Having problems with your Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum ?

Brush is not spinning. Belt is intact and ok.


Answers :

DC07s have two belts - one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.
I suspect the belt you are to refering to is the one from the clutch to the brush bar. Unfortuenately the other belt is hidden under a plastic cover, so you cant see if it is okay or not without some dismantling. This cover is not easy to remove and requires a Torx driver to under the securing screws.
If, after removing the cover, the other belt is okay, then you have a faulty clutch. New clutches are available on eBay reasonably cheaply, but again good tools and DIY skills are required.
Have a look at www.dysonmedic.com which has some excellent info on dismantling and repairing your machine, but unless you have access to such tools, and feel confident to tackle it, it's probably time to call Dyson or a Vacuum repairer.
Repair Help & Product Troubleshooting for Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater brush won't spin but belt is intact and ok. Brush is clean and spins freely by hand.


For your beater brush to spin, you have to meet two conditions:\015\0121) the vacuum cleaner has to be reclined (put your foot on the front and pull back on the handle).\015\0122) The clutch actuator (the dial where you switch between BEA ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brush on my dc07 will not spin while vacuuming and it also smells of burnt rubber. I cleaned the brush bar and the belt is intact...


... Dyson DC07 Bagless Upright Cyclonic Vacuum

My manual says it is DC07, but it is pink and silver in colour. I have 2 problems, firstly the brush has stopped spinning, but belt appears intact. Secondly there are tiny holes in suction pipe near brush i.e. the little section of suction pipe at base of vacuum cleaner.


Hi there, \015\012The DC07 came out in a few different variations so the colour only indicates that yours has a hepa filter. The first problem can be caused by a few different things\015\0121. the brush roller bearings are worn or siexed. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

I have a Panasonic upright MC-V574400 and the brush doesn't spin. The belt is intact. What could be the problem? Thank you Christine


... Panasonic MC-V7355 Upright Vacuum

Brushes wont spin ,even though the belt is intact


The belt can develop a worn spot. It will be intact but not spin. Replace the belt and make and remove any hair or other garbage from around the ends of the brush bar. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Brush is not spinning. Belt is intact and ok.


DC07s have two belts - one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.I suspect the belt you ar ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???


... Bissell 3130 Bagless Upright Vacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

Miele White Star SEB 204, powerhead stopped spinning. brushes are clear of debris, belt (#3854940) is not broken. Could belt be stretched so that brush head does not spin?


Yes, most likely the belt has stretch. Flat belts do this after a short time and need to be replaced when problems start with the brush roll not wanting to turn. Also check the brush roll, make sure that the ends turn freely, if not, then replace i ... Miele Vacuums

I put both belts on my U6634-900 and i can make brush spin manually, but the small belt looks to big, not fitting snugly and not turning brushes when i give it juice. Yes I have the right belts.


... Hoover U6634-900 WindTunnel Bagless Upright Vacuum

I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?


Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

We are trying to replace the belt on the bissell 89q9 model. We purchased belt 8 and got in onto the brush however the brush doesn't spin anymore. Even trying to turn it by hand doesn't work. One end of the brush has a round end to slide in (clear end piece); however the other has a rectangular end to slide in (black end) so we don't even know how it ever turned. Any suggestions?


Remove the beater brush assy & remove the\015\012shaft & brgs that go through it 7 clean out the \015\012hair,fuss ect,so it will turn\015\012\015\012You need to take your vacuum apart once a year or more\015\012to clean ... Vacuums

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?


The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

Have a Hoover model S3670 and the beater brush no longer spins. Have checked the beater belt and it is good, did find out that the light bulb in the unit was bad. Any suggestions on how to test the motor that drives the belt or determine the reason the beater brush is not working?


I usually test the motor with a cord with alligator clips on the wires, and attach them to the black and white wires on the motor ( remove the belt first ). A very common problem with this model was a short circuit developing in the short cord that r ... Hoover Vacuums

The brush does not spin but the belt is ok. The spindle at the inner end of the belt does not spin when the motor is running.


DC07s have two belts - one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.I suspect the belt you are to refering to is the one from the bar to the brush. Unfortuenately the other belt is hidden un ... Dyson DC07 Bagless Upright Cyclonic Vacuum

No spin Vacuum's brush does not spin on (low) carpet unless switched to "high" but then roller does not pick up hair on carpet. Belts are in good condition. Maybe belts are loose?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40485&thid=782631\015\012No spin\015\012Posted by erin_david on Jul 14, 2008\015\012Vacuum's brush does no ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The bar brush does not spin. I opened the vacuum head and the drive belt to the bar brush is loose. I don't see how you remove the slack from the belt.


You have to have it in the carpet setting in order to put pressure on the v-belt. there is no way to tighten up the v-belt, but i would try to replace the big flat belt. if you haven't changed this belt in over 6 months, i would change it. ( on avera ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.


- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]


You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0498 seconds