Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?
Beater bar motor will not engage
\015 Replaced drive belt for beater bar, but now beater bar motor will not engage/turn on.\015
Check your clutch to make sure it's engaged. There should be a knob on the foot of the vacuum that can be turned to stop the roller.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Beater bar motor will not engage
Check your clutch to make sure it's engaged. There should be a knob on the foot of the vacuum that can be turned to stop the roller. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan
Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum
I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely
The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums
My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.
Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My beater bar makes a noise and has a crack in the motor on the beater bar and is discolored--me thinks I need a new motor for the beater bar
Sounds like you're right. New motors are available at your nearest Aerus Electrolux store. They used to charge the same amount for selling the motor and letting the buyer install it, or for installing it in the shop. Worth checking in to.\01 ... Electrolux UltraLux 2000 Bagged Canister Vacuum
Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the
Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum
My beater bar will not turn. The motor runs but
This certainly suggests the clutch has packed up, although it is possible that the belt that runs from the motor to the clutch has failed (I assume you've checked the other belt, as it's very easy to see). Changing the clutch, and the motor-to-clutch ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I ran my vacuum against an area rug that has strings around it and a few strings got caught up in the beater bar. Now, the beater bar does not function- the motor runs but the beater bar does not seem to be operating. I removed the strings from the bar.
Hi,\015\012\015\012There is a switch next to the main power switch on the handle which turns the brushbar on and off. When the beater bar becomes obstructed as in your case, there is a safety feature which cuts power to the beater bar. Al ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Brand new LG LUV200r used 10 minutes now after removing dust tank & reinstalling the vacuum motor does not run only the beater bar??? I have located wo circuit breakers both seam to be set. This suction motor should run when the switch is pressed & the beater bar should operate when the handle is moved down??? Not A happy customer will return unit to Best Buy only 100 mile round trip!!!! RDH
... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R
Beater bar is no longer engaged. Caught a shirt and I pulled it out of the head. After removal, it would no longer spin when I put the vacum in the engage mode. How to reconnect the spinning of the beater bar in the head?
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The beater bar motor doenst work when i push the bar button the bar button doesnt light up like power button how can i test bar motor or bar switch or what is the common problem wiyh this model I have 2 that dont work the same way
If it do not work ...and you already are on the second one that behaved in the same way it may be a problem with the power in your place and the cause it may be the main fuse...Im not sure where is located in this model but it has to be near the powe ... Vacuums
We have a dyson dc14 and the beater bar stopped turning, we cleaned the bar off and checked the belt and it's not broken, I know I called Dyson a year or two ago and they told me how to reset the beater bar motor but I don't remember exactly what I did, anyone know the answer to this??? thanks in advance....
Hi its Darran at Dyson.Check that the brush control dial is in the centre position when the machine is locked upright. When you release the head and pull the handle back this dial should mopve forward to the on position. Once here, the ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile
... Eureka Smartvac 4870 Bagged Upright Vacuum
My beater bar is struggling to turn. actually, it appears as though it is the motor that is struggling, as it slows down when going against the pile and the motor labours so much that it frequently fails to turn the bar until i lift it up again. the belt appears ok, and it is clean of hair etc. it is a 5 year old beam central vac. thanks, D
... Beam Industries 875 Classic Central System Vacuum
The beater bar switch on my dyson 24 gets stuck in the off position. I have to push it many many times before the beater bar engages. How can I fix this?
... Dyson DC24 All Floors Vacuum New Upright NEW
The motor running the beater bar on ny Electrolux canister vacuum cleaner runs intermittently. It runs about 2 minutes and then cuts off and automatically starts again after a 1 to 2 minute interval. I have tried taking it apart and removing the dust and grit in the beater bar attachment but with no change in operation. What would you suggest?
Check all the wiring connections to make sure they're tight. \015\0121/2. Wiring to power nozzle motor or reset switch is loose.\015\0121. Cord from power nozzle to upper wand. If the plastic portion of the wand is cracked near the co ... Electrolux UltraLux 2000 Bagged Canister Vacuum
My beater bar is not turning so the vaccuum is not picking up. The belt is not broken. The motor is working and I can see the cyclone effect in the canister. I have checked for blockages. I have cleaned the hair and string from the beater bar brushes. What should I do?
You need to replace the belt, it has probably broken. Your actually supposed to change them yearly. Here is a link to\015\012the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Again, I have a Bissel Model 3760-4. The same problem as everyone else. The beater bar will not turn. Took apart, nothing. Took to vacuum repair shop and they said it is not getting power to the motor to the beater bar. Seems like a fair number of folks are having this same issue. You would think Bissell would come up with a fix, if nothing else to save their reputation. Thanks Diane
... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum
Beater bar my beater bar won't go around, checked & the belt is fine. The motor driving the belt isn't working
... Hoover Platinum LiNX Cordless Stick Vacuum
The motor in my Powermate (Kenmore Canister 116.27614700) is whining, high pitched, but still works. A local shop told me the motor is dying (the one in the Powermate that drives the beater bar) and would cost $150 for them to repair. The machine is only 1.5 years old and I paid $300...yikes. I think I can fix it but don't understand why the foam gasket that apparently wraps around the motor costs as much as the motor. This is assuming that part 32 (ks747156) is the foam I see glued to my cur
I think you are right! Buy the motor.....use the gasket from the old motor if you can cut it off clean and just glue it on the new one.\015\012\015\012The connectors are just brass blade connectors which you should be able to get at a Ho ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
Bissell 6579-2 bagless vacuum. Beater bar siezed up. motor turns. took bar out, no movement from either end cap on bar.
1. Uing the appropriate sized drift punch, tap out the steel axle rod which passes through the beater drum.2. Each end cap houses a 608ZZ ball brg.3. Check each brg for freedom of smooth rotation. Replace both if either is seized. ... Vacuums
My Oreck beater bar is not turning. The bar is free of hair or strings, the motor is working, just the bar will not move
If the motor is working then check the drive belt. There's a door on the right hand side of the Oreck that comes off with a cross head screw. Check the drive belt isn't broken. If its intact then its a possibility that the beater bar has seized up - ... Oreck XL2600 Vacuum
Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n
From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums
Motor won't run...beater bar does
Might be the motor.but if there is a fuse it will be inside somewhere the cord comes in.if it there you will see a wire with a tubular piece of plastic in between the wire,thats where the fuse wil be.unplug it first.on the side you will see where the ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum