Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Cannot turn off the vacuum

\015 Hi! I have a DC 07 dyson, and it has been a dream, until now. The problem is that the power switch is not working. Luckily, it is 'jammed' on the 'on' setting, so at least I can still use it! However, to turn it off, I must unplug it!!! Does anyone know how to solve our problem? Thank you in advance!\015

Answers :

I've read about the same problem with 3 Dysons in the past 10 minutes. One owner said a new switch (which is what you need) would cost half a new machine; which is way beyond ridiculous because a on off switch should be designed to last beyond the rest of the vacuum. I suggested if it were mine I would go to Home Depot and buy a toggle switch and either put it in or have someone put it in. Have you called a dealer about this. They may have enough complaints that to avoid bad publicity they would fix it free - if they were smart.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I own a Halo vacuum cleaner and I cannot get the wheel to turn, the belt is on securely but it still will not turn, what am I doing wrong?

... Halo Vacuums

I cannot seem to replace the beater bar on my Dyson - it seems to spin OK, but when I turn the vacuum back on and turn it to the 'Carpet" position, it makes a noise that is unbelievable. What's up with that? The belt is intact.

Sounds like its the clutch to me if it sounds like a rapid clicking and you have a large knob on the side of the cleaner head it is going to be the clutch this is a hard part to changed without the know how to do it and it is very easy to break the o ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

A small thin antenna cord on my radio got sucked up, and I immediately turned my vacuum off and easily puled out the small cord, Afterward the brush on the vacuu would notrotate.. The belt is not broken on the vacuum is not broken. My husband cannot figure out what the problem is

Hi Susan. There may still be a piece of the cord in the brush roller bearing. Check the ends of the brush and have a look. If its clear the belt is probably strethed. An easy way to test this is to turn on machine a put you hand against brush, if it ... Riccar 8955 Upright Vacuum

I have a kenmore vacuum model #116.28614801 and it just stopped working. When I plug it in nothing happens. I cannot get it to turn on do you have a manuel for this vacuum?

... Kenmore Vacuums

Cannot turn off the vacuum

I've read about the same problem with 3 Dysons in the past 10 minutes. One owner said a new switch (which is what you need) would cost half a new machine; which is way beyond ridiculous because a on off switch should be designed to last beyond the re ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I cannot get my beater bar to turn - Kirby G4 Bagged Upright Vacuum

Manual on how to attach the nozzle - HERE. Or you may watch the video on the bottom of the home page on goodvac.comGood luck,Rocky ... Kirby G4 Bagged Upright Vacuum

The ON/OFF switch does not work. Unable to turn off vacuum without unplugging from wall. After removing handle, the ON/OFF switch is in ON position, but cannot be toggled to OFF position. Please assist. Thank you.

Replace the switch. Part number 28161067 ... Vacuums

I have owned my kirby sentria for 2.5 years and have had no problems until now. The vacuum still works but I cannot lower it all the way down or the light will turn off and it will start to smell like something is burning inside. I use it on the 2nd or 3rd setting with no problem. I have changed the belt and cleaned all the hair and strings that were on the roller but it still has this problem.

Kirby has a 3 yr back to base guarentee so contact ur local rep or kirby direct and thy will sort it all from there, hope this helps :) ... Kirby Vacuums

I just purchased a Sebo Airbelt D canister vacuum. I plugged it in and used it for ten seconds then turned it off, retracted the power cord and now cannot get the power cord out of the machine. Did I not spend enough money to get a quality product? Does anyone have any idea how to get the power cord out without breaking the machine?

... Vacuums

Cannot get it to turn on - Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi, \012\012This could be because of 4 reasons.\012\0121. Fuse in plug has gone - Check this first\0122. Switch has gone - Unlikely\0123. Powercable is disconnected from the switch\0124. Motor has failed ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a TriStar LEC vacuum and today I turned it on and for a split second the motor whirred and then nothing. Now it won't come on at all. I cannot find any way to access the motor.

How do i replace the power cord on my lec tristar vaccum? ... Tristar Vacuums

I cannot charge my two year old electrolux pronto. I purchased a brand new hand held vacuum for it, but even the new one does not charge. When I plug in the cord nothing happens. If I turn on either the long handle or the portable unit within the long unit, the blue charging light comes on for a few seconds, then out. This tells me that the circuit is intact without a broken wire somewhere. I took it all apart carefully and could see nothing broken or out of place. On re-constructing it, it

It must be the charging transformer. We have already ruled out the vacuum unit. Unfortunately the transformer is not a serviceable part, and will need to be replaced. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

Possible broken belt..brush doesn't turn on Sanyo Revo SC TA3000 vacuum. Cannot find manual.

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=748077\015\012Generic problem for all Vacuums\015\012Possible broken belt. Brush doesn't turn\015\012Po ... Vacuums

The wand will not stand up on its own when attached to the vacuum head. I had earlier models which did not have the adjustable height and this was not a problem--I simply turned the wand to the side. But I cannot do it on with this wand. Any solutions?

Hello. There is a small part on that wand which enables it to stand up on it's own. It sounds like yours is worn or broken. Take it to your local vacuum repair store and they will have you back up and standing in no time. The part is about ten do ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Samsung sc8442 vacuum - has lost its suction and makes a meduim to high pitched humming noise if turn up above halfway on the suction. this also makes the red light come on. I've cleaned the filter and checked around a bit but cannot find out why it's doing it...?

There are several filters. when you take the dust box out, you need to clean this filter as wellhttp://www.4ourhouse.co.uk/cgi-bin/finder.pl?ftype=443401&brand_change=&section=0&path=&hb=0&brandset=9925&model=10689 ... Samsung Vacuums

My Infinity Shark vacuum has lost suction. The pitch sound changes very soon after turning it on. I believe the lower hose is clogged, and I cannot get the body cove unattached where the hose bends upwards into the chamber. So much for their claim of never losing suction!

... Vacuums

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio

Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being

Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug

... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?

... Vacuums

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

I was using my easy flow central vacuum, and shut it off. When I went to start it up again 5 min later, it would not turn on. I emptied out the filter, and reset the switch. When the reset button was pushed, it started up the vacuum, but the vacuum was not turned on in the house. It can only be turned on from in the garage and not on the actual hose. What is going on?

... Easy Flo EF2300 Central System Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.

When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a Eureka Power Plus vacuum, model 4702, type A. To start off, it never really had great suction. Marginal at best. Then today I was vacuuming and smelled something burning and turned off the vacuum. At that point, smoke started pouring out from the bottom of the vacuum so I layed it on it's side and the smoke cleared but I never found the source. Is it safe to turn on again after I let it cool down or is my vacuum "shot?"

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0955 seconds