Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

The vacuum suction still works but the brush wont turn. It still looks like the belt is intact and attached properly.

Answers :

The problem with Dysons is that the belt breaks and sits in position.
If you can turn the brush by hand, with little or no resistance then I would say the belts broken.
If in doubt take the cover off and look.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The vacuum suction still works but the brush wont turn. It still looks like the belt is intact and attached properly.

The problem with Dysons is that the belt breaks and sits in position.If you can turn the brush by hand, with little or no resistance then I would say the belts broken.If in doubt take the cover off and look. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.

Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?

... Kenmore 34722 Grab-N-Go Upright Vacuum

Upholstery attachment The nozzle doesn't spray properly, the water just pours out (not alot) instead of spraying. It also has very low suction. The upright part seems to be working fine. I cannot figure out how to take it apart so I can look for a clog, when I look into the hose I don't see anything.

May have a problem in the noozle asm on the hose. Hose part #90001335. \015\012 \015\012 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.

Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum

No suction i have been using mine for like a year or so. today i went to use it and then no suction. the water comes out but it wont **** it up. I haven't had any problems till now. I cleaned the little red filter but still nothing. I dont wanna take it apart with out knowing what im looking for.

I had exactly the same problem with my five-year old my Bissell 7920, and it's probably a broken pump belt.  See page 19 of your instruction manual for how to replace.  The Bissel ProHeat belt accessory pack costs $3.99 and you get a pump b ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I own a Miele S5210 vacuum cleaner which has stopped working. It looks like the dust bag wasn't fitted properly and the machine is very dirty and the filters are completely clogged. I've cleaned it up as best I can and have replaced the filters but it still won't operate. How can I get inside the casing to clean the inner motor compartment? Thanks Tom

... Vacuums

I have a Hoover Windtunnel Model U573-960, the belt turns the bar still has alot of life on it. I have very little to no suction at the end of attachment hose. I replaced filters and looked for blockagaes with no luck.

... Hoover Vacuums

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?

Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

The brush does not work on my dc15 animal, there is great suction but after about 20 seconds it sounds like something has got blocked in it although nothing is clogged, filters and hoses have all been cleaned but the brush still wont go round

Hi there,Sorry to hear you're having a problem with your DC15. You might find it helpful to visit the Support section of our website and follow these simple steps: ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

The suction still works but the primary floor vacuum doesn't. I checked the belt and its not broken. The engine that runs the floor vacuum doesn't engage like it used to

The belt doesn't have to be broken to affect the the way the vacuum picks up on carpet. If the belt is stretched then it will slip and not turn the roller brush properly. Here is the manual and belts you need: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!

... Kenmore 25512/ 25513 Progressive Canister Vacuum

My shop vac stopped working while vacuuming i looked at everything i could look at and still wont work tried several other outlets checked cable still nothing

Staring from the failrue of the power cord,the main plug,t he main switch each of the sections must be tested for continutiy before we can conclude.\012SInce it is clear case of power failure the voltage must reach the motor,if not back trace t ... Shop Vac Vacuums

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......

Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

Carpet attachment attachment appears to have poor/intermittent connection. When initiated, it works for <30 seconds before shutting down. Suction still works but carpet attachment doesn't. Near impossible to restart.

Mine became intermittant so I took apart the exteding wand section. I found that power is transmitted to the cleaning head through a ribbon cable which was damaged (burnt) from repeatedly adjusting the length of the wand. A new wand correct the probl ... Kenmore 25512/ 25513 Progressive Canister Vacuum

There is a shaft that comes out of the pump of my Bissell 1623-1 Power Steamer with gears on it. The belt to the brush attaches to it. When I went to change the belt, the belt was fine but the gear itself with the small shaft on it was no longer attached and just dropped out. It looks like there might have been a bushing there, but no more. Any ideas?

... Bissell Vacuums

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!

Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

My Bissell powersteamer has no spray releasing for floor cleaning. The spray attachment for upholstery is working. The tank is seated properly: The belt is attached properly. I bought this machine in Sept. 2009 and used it only 2x with no problems. It did a fantastic job. Can you help with this dilemma? Mark

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My eureka vacuum model 4341 has no suction. The belt still turns the beater bar and the power still turns on but there is no suction both underneath and when using the attachment.

... Eureka 4341 Vacuum

My Dyson DC25 animal is having issues. I believe everything is working correctly except I have realized that the mechanism which switches the hose/valve between the wand and the vacuum head isn't working properly. The two gear pieces that move the hose placement aren't close enough together, so they don't work together. It looks like there is a washer that I could potentially remove on the clear gear piece which would allow it to sit closer to the assembly. Would that work? Currently I am

... Vacuums

No suction power ,brush wont spin on carpet power nozzle. When it

You need to replace the belt that turns the brush. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1048 seconds