Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

My dyson dc07 is does not have the suction it used to. what should I do?


Answers :

You can't always wash that to get it sucking again, this might help:
\015\012
\015\012http://www.fixya.com/support/t2827418-very_little_suction_in_hose_no_tears_in
There are a couple of things you can do and it depends on whether you don't have suction from both the wand and the bottom of the
\015\012machine or just from one side:
\015\0121) First check the suction of the machine to ensure that the motor is still good - remove the canister and look for the two
\015\012openings/holes on the spine/frame of the machine - put your hand in front of the hole on the LEFT (higher than the hole on the right)
\015\012- if there is suction, continue the troubleshoot instructions, if there is no suction your motor may be damaged - call the Dyson
\015\012Helpline, they'll set you up with a repair with the closest authorized dealer in your area.
\015\0122) Check for blockages from the bottom of the machine. Remove the:
(i) U-Bend (stand behind the machine and look next to the right-hand-side wheel, it's attached with a rectangular clip next to the
\015\012long gray hose - push the clip and pull the U-Bend off, make sure its clear - if there's a blockage remove it and continue with the
\015\012blockage check to ensure that the entire machine is clear)
(ii) AI Valve (stand behind the machine and look above the right-hand side wheel, it's attached with two buttons on either side of the
\015\012AI Pipe/Valve - push the two buttons and pull the pipe up and off and make sure there is clear - if there's a blockage remove it and
\015\012continue with the blockage check to ensure that the entire machine is clear)
(iii) Refit the internal hose on the bottom of the machine between the wheels and make sure it isn't torn and has no holes in it and
\015\012that there is nothing clogged inside it - to refit the hose: Pull it off where it sits next to the wheel first - make sure that the
\015\012gray piece of rubber is still on the hose (if it isn't, pull the gray piece of rubber off the hole and reconnect it to the hose by
\015\012twisting it back on) - next, twist the hose off where it connects to the brushbar - inspect the hose and make sure you don't have any
\015\012holes in it - put it back on by twisting it onto the side of the brushbar first - then line the gray piece of plastic end up with the
\015\012hole next to the wheel and push and twist it back over the hole. Bring the machine back upright and test it
\015\0123) Check for blockages in the wand. Remove the:
(i) U-Bend (stand behind the machine and look next to the right-hand-side wheel, it's attached with a rectangular clip next to the
\015\012long gray hose - push the clip and pull the U-Bend off, make sure its clear - if there's a blockage remove it and continue with the
\015\012blockage check to ensure that the entire machine is clear)
(ii) Wand - take the wand off the back of the machine - put one hand on the wand handle and one hand on the gray hose - pull the
\015\012handle and push the gray hose down, you'll see a metal rod being exposed, push the hose until it clicks into place - press the
\015\012half-moon shape button with a picture of a lock on it (found on the solid gray plastic end of the flexible hose) and separate the wand
\015\012competely - point the wand into the air or at a source of light (please don't point it at the sun) and look through the metal rod part
\015\012- the handle is bent but you should still see some light coming through the other end - if you don't, there is a blockage in the wand
\015\012- use a long object like a stick or a metal hanger to remove the blockage
(iii) Hose - no need to remove it - just stretch it out and make sure that there are no dark spots in the hose (those would be
\015\012blockages) - you can also through the top of the hose - if you don't see the ground at the bottom there is a blockage in the hose
\015\0124) If no blockages are found on the machine at all:
(i) wash the filter in cold water and leave it out to dry for at least 24 hours
(ii) blow out the cyclone from the bottom (open the door on the bin door - you can now look into the cyclone) - blow it out with an
\015\012air compressor or a leaf blower
(iii) Wipe all the small holes off on the cyclone with a dryer sheet
\015\012When the filter is dry, test the suction again. If there still is no suction on the machine, call the Dyson Helpline, they'll set you
\015\012up with a repair with the closest authorized dealer in your area.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson DC07 shuts down after 5-10 minutes of use and horrible suction!


I have had this problem on two dysons and have solved it by replacing the so called lifetime pre-filter. The problem is not the washable blue sponge but the material gauze filter in the plastic surround. \015\012\015\012To see if this i ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson DC07 and it has lost suction. I have checked the belt, cleaned the circular filter and emptied the dirt chamber. The hose still has plenty of suction but I can't use the hose the vacuum the entire house.


Here are some things you can check.First you need to see if the problem is with the suction or agitation.If the suction on the hose for using the attachments is low you either need new filters a new cyclone(they are not cleanable) or it is clogg ... Dyson DC07 Bagless Upright Cyclonic Vacuum

There is no suction when using as an upright - Dyson DC07 Bagless Upright Cyclonic Vacuum


Detach the hose from power nozzle and check PN for clog. This is the most likely problem if the accessory tools work with the vacuum. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

No suction when using the hose - Dyson DC07 Bagless Upright Cyclonic Vacuum


Does the vaccuum rev higher when the hose is on? If so, there is something lodged in the hose. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson dc07 is does not have the suction it used to. what should I do?


You can't always wash that to get it sucking again, this might help:\015\012\015\012http://www.fixya.com/support/t2827418-very_little ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Why does my dyson dc07 vacuum smell so bad when i use it? I have washed the filter so it is not that problem. The smell is of a dusty variety the suction is fine but I would like to eradicate the bad odour.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson seems to have lost its suction therefore is not picking up anything yet i have found that when my dyson is standing upright it has a little more suction but nothing like how it use to work. This has only happend in the last 2 weeks. I sanded a floor & though the sander picked up majority of the dust i did use the dyson to pick up the excess and it is since then that my dyson has not been working to its full potential.


Hi there,\015\012\015\012Sorry to hear you're having a problem with your DC07. You should be able to resolve the issue by following these simple steps: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson dc07 wont work using the hose i have


Theres a o ring when u tilt the dyson from upright to 45 degree you will see it its either come off or the plastic housing that it sits in is not inline ..mark ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I just bought a used Dyson DC07. Works good but


Hi its Darran at Dyson.From your description of the problem, it sounds as though the wand/hose is blocked. To test this, please remove the wand from the machine and switch on, testing the suction from the top of the wand handle. If the ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!


I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was f ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Suction using dyson normally is fine,but when using tools its as if the suction has reversed and there is no suction for the tools


... Dyson Vacuums

Dyson DC07 loss of suction


Hi.\015\012\015\012Check brush roller is spinning when vacuuming.\015\012Check short clear hose under machine for rips & blockages.\015\012\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Ive got powerful suction from my wand when i am using my dyson upright, so the suction on the bottom not good


... Dyson DC07 Bagless Upright Cyclonic Vacuum

No suction on dyson dc07 - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Hi my dyson dc18 has great suction from wand but when you got to use the vac for floors little suction but wand still got suction even while vacuming floors is it suposed to stop suction from wand


My Dyson dc18 had the same symptoms. The wand worked well and the floor bar had no suction. After removing pieces & shoving my fingers into the machine (no blockage) I found the suction pipe rotates between two positions (floor and wand). It look ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Dyson hose suction strong...when using the brush bar no suction available. Have looked to see that all airways (u-bend) are clear. When engaging the brushbar the brushbar turns but no suction to floor.


Hello,There\012 are several things that this could be. Probably the most common problem\012 that we see when customers come in with this problem is actually a \012fairly simple problem to fix. Here are just a few things that this could\01 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Dyson loses suction when I use the wand & it makes a loud noise. It works fine when using it regularly on the poor, just not when I use the wand.


Check for blockages ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC14 Animal doesn't have the suction it used to. The piece in the back on the bottom - a flap it appears - stays open now, causing the machine to make a louder noise than usual. At first, if I put my hand on the flap opening it would close, allowing for normal suction. Now, it stays "open" permanently", causing the loss of suction.


Hi its Darran at Dyson.Having had a look at a DC14 here, I am unsure as to the part you are referring to. So that we can help you further, please contact our Helpline free on 0800 298 0298, between the hours of 7am - 10pm, 7 days a week. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My dyson vacuum cleaner doesn't seem to have the same suction power it used to. I have cleaned out the canister and have taken apart the vacuum head (for cleaning carpets) and it doesn't seem to be blocked but it seems to lose suction by the time it reaches the head. The suction is strong at the end of the hose (where you attach the telescopic attachment with vacuum head) Any ideas? Thanks, Irene


... Vacuums

Dyson DC07 bagless - upright mode v poor suction, wand mode ok


I suffered with a serviced but not sucking DC07, its fixed now. How? By replacing the cyclone unit via anotherbay, it was an accumulation of dust and debris in the section that is not accessible. Borrow a working cyclone if you can and check the diff ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson dc07 animal no suction


Hello,There could be a few things that would cause your Dyson to have no suction. I will give \015\012you detailed step by step instructions along with pictures on how you can \015\012diagnose this.Possible Problem \015\012#1. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I just purchased a DC07 Dyson vacuum cleaner. It is not vacumming my floor - I have hardly any suction at all. Do I need to activate something in order to initiate the suction?


With vac upright suction is sent to the hose ie top of vac handle when handle is tilted down to the user vacuum position it should send the power suction to the floor also make sure collection bin it in securely that make be the problem ... Vacuums

Loss of suction on dyson animal hose - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


There may be an obstruction in the hose. Hold it up to the light then I use a long thin broom handle to push the clogged hair through it, being careful not to split the hose. This always does the trick for me. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Can i use my dc07 on wet floor - Dyson DC07 Bagless Upright Cyclonic Vacuum


No.. It was not designed to pick up fluids.. I suggest a ved-dry vac..\015\012\015\012have a great day ! ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc07 suction when upright but no suction when tilted in operate position


I had the same issue and solved it easily.My experience is the same as the March 6th response/ When you push your foot onto\015\012the base and then recline the handle, use your toe to gently push the\015\012very front of the base down closer to the ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0633 seconds