Having problems with your Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum ?

No suction I cleaned and checked all hoses, sounds like something is stuck inside, like a sock, took machine apart as much as I could and couldn't find anything. Any suggestions?


Answers :

Ok first thing to do is remove & clean the 2 piece premotor filter or purchase new.

Now remove soleplate from bottom of machine to do this rotate the 3 plastic screws to unlock position. Lift sole plate off now remove any blockagers or fluff that may be built up over the brush roller.
Remove hair from brush roll using scissors.

Check short clear hose for blockages & any damage rips or tares if it is damaged purchase new hose.

Now look at belts & rotate brush roller it should turn relatively easy if it is difficult to turn by hand remove the brush roller & pull off the end caps the axle will come out with one of the caps.
Check the roller bearings clean away dust build up replace end caps & axle spin roller holding on to end cap if freely to spin refit back on to machine.

If its stiff to rotate you will need new roller.

Now pull off the 2 inspection ports check them for bits of paper etc especialy the (U) shaped port at bottom rear of machine this can contain pens pencills stones all sorts of items that hinder the suction.

Now check the long flexi hose & metal wand for any obstructions.

If after all this machine is still not working correctly go to this site http://dysonmanuals.llc.nu/

On this site you will find Dyson service manuals covering poor suction, clutch,motor, etc.

Chris...
Repair Help & Product Troubleshooting for Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No suction I cleaned and checked all hoses, sounds like something is stuck inside, like a sock, took machine apart as much as I could and couldn't find anything. Any suggestions?


Ok first thing to do is remove & clean the 2 piece premotor filter or purchase new.Now remove soleplate from bottom of machine to do this rotate the 3 plastic screws to unlock position. Lift sole plate off now remove any blockagers or ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have an older Wega 2 group espresso machine. Looks like a date of 1992 on the group head, but not sure. This has no model name that I can find. Anyway, when I turn it on I get all lights flashing after it heats up 5 minutes or so. I do get nice steam from the wands. I drained teh tank and found a little scale, but not much. I took apart the group heads and cleaned them thinking it may be a clog there, but that doesn't seem to have worked. Also fwiw the water level float is not visible and whe


For a new fridge, need more time to maintain the required temperature of the fridge abut mainly the goods in it? So everything seems normal. The time will be reduced day by day since the goods will stay for longer time in and door opening will bec ... Vacuums

Either of my bissell porheat turbo 2x or my bissell pro heat don't have suction i would like to try and trouble shoot if i could due to the fact i am having difficulty finding a small machine repair center in my area could you possible help me or send a link which could help me find solution these machines are not more then a year and a half old if that thanks for your time and help warmest regards rebekah majors


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a Fantom 500 DX and it seems that it doesn't pick up anything anymore. It looks like machine is working well, but it doen't pick up. I would like to take to the repair guy, but I don't know where to find one. Machine is good, it might need jsu some maintenance. Please advise. I live on Long Island, NY. PLease advise. I changed the belt about 6 months ago, but all other parts are original.


The type of bagless that has sharp turns in the hose and plastic parts are easy to become stopped up. You have to follow the path of the air flow to find the blockage. ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

My Bissel Proheat smartmix bottle is emptying really fast and it doesn't seem like the carpet is even getting wet. I am just trying to do a rug in the kitchen and have filled the smartmix bottle 3x now and the rug is barely wet yet. I have cleaned out the flow indicator filter and it does not spin when I push the button like it used to. I have also checked the belt and it seems fine. It is actually a Bissel Proheat 7901/8910 (Pet) but they could not find my product. Any suggestions, I am


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My Hoover Elite model # UH30010 is making very loud noise like it is going to explode. I took it apart as best as I could. There was a lot of dirt by the roller. Could not see what was causing the back up or why the noise. Any suggestions?


... Hoover UH30010COM Bagged Vacuum

My sister dropped her roomba than brought it to me complaining it does'nt work anymore. I took it apart, cleaned everything i knew to clean,could not find anything obviously wrong so I put it back together.I charged the battery than tried it. The green light comes on when you push the clean button and it makes a little grunt noise but that's it.


Have a look at the motor brushes if there broken or poped out this is were the "grunt is coming from" the motor is trying to turn but cant? ... iRobot Roomba 4000 Bagless Robotic Vacuum

The vacuum has started making a much louder noise. like something is coming apart or is stuck/clogged. Noticed the fan type blade has several cracks, some bigger than others. could this be the problem?


Yes, this is very likely. The fan is made of plastic, because a metal fan would be so heavy that it would make the motor burn out unnecessarily fast. Sucking up things like loose change, pebbles, screws, etc. can crack the fan, and unfortunately th ... Kirby Heritage II Vacuum

Could I have a short in my cord? I can vacuum & then when I move the canister it shuts off, if I wiggle the cord it will turn back on. This last time, it just revs like a car trying to start & then does nothing. I live in a VERY remote area (80 miles from nearest Wal-Mart or McDonalds) so I know I will not be able to find someone to repair this for me. I have great doubt that I will be able to do it myself & my husband is an accountant so he is unavailable for another 6 weeks!!!!! Any suggestion


Whit the vacume plugged in and turned on start where the cord goes in to it and hold the cord whith each hand and bend it slightly. Move up the cord and do the same if there is a brake in the cord the machine will loose power until you bend the secti ... Miele Red Star Bagged Canister Vacuum

We have the bissell pro turbo with heater and we cannot get any suction for the water. took completely apart and couldnt find anything.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a miele s184 and on the same side where the hose connects to the bottom of the vacuum, the housing is very loose. It does not come apart , but it looks like it could. I cannot locate a screw or anything to tighten. Can you help.


... Miele S184 Powerhouse Bagged Upright Vacuum

The soap dispenser on my 2X is not dispensing. I wrote with this initial problem and received a reply. We did everything recommended to find a clog. To begin with, we poked holes thru the little holes on the underside with a toothpick. Next we took the machine all apart as directed and cleaned out anything that had accumulated (such as pet hair). Eventually we emptied out the soap dispenser, filled it with a hot salt water solution and let it sit for 10 min. I ran three tanks of hot water


Hello,The solution to your problem is already solved, since your soap dispenser is still under warrant,What i will suggest is that you contact the company that supply you this product and explain everything to them, it is most ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Hoover SteamVac, Model F5906-900 and the brushes won't spin. It's like something is froze up inside. I have read where the Brush Turbine might need to be replaced. Can you tell me where I can find the schematics or an internal diagram of this model so that I can take it apart. Or maybe you might have another suggestion. Thank you Pauline Newman


\015\012Hello,\015\012\015\012This is most likely the reason the for the brushes stop spinning. I've written a very detailed repair guide on how to diagnosis this problem. This will walk you through step by step with pictures, an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara


... Vacuums

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I purchased a Miele Model S518 vacuum cleaner yesterday at Canadian Tire but they could not find the manual or floor brush. I would like a manual please? and how much is a new floor brush?


... Miele Leo S5381 Canister HEPA Vacuum Cleaner Bagged Vacuum

Need the manual on how to run (put together and all) the hoover steam vac v2 (widepath) with auto rinse) we tried today and when we leaned it back (so we could run it on the carpet) water started pouring out all over the machine and got the carpet (like flooded) wet :( this one was me mom's and she passed on approx 2 1/2 years :( she always kept the manuals for everything but we caint find this one :( ... thnx


God Bless Your Mom.\015\012\015\012Hope this was helpfull to you. Sawdust46\015\012\015\012http://www.hoover.com/pdfs/manuals/F7411900.p ... Vacuums

Have Fresh Aire 2.1 about 4 years was running great then went dead. I cant find where the fuse is and have unit apart. I plug in no fan dim display shows to errors. Unit was pretty dirty at the time. I need schematic and suggestions. Also need to knpw how to remove the honeycomb from the light unit to check for blown bulb. Seems brittle and I could break it with trying to pry with augur or sharp screwdiver object.


I'm sorry this may only be a partial help. But fuses are usually very close to the motor, OR where the switch is located. Pretty easy to find by testing but you have to be or so careful you dont electricute yourself. Now if your testing shows v ... Vacuums

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

I am having problems with the roller on my Oreck DTX-1300. It turns on and off intermittantly while I'm vacuuming. I have completly taken it apart and cleaned and inspected the roller unit.(I am very much mechanically inclined) This has stumped me, I have checked the electrical from the vacuum to the floor unit, and everything else that I could think of. Question: what does the metal sensore plate on the bottom of the roller unit do?? Anything anybody can tell me, I would greatly appreciate. Cap


... Oreck DutchTech DTX1300A Bagged Canister Vacuum

I have the yellow altima vac. for a while now I can not get the darn thing to pick up properly. Or should i say keep it up.. The vac does seem to be getting everything picked up but as soon as you turn it off, you have a mess under the vac.. I have checked for clogks and can't seem to find any.. I have removed the hose, Nothing there.. And yep have removed the yellow thing inside the trash cup.. Is there anything else you could suggest??


If it smells hot, then there's a strain on the motor no doubt about it. Check the suction channel behind the sole plate and remove all of the hoses to check for a clog. It could well be that there is a clog inside the machine after the dust channel f ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Hello. first id like to thank you very much for helping me. There is no problem really. Id just like to know if i can use other soap or product to clean the rug besides the kirby evaporated dry foam.. Also how could i **** up as much water as i can?


I would only use the brand intended to be used in this machine. Home Solutions Turbo Shampoo by Aerus Electrolux. This machine doesn't **** up water, and if used according to the directions, there really shouldn't be much water on the carpet. ... Electrolux Floor Pro Vacuum

My Janome Harmony 8100 will occasionally stop and give me a System Error #1 - I cannot find anything about this error. It is a computerized machine with 70 stiches and attachable embroidery hoop. I first started getting this error with the hoop and now get it when I am just sewing. As soon as the needle goes down to the bobbin, I get the error. The machine freezes and the only way to get rid of the error is to turn the machine off. Sometimes I can get the machine going again, but now it wil


... Vacuums

My Shark lift away won't seal, sucking out the side hole, but not out of the bottom, I have taken it apart, can't find anything wrong.


... Vacuums

I've never had to change a CFL bulb like the GE 35972 in my kitchen ceiling fixture. It looks like a squared off pretzel with the socket in the middle and facing up to the ceiling. It's been in there for years -- this is a rental -- and because it's so close to the ceiling, I can't tell where to pull the pins from the socket apart without breaking it. Any instructions or suggestions? Also, my Home Depot doesn't sell it; will the pins match a different CFL, like maybe a circular one?


CFL bulbs are held in place by a friction fit, but it is a very tight fit. Grasp the CFL by the sqaure plastic base and pull firmly away from the socket. You may have to wiggle it a little, but don't try to pull it out by the globe because they are ... GE Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0883 seconds