Having problems with your Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum ?

How to put the brush back in to the turquoise dyson dc07 and put the belt back on


Answers :

Repair Help & Product Troubleshooting for Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to put the brush back in to the turquoise dyson dc07 and put the belt back on


... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Ive got a dc07 dyson just changed the belt on it as i had to since then it isnt picking anything up at all nothings clogged up had it to bits and put it all back together again properly. The hose is working when i take it off its got plenty suction but when i run it along the floor it picks absolutely nothing up any ideas that i havent thought off. Thanks


Sounds like the hose underneath has become detached. Have a look and if its not that come back to me. Also can yo9u check your U Bend is still on as these can come off. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.


... Kirby Ultimate G Bagged Upright Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

Kirby sentria My roller brush won't spin belt is not broken I cleaned the Roller brush and put it back it. It put it back but it looks like the sensor balls aren't touching the plastic part underneath. The green light Doesn't turn on either. It was just working and it stop picking up out of nowhere this


... Vacuums

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?


The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

Dyson dc07 brush not turning belt is intact? - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


DC07s have two drive ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

The brushes will not turn. How do I open the unit to put the belt back on?


Hoover doesn't use belts on their steam cleaners. Either the shaft that is on top of the brush block broke off, or the turbine is bad. The turbine is what turns the brushs. ... Hoover F7220900 SteamVac V2 Upright Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Putting the turbo head brushes back on to a dyson dc14 vaccum cle


Congratulations on owning a great vacuum cleaner, it's just like mine! Here's what I do: Grab the drive belt and pull while you wiggle the brush bar into it. You have to get a little bit physical with it. The ends of the brush bar will nestle int ... Vacuums

Brush won't spin. Put it back on the ribbed belt


Make sure the driving motor (power on) is turning (without the belt attached). Make sure the brush turns freely when the belt is off (it's probably jammed with wound-up hair, thread, and other debris--remove the brush and clean/lightly oil the bearin ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike


... Hoover Vacuums

Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?


Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum

Have eureka 9734 replaced belt, put back together,brush rotates well but vacuum is not picking up anything, no suction.


It sounds like the machine is clogged. Check the port behind the belt and any and all hoses for obstructions and remove. ... Vacuums

Hello. I took the sole plate of to clean the brushes on my dyson dc14 however the brush part came out and i put it back in but since then whenever i switch it over to carpet setting it makes this really horrible clicking grinding sound its only new have only used it a couple of times.


You really need to take the sole plate back off and make sure the belt is running exactly where it's supposed to go and not looped over a piece of plastic or anything. More important is that you make sure the ends of the brush are seated properly an ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Dyson i got a free dc07 animal but the brush doesnt turn it appears the belt is still on it but i cant see how to get at the belt


Hi.\015\012\015\012There are 2 belts the one is hidden under the Black casing.\015\012\015\012If you require help got to this site http://dysonmanu ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

We have the pet steam cleaner bissell 12 amp, we tried cleaning off the brush, because the cleaner wasnt sucking up the water sufficently. a screw came out along with the belt roller, and we have no idea how to put the screw or the belt back on.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1267 seconds