Having problems with your Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum ?

Ran across shoe lace and when I pulled it out the beater bar quit rotating

\015 Ran across shoe lace and vacuum sucked it up before I could move it. the beater bar does not rotate. How can I fix it?\015

Answers :

Just cut the sholace part that you can see... it will get it into a lot of small peices and just pull out the smaler laces
If you can turn the beater by hand(when unplugged) and its easy to turn then it's the drive belt, they do not take long to burn through, and leave a horrid burning rudder smell as a clue.If its hard to turn you have jamed a piece oof lace in it.
Repair Help & Product Troubleshooting for Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Ran across shoe lace and when I pulled it out the beater bar quit rotating


Just cut the sholace part that you can see... it will get it into a lot of small peices and just pull out the smaler laces ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I ran over a shoe lace and the brush on my dyson quit rotating how do i get it going again?


Turn it off and turn it back on again and it should reset.If that dosent work you probably broke the belt.It's easy enough to replace by just removing the bottom plate and the brush and installing the new belt. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I ran over a shoe lace and now it is making a loud rattling noise


The All Floors model has a protective belt clutch system and the rattling sound means the clutch has slipped. This would have to be repaired officially by a Dyson repairer. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

While vacuuming my carpet, a corner of a throw blanket was sucked into the beater bar. I turned the vacuum off and was able to pull the corner of the throw blanket out without much resistence. I plugged the vacuum in and started it and now the beater bar isn't rotating.


Try pressing the reset button on the nozzle, probably just tripped out the brushroll motor ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Beater bar stopped after sucking up shoe lace


Hi choward40,Yah, vacuums don't particularly care for shoelaces! :>) Did you get the shoelace taken out of the beater brush?Did the shoelace go all the way into the machine?Please reply back. Thanks, ... Dyson Vacuums

Fantom Thunder vac....beater bar quit rotating - can't even move it manually....seems to be locked up.


... Fantom Vacums XT450K Upright Vacuum

Kirby Heritage II. Beater bar does not turn. One end rotates freely, but the other sticks, preventing the bar from rotating. No obvious means to disassemble the end of the bar. Is there a way to repair this, or does this require replacement of the beater bar? Did clean the front end assembly, and removed all hair, threads and similar obstructions.


The bearing is bad on the end that turns hard. You will need to purchase a new brush roll assembly. If the roller is older that 4 or 5 years, it should be changed anyway. The brush strips that scrub the carpet loose their strength after many years of ... Vacuums

I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn't any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet


Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. ... Dyson Ball DC24 Bagless Upright Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

I ran my vacuum against an area rug that has strings around it and a few strings got caught up in the beater bar. Now, the beater bar does not function- the motor runs but the beater bar does not seem to be operating. I removed the strings from the bar.


Hi,\015\012\015\012There is a switch next to the main power switch on the handle which turns the brushbar on and off. When the beater bar becomes obstructed as in your case, there is a safety feature which cuts power to the beater bar. Al ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Unit powers up but beater bar does not rotate


Have you checked the belt that drives the beater bar? ... Kenmore 22812 Bagged Canister Vacuum

I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.


I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?


... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater Bar Quit Working


Its highly unlikely you'll get a free answer on this web-site, so it's either fork over the money to these jokers or get an answer for free on another forum. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I caught a hidden shoe lace in my dyson 17 beater head....shut it of quickly....removed the lacing from around the head....loosened the three screws on the botton of the head....cleaned it out from whatever little dust there was....checked the heads belt reset the roller brush into the head...but alas no beater brush action. what to do?(I've had my dyson about5 months....HELP!. thanks, Jan Selman


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Germ Guardian GGU350TT. The Beater Bar Brush is seized up on the ends and no longer rotates. Can it be fixed or can I buy a replacement Beater Bar Brush? I've called the company and they were no help.


... Germ Guardian GGU300 Bagless Vacuum

Removing cover over beater bar for cleaning on dyson animal vacuum. Accidentally ran over mess on carpet and need to clean inside of cover and beater bar. Thanks


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater bar is no longer engaged. Caught a shirt and I pulled it out of the head. After removal, it would no longer spin when I put the vacum in the engage mode. How to reconnect the spinning of the beater bar in the head?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Kenmore 39522 vacuum beater bar keeps rotating after unit is shut off. Even unplugged it to move to another room and when I plugged it back in, the bar rotated a few more times! Has a definite clicking sound when this happens. Purchased in January 2008.


The berings or something inside might be going bad. ... Vacuums

I have a Hoover Mach 5. The beater bar will not rotate. I have taken the plate off of the bottom and sometimes it will rotate. I put the plate back on it stops. I have taken off any hair, string or anything else that may hang up the bar itself to no avail.


Replace the belts part # 38528-034 V belt and 38528-035 flat belt also inspect the belt groove on the brushroll if the new belt rides deep in the groove you will need a new brushroll. there is a tensioner for the V belt that tightens it when the hand ... Hoover Vacuums

I was cleaning the hair from the beater bar, and it popped out with the belt still attached...have tired to put it back in , but the beater bar will not rotate when the vacuum is turned on


When you put it back make sure that the ends of the bar fits exactly in the ends o the box and has to roll smoothly even when you rotate it with your hand when you try this has to be disconnected ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.


If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

The beater brush bar will not rotate. Fringe on t...


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Beater bar not rotating


Remove the screws from the bottom of the power head. ... Panasonic Kenmore Canister Vacuum Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0373 seconds