Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Revolving brush stopped after I got a sock snagged in it.

\015 I don't see how belt engages or how to fix.\015

Answers :

If the Dyson model has a brush bar control roller at the left hand side of the top hood then it won't be able to be repaired unless its by a Dyson call out or someone who repairs Dyson models with brush control protection. \015\012
\015\012If the model doesn't have a brush control dial then you will have to change the drive belt:\015\012
\015\012Easy to do if you flip the machine over with the beater bar looking upwards. Locate the three/two screw heads and undo with a coin. When the roller section is revealed by taking off the floor head you should replace the belt with a new one and be careful putting the beater bar in the right way on both ends. The belt will be tight brand new so expect some tension in it.
If this works for you please rate Fixya! Thanks.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Revolving brush stopped after I got a sock snagged in it.


If the Dyson model has a brush bar control roller at the left hand side of the top hood then it won't be able to be repaired unless its by a Dyson call out or someone who repairs Dyson models with brush control protection. \015\012\015\012If th ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes


Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.\015\012An instruction video for replacing the belt can be found on the below link. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Should the brushes revolve something got caught on the brushes when vacuuming up


Yes, the brushes (beater bar) should revolve. Even though the brush is spinning, you probably need to replace the belt ... Electrolux Vacuums

Revolving brush at front of machine has stopped spinning, what could be wrong


Hi there, I'm sorry to hear you're having difficulties with your DC24. If the brush bar won't rotate, you may need to reset the machine - please follow the steps shown in the video below to do this. When pressing the red reset button, you may ... Dyson Ball DC24 Bagless Upright Vacuum

The roller brush stop working


The fuse in the plug may have blow so replace it any ways ... Dyson Ball DC24 Bagless Upright Vacuum

Dyson D25 I was vacuuming and got the cord tangled inside the vacuum dyson 25. We opened it and was able to remove the cord. But the brush stopped spinning when I use the vacuum.


Hi there,Your DC25 is equipped with a sensor which shuts off the brushbar if something jams it. Please follow the steps shown in the video below to reset the machine after checking for any remaining obstructions. You may also want to refer to ... Dyson Ball DC24 Bagless Upright Vacuum

Dyson DC17 Just got it back from repair, at first use, snagged fringe for a moment, and now get no brsh action again.  Checked the brush belt and it is fine.  Is there a second belt for the clutch, and how do i get to it to check it as well?


Yes you have to take the cover of underneath three srews you will need T15 SCREW DRIVER ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The brush stopped revolving. I don't see anything blocking. It sucked up a corner of a rug for a split second but didn't pull anything off of the rug, ie, nothing from the rug is in there. Do these have belts? I don't see that. vicki


Although I do not share the exact same model that you have, there is a belt in the one I own. \015\012\015\012Checking it was pretty easy as the unit comes apart in a simple manner.\015\012\015\012I do not know how your unit comes apart b ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

I have a Panasonic Performance plus MC-V5217. Something got stuck in the rollers and it stopped spinning. We've cleared the brushes but can't get it to spin. Is there a reset button?


... Vacuums

A large screw got sucked up the vacuum. Since then the motor,which I replaced probably only 12 months ago, sounds very "winey" and when you stand the dyson upright the front brush still keeps going round instead of stopping. Any ideas? David


Sounds like the clutch mechanism has somehow been damaged.\015\012\015\012Have a look at the following site which is a great source of info on faults, dismantling, repairing and re-assembling:\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

The brushes have stopped spinning. This is a


The brush spins on a bearing, you might want to get to the bearing and make to it has not cracked or broken. ... Kenmore 33923 Bagged Upright Vacuum

Hoover hu 4207/1 pet hair removal turbo brush wont revolve


Try Larryclare1's solution for a Kenmore and see if it helps. Worked wonders for both my turbo brush attachments. http://www.fixya.com/support/t1095798-kenmore_model_116_powermate_jr_stopped ... Vacuums

Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.


How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

Bissell proheat 2x carpet cleaner when the switch is turned on the brushes rotate fot 2 seconds then STOP ,, iIf I turn it off and on again ithe brushes will rotate for 2seconds and STOP again ?? brushes rotate for


Hey, sorry to hear you're having difficulty with the brushes. Here's a quick link to troubleshooting steps.\015\012http://www.bissell.com/FAQDetail.aspx?id ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Hoover Deluxe Elite Rewind vacuum has stopped working as it should. The airflow indicator snaps on almost immediately after I turn it on whether the hose is connected to the brush or not. There isn&


... Hoover Elite Rewind Bagless Upright VacuumVacuum

Took Roomba apart to clean and now the pick up brushes start and stop during cleaning. The vaccum is clean but will not constantly spin. Runs great but pick up brushes start and stop. Is there a number for Roomba? Warranty? This one is less than one year old.


You can go to www.iRobot.com . This is the roomba website. You should be able to find replacement parts, customer support, videos or the Roomba product, and more.\015\012When y ... iRobot Roomba 530 Robotic Vacuum

I vacuumed a sock and it started to smell like it was burning. i removed the sock from the brush head. now it still sucks, but the brush doesn't roll anymore. any ideas how to fix it?


Change your belt. ... Electrolux Vacuums

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

I removed the revolving brush to remove a jammed piece of debris I had picked up and after putting brush back, it no longer revolves


Reattach your belt properly and the beater will function.\015\012\015\012Thanks for your interest in FixYa.com ... Vacuums

The brush vibrates for 30 seconds, then stops. If I depress the on/off button a couple of times it strats again, but stops after 10 seconds, and so on continously. It does it too with a new brush and with a new toothbrush.


Your battery is not getting charged properly, mabey you need to clean contacts or the life of the batterys are over ,time for new ones, if they are replaceable if not fork out for a new unit. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0518 seconds