hose just goes straight up inside the handle....Can someone help me? Thanks :)

Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. S ... Dyson DC07 Bagless Upright Cyclonic Vacuum


Hi there SmartAlec here. The noise is coming from the clutch, you have either got something caught in the roller or maybe the bearings are siezed in the brush roller. I have made a video to show you how to fix either problem. If the video is helpful ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I bought a house that has a 1970s GE microwave oven that's built-in above a traditional oven. (Unfortunately, I can't locate a model number for the microwave.) I'd appreciate having information about the "food temp control," which is on the front of the oven. There is a wire probe that goes from the inside of the microwave to the food. I assume that relates to the "food temp control." I'd appreciate having any information about how to use the "food temp control." Also, I 'd like to know wh

I serious doubt that probe would work any longer for they go out in ten tears or less ... Vacuums

Burning smell i have a dyson 14 animal and it quits working after about 3 min of use and it smells like its smoking

Have you checked the the hoses are free of debris?\015\012Is the setting for floor on when you are vacuuming the carpet.\015\012\015\012Turn id on an see if it will **** up some pennies.\015\012Use the hose for that. \01 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it

The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

DC07 stops after short time using and will not start until it has rested for a while. Is it running out of steam like it's owner?

You could try washing the blue filter. This happened to mine and when I washed the filter according to instructions I found on the Dyson website it was fine! ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I bought a used vacuum seal machine (hobart model ht-120) it does excellent vacuum but it doesnt seal correctly all the time. it seems like there is something wrong with the valve that activates the bar that goes up and makes pressure and heats the bag for complete sealing. The heating is perfect but what is not working is what make the bar go up and down.

... Vacuums

Power cuts maybe after 10 mins use, then after switching off for an hour or so, it works again! repeat.

I would think that it is probably a motor going bad and tripping the overload switch. After the overload resets, it will run again. Is there a chance that the motor is still under warranty? Some vacuum maker warranty the motor for longer than the r ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 2.5394 seconds