Having problems with your Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum ?

Dyson hi my dyson sounds as if something is catching when the brush goes round, it's very loud, it still has good suction. I have taken the plate of can't see anything or fell if there is anything obstructing the brush, could it be the belt?

Answers :

\015\012If the brush turns freely then you will need A new clutch unit fitted to your machine.
\015\012There are loads of them on Ebay very reasonabley priced only buy new not second hand.
\015\012Manuals are available to show you how to strip down the machine from here http://dysonmanuals.llc.nu/
Repair Help & Product Troubleshooting for Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson hi my dyson sounds as if something is catching when the brush goes round, it's very loud, it still has good suction. I have taken the plate of can't see anything or fell if there is anything obstructing the brush, could it be the belt?

Hi.\015\012If the brush turns freely then you will need A new clutch unit fitted to your machine.\015\012There are loads of them on Ebay very reasonabley priced only buy new not second hand.\015\012\015\012Manuals are availabl ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th

... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hello, I have a Riccar 8000. The belt works, the bar spins, and it will **** things up. However, it will not pick up threads and dog hair or anything from the carpeting. Mu husband took the bottom off and there were a couple of small parts on the plate. We have no idea where they belong. Could not see them in the photos in the manual. Could it possibly need a new roller? Any help would be most welcome. Thank you! Mary Simon

... Riccar Vacuums

My Rainbow SE powerhead suddenly started making a different noise that almost sounded like something was stuck. The brush bar was turning ok. I took the plate off and the belt was very hot but I could see nothing wrong. What could this be?

... Rainbow 75th Anniversary Canister Vacuum

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please

... Vacuums

Dyson i got a free dc07 animal but the brush doesnt turn it appears the belt is still on it but i cant see how to get at the belt

Hi.\015\012\015\012There are 2 belts the one is hidden under the Black casing.\015\012\015\012If you require help got to this site http://dysonmanu ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Vacuum brush Well thank you for your response but how do you remove the brush cover plate? I looked to see if I could unscrew it but i dont see any screws. I don't know how to take it off

... Kenmore 22812 Bagged Canister Vacuum

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy

The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The brush stopped revolving. I don't see anything blocking. It sucked up a corner of a rug for a split second but didn't pull anything off of the rug, ie, nothing from the rug is in there. Do these have belts? I don't see that. vicki

Although I do not share the exact same model that you have, there is a belt in the one I own. \015\012\015\012Checking it was pretty easy as the unit comes apart in a simple manner.\015\012\015\012I do not know how your unit comes apart b ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie

Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.

Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.

Model no. req ... Hoover Vacuums

My dyson dc 07 brush will not rotate. I have cleaned all hair and debris from around the brush and no change. I can not even figure out how to look and see if the belt is still attached. Suggestions?

DC07s are not easy to check the belt on, in fact depending on which exact model you have there are probably two belts.\015\012One connects the output of the motor to the clutch mechanism (one end of which has the control knob that ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?

Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

The brush-head on my Dyson doesn't spin, and there is a loud rattling sound comming from the belt assembly. I've inspected the belt assembly and everything "looks ok". What could be the problem, and how can I fix it.

Sounds like the belt is just broken friend. If you have one, just remove the brushroller from the head of the vacuum and replace ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I need instructions on replacing the belt that drives the brushes on a Bissell powersteamer pro deluxe carpet cleaner. Could the broken belt have anything to do with the suction of the cleaner?

Here is a link to the belts you need and a link to the manual:Bissell 1697-7 Manual and Replacement Belts ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

My Dyson Animal is not picking up very well in the drive position. With the hose the pick up is still very good. I have had it for 2 yrs now with very little problems. I have cleaned out all areas etc pipes, the brush underneath and cant find any blockages. The noise of the dyson is the same as usual. Could you tell me if there is a part that it sounds like it needs?

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson C07 ANIMAL is making a loud clatter noise when I push the head down. I have removed the sole plate and the brush bar is cracked so I removed it, but I understand the clutch maybe a problem also from reading other people's comments..how can I tell if it's a clutch problem also? Or... could it be just the brush bar being cracked that's causing the loud noise?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a morphy richards upright hoover model 7333 and i cant get to the belt to see if it is either broken or just come off the runners, i have lost my instructions and cant get the things apart to have a look, does anyone know anything about these hoovers? many thanks, Carina.

... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.7448 seconds