Having problems with your Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum ?

My dyson roll bar is not rotating and I have cut away any possible obstacles


Answers :

Hello. when the roll bar no longer rotates it is usually a sign that the belt has broken or stretched out. This is the one bad thing about Dyson. If it was another brand, you would go and buy a new belt for $5.00. With Dyson, they enclose the belt in a "drive belt assembly" which usually costs about $70.00. Regards, Joe
Repair Help & Product Troubleshooting for Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson roll bar is not rotating and I have cut away any possible obstacles


Hello. when the roll bar no longer rotates it is usually a sign that the belt has broken or stretched out. This is the one bad thing about Dyson. If it was another brand, you would go and buy a new belt for $5.00. With Dyson, they enclose the bel ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Possible broken belt - where do I find access to the belt. The beater bar does not rotate when i release the handle. I like this machine, but It is only 2 years old, the warranty has expired. And i must say, I am disappointed I am concerned that this article will end up in the landfill, adding one more problem for the environment.


As you do not say which type of vac ? but assume definately upright hoover/dyson or similar ? the actual belt is not difficult to renew on either model/s at this stage can only suggest you turn vac over to reveal the cover that houses the ro ... Vacuums

Kirby Heritage II. Beater bar does not turn. One end rotates freely, but the other sticks, preventing the bar from rotating. No obvious means to disassemble the end of the bar. Is there a way to repair this, or does this require replacement of the beater bar? Did clean the front end assembly, and removed all hair, threads and similar obstructions.


The bearing is bad on the end that turns hard. You will need to purchase a new brush roll assembly. If the roller is older that 4 or 5 years, it should be changed anyway. The brush strips that scrub the carpet loose their strength after many years of ... Vacuums

Is it possible to remove the brush bar from the housing of a mieleTurbobrush STB 205? The brush bar is not spinning due to been dirty and clogged and needs to be removed for cleaning. Is it possible to remove the brush bar????


... Miele 06271980 STB 205-3 Turbobrush

I have a dyson dc14. the brush bar will not rotate when the vacuum is running. the belt is attached and it will rotate by hand. when you switch from bare floors to carpet-the bar will not kick in and rotate.


\015\012Hi,\015\012Check that when you pull back handle to vacuum the clutch control knob which is located front lower left side of machine moves to drive position & is not stuck in off or park po ... Dyson Vacuums

Kenmore 39522 vacuum beater bar keeps rotating after unit is shut off. Even unplugged it to move to another room and when I plugged it back in, the bar rotated a few more times! Has a definite clicking sound when this happens. Purchased in January 2008.


The berings or something inside might be going bad. ... Vacuums

I have a Hoover Mach 5. The beater bar will not rotate. I have taken the plate off of the bottom and sometimes it will rotate. I put the plate back on it stops. I have taken off any hair, string or anything else that may hang up the bar itself to no avail.


Replace the belts part # 38528-034 V belt and 38528-035 flat belt also inspect the belt groove on the brushroll if the new belt rides deep in the groove you will need a new brushroll. there is a tensioner for the V belt that tightens it when the hand ... Hoover Vacuums

Hi. I have a DC 24 which when brush rotates makes a very loud noise. I have replaced the brush and side bar. The side bar appears very loose. The noise stops when I switch the brush rotation off. Any ideas ?


Hi there,I'm sorry to hear you're having difficulties with your DC24. If the cleaner head seems to be making an unusual noise during use, you may want to check all the parts are correctly assembled, and that the cleaner head and brushbar are ... Dyson Ball DC24 Bagless Upright Vacuum

Got a Panasonic Eco max vacuum cleaner model mc-ul952.Brush bar does not rotate when switch set on ''carpet'.Brush bar clear....rotates freely by hand


... Vacuums

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn


The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.


If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Dyson dc28 red and white lights keep flashing, brush bar does not rotate. Cleaned off bar and still the same problem


... Dyson DC28 Animal Bagless Upright Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

My new domestic Pentax cam 50 water pump is sometimes going to 0 bar and not cutting in I would like to adjust the lower pressure from 1.5 bar (22 psi) to 2 bar (30).I have a diaphram type pressure tank.


... Vacuums

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brush rolls of my Euro-Pro Shark vacuum (model-UV 210CN) are stuck; the brush is unable to roll. Does that mean I have to the roll on one end or the whole brush unit? I live in Canada and if possible let me know where I can find a store. Thank you.


... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

My new domestic Pentax cam 50 water pump is sometimes going to 0 bar and not cutting in I would like to adjust the lower pressure from 1.5 bar (22 psi) to 2 bar (30).I have a diaphram type pressure tank.


... Vacuums

Vacuum bar not rolling


Belt is busted . Need new belt . Vac comes with three additional belts. Ask your roomate belts he should have them somewhere. ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

Vax Mach 7 - the brush bar won't rotate but the belts are fine


... Vacuums

The brushes stop rotating on rugs after a few seconds then button has to be pressed to start rotating again but keeps cutting out


Not sure this is your foolproof solution to the problem, but you might give it a try to see if it solves your problem.\015\012\015\012When the beater brush starts to bind up due to debris it retards the action of the cleaner, sometimes to the p ... Dyson Vacuums

I can't get my vacuum cleaner to run. the beater bar doesn't turn. I've cut off hair and strings that have wound around the beater bar, but I can't figure out how to take off the bottom plastic thing.


... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

I inherited a Simplicity 4380ED serger. It won't cut the fabric. I changed the lower blade for a sharper one. It is lying level with the throat plate. The upper blade is smooth. The fabric edge goes along the upper cutter and rolls over from the top and goes through the serge stitching.. No cut.


A tech on this site wrote this, when a similar model as yours was "mangling the fabric":\015\012Best Solution\015\012posted on Jul 07, 2009\015\012\015\012\015\012 \015\012\015\012 ... Vacuums

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks


If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I was cleaning the hair from the beater bar, and it popped out with the belt still attached...have tired to put it back in , but the beater bar will not rotate when the vacuum is turned on


When you put it back make sure that the ends of the bar fits exactly in the ends o the box and has to roll smoothly even when you rotate it with your hand when you try this has to be disconnected ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0304 seconds