Having problems with your Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum ?

Dyson vacuum brush roll doesn't turn

\015 The vacuum has 2 settings: bare floors and carpets. When turning the knob to bare floors, it works great. When turning the knob to the carpet setting, the brush roller doesn't engage. Any ideas?\015

Answers :

The brushbar should only turn when you meet two conditions:
\015\0121) When you step on the front of the machine and pull back on the handle (recline the machine in other words)
\015\0122) The dial is set to CARPETS
\015\012
\015\012The brushbar shouldn't turn at all when it is set to the BEAR FLOORS setting.
\015\012
\015\012To rectify the problem - call the Dyson Helpline so that they can refer you to an authorized dealer in your area - the repair dealer will inspect the dial and figure out why the functionality seems to be switched. They'll be able to fix it for you.
Repair Help & Product Troubleshooting for Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson vacuum brush roll doesn't turn


The brushbar should only turn when you meet two conditions:\015\0121) When you step on the front of the machine and pull back on the handle (recline the machine in other words)\015\0122) The dial is set to CARPETS\015\012\015\ ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?


I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.


... Dyson Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Brush doesnt turn belt isnot broken - Dyson DC28 Animal Bagless Upright Vacuum


Hi there,I'm sorry to hear you're having difficulties with your DC28. It's probably best if you get in touch with us directly so we can resolve this issue for you as quickly as possible.You can call us free on 1866MYDYSON - or if you ... Dyson DC28 Animal Bagless Upright Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Motorized brush bar not turning on Dyson Vacuum


Apparent common failure is that either the thin yellow and or blue motor drive wires that run from the LH side of the vacuum where the "control board" is located down into the hinge / ball area become stretched and then fray and eventually break. Ha ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Dyson Stowaway carpet brush turning off randomly while vacuuming.


... Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum

DYSON VACUUM BRUSH WON'T TURN - Dyson DC15 Animal Bagless Upright Cyclonic Vacuum


The problem will most likely be either with the PCB under a panel on the side of the chassis, or the small wires from it that feed the front brush motor. \012\012If you are technically inclined, you can ask for more detail on the repair here: ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

Dyson DC14 animal vacuum does not turn on however the roller brush does come on.The hose was clogged and that was cleared but vacuum still will not turn on.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Brush roll won't turn on for the shark NV22L vacuum. the light on the brush roll is dark, not red or green


Atthe bottom of the vacuuam are screws to take off...two of them are near the rear wheel assembly....two of them are behind the front mini wheels (just pry the front mini wheels so that they pop out...they pop back in)Remove all of the screws. Re ... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

The beater brush on my vacuum appears to roll when I turn on the vacuum however, you only hear the actual sound of it on occasion and the vacuum is not vacuuming thread off the floor.


Greetings from GoVacuum,\015\012\015\012Your belt has probably been stretched to a point, the brush no longer spins when it touches the carpet. You probably can turn the machine over, and see the brush spinning, but it's probably stretch ... Eureka Vacuums

I have a Dyson DC33 bagless vacuum and the beater brush is not turning .. How do I get the cover off the brush to change the belt?


If you lay it down so you can see the bottom of the vacuum, there should be 3 flathead looking screws,just turn them a quarter turn or so, and that bottom should pop off so you can take the brush out and change the belt, just make sure you watch how ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

I have a canister style vacuum. The brush roll has stopped rolling on carpet. When turned over, it rolls fine. I have disassembled and cleaned out hair and that didn't work. Any help would be very much appreciated. Thank you. Martha


You need a new belt. They stretch after awhile and won't turn the brush roll under load. ... Vacuums

When vacuuming on position I, the motorized brush does not roll and light does not turn on.


Dont use brushes on wooden floors ,,,,this link is the manualhttp://www.sharkclean.com/manual/NV351_26_NV352_26_IM_ENG_SPA_101207.pdf ... Shark Vacuum. Navigator Lift-Away Bagless Upright Vacuum Cleaner NV352

Why does my Dyson Animal Upright Vacuum power light turn red when I tilt it back to vacuum? It will work if I switch it to bare floors and don't need the beater brush.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?


I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Dyson dc07 brush not turning belt is intact? - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


DC07s have two drive ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I had to empty the canister and when I put it back on and turned on the vacuum, the suction does not turn on. The brushes are rolling and the attachment suction works fine. Any suggestions?


... Eureka 431A Optima Bagless Upright Vacuum

It.s anew vacuum cleaner Dyson DC24-ball one, bought only a few months ago..but the brush rallied normally only for a few days. We washed the 2 filters but the brush never started to roll. What should do?


Hi there, its Darran at Dyson.It sounds as though you need to re-set the brush bar. It can stop rotating if it becomes obstructed. You need to simply locate the red re-set switch on the side of the cleaner head and push this button righ ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Dyson Animal handheld brush not turning - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson.We would recommend checking it for a blockage and a removing any hair or fibres from the brush bar. As the brush bar relies on the suction power of your machine, it would be worth cleaning the filter and ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?


Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum

The brush quit turning while i was vacuuming - Dyson DC07 Bagless Upright Cyclonic Vacuum


Could be some debris is caught in brush or belt broke. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Is the roller brush supposed to turn when the power is on?? the sucktion is on but the brush doesnt roll


That means that you need to replace the belt which turns the roller brush. Here is the belt you need to replace and the manual which has instructions: ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1445 seconds