Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?
My old dyson lost suction. Bought a new one,
\015 My old dyson lost suction. Bought a new one, now that just stops working while vacuuming - power does not go on\015
You have a 5 year warranty on your dyson...use it..call dyson and they can arrange to have it repair it for free
For your new machine that does not power on - call the Dyson helpline - your power switch may need to be replaced. They'll set you up with a repair dealer who will fix it for you.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My old dyson lost suction. Bought a new one,
You have a 5 year warranty on your dyson...use it..call dyson and they can arrange to have it repair it for free ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Dyson DC07 The plastic pre filter catch snapped on my Dyson. I have a replacement already, but can't figure out how to remove the bottom of the broken one. It looks easy enough to slide/snap the new one in but accessing the old one isn't easy. What do I need to do to get it out?
Turn your dyson over so you can get to the bottom undo the screw and then you can see the bottom of the clip a gentle tap with with a screw driver blade will knock it out and the other one slips in ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My dog chewed through the power cord on my Dyson DC15. I have purchased a new power cord and need instructions on how to remove the old one and replace it with the new one.
... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
The bin lid is broken on my dyson dc07, I have ordered a new lid but can't get the old one off, not sure how to remove the old hinges without snapping the hinge for the new lid to go into, any ideas?
Easy watch this video ... Vacuums
Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet
Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Dyson animal We bought a Dyson Animal from Sears a few years ago along with a service contract. We took it each year to be serviced. One year I took it because it lost it's suction. They sent it to the factory, but it came back still not working right. We did the same procedure over ands over many times than I can remember. I now have the cleaner in my garage and am using my old vacuum because I just can't seem to get anywhere with Sears. Please help me. We paid almost $600.00 and now it can't b
As someone who works for Sears, let me just say right now.. The service contract you bought sucks.. and does not really do anything for you. it was just a wast of money ( they have a new one now.. thats so much better because you get your money back ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I need to purchase a new one. Old one lost in move. Phillips Deep Fryer Model H6157/55 magnet power cord.
Need to go through phillips, manufacturer specific. ... Vacuums
Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1
Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums
I have a DC17 which is only one year old. Today I lost suction and called for assistance. A Dyson technician told me to pull off the wand and see if it is clear. It was clogged so cleared out the obstruction. My filter was cleaned more than 24 hours ago. The vacuum still has no suction. Is it dead, any other suggestions. Please help.
Take the hoses off and give them a good shaking.\012or get a long piece of stiff wire and gently poke through the obstruction. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a dyson dc14 that needs a new brush bar which I now have how do I get the old one off?
Hi there SmartAlec from NelsonVacuums.com.au here. There are 2 ways to get the brush out from the dc114 dyson. \015\0121. The easy way get a brush removal tool from e ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My first proheat lasted four years so I bought a new one. After I used my Pro Heat for only the fourth time my first issue occured, the gear on the pump that runs the brushes came off, so I had the one from my old proheat, I just changed the gear spindle that is screwed to the pump and fixed that problem but now it will not pump water. That is why I bought a new proheat, I could not get the old one to pump even after a new pump and made sure all lines were not cloged.
Is your new machine a 2X or like the old style proheat? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the
Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums
I have the new power on/off switch to replace the old one(Rainbow vacuum). However the new switch has 4 contacts & the old one has 6. Need wiring diagram.
Simply pair 1 each of the power head leads and motor leads on to one terminal and wire the cord as on previous switch. ... Rainbow E series Canister Wet/Dry Vacuum
Hi There I have got a Kirby 2 HG vaccum cleaner which is around 20 years old now. It was going really well until last week when one of the capacitors which are connected to the brushes blew up. There is two capacitors one for each brush. One of them completely blew to bits and the other one is still intact. My question is are they the same size and where do I get a new one from. I know it is an old machine, but I would like to fix it and get it going again. Any tips???
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=541405\015\012Generic problem for all Vacuums\015\012Hi There I have got a\015\012Posted by opfinder on Apr 24, ... Vacuums
Need a replacement on/off switch for Dirt Devil Deluxe Model 8201 (more than 12 years old). We have the old one out. We just need a new one to replace it. Where can we get one?
... Dirt Devil Vacuums
My Dyson Root 6 made a loud banging sound, and now its motor emits a strong burning smell every time it's switched on. It runs for a second or two, making a lot of noise, and then stops. (Just bought a new battery for it, too - what a drag...) It's off warranty, and Dyson wants almost as much to fix it as a new one would cost. Is my Root 6 e-waste, or is there anything that can be done for it?
... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum
I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?
There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
I have a very old Greenfield garden tractor, a very early 5hp one. The blade chutch facing has worn completely. I can't source a new facing for it. Any ideas on where i can buy clutch facing material so that i can cut a new one.?? The clutch facing is 150 mm od, 100 mm inside, and 3 to 4 mm thick.
Just a thought, motorcycle shop or transmission shop? ... Vacuums
I need to replace the brushbaron my DC17 Animal model Dyson. It's almost four years old. I can't find the correct part number on the Dyson Website and I can't seem to find a Dyson repair center in Albuquerque, NM. What are my alternatives? If I can't service this machine without returning it to Dyson, I won't ever buy another one.
Hi,\015\012\015\012The original Dyson part number for the brush bar (often called brush roll) is: 911961-01\015\012\015\012If you type the above part number into Google Products (click link below) you will get a list of suppli ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dyson 28 airmuscle... carpet level selectors will not stop blinking... I have tried all selectors to see if an adjustment helps It has not lost section but the blinking light tells me something is up... I have two vaccumes one for upstairs and one for downstairs. all same carpet in the house and I use the medium pile and only one of the vaccumes is having this problem
... Dyson Vacuums
My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a Dirt Devil rechargable stick vac that has lost power. Does it need a new battery and if so, where can I get one and how much is it?
... Dirt Devil Vacuums
I bought a new motor for my Riccar 8850. The new motor has 3 wires and the old one has 2. Which color wire is the ground? (or, which color wire don't I need?)
The third wire is a hot wire that goes to the headlight. ... Riccar 8850 Vacuum
I have an old Shop Vac model 3331.5. This is a 12 gallon 1.5 hight peak shop vac with a detachable blower. After many years I decided to use the blower feature, but have lost the lost the manual. Question; how do I attach the hoses to the blower? The motor has that cap on it the direct the flow of air in one direction and the wide hoses do not fit over it. I may be missing a part, but I would think the directional cap would have to come off anyway.
Remove the cap that directs the air and insert the hose in there. ... Vacuums
Panasonic NN-SD776S microwave Start button stopped working. I know, the first thought is a bad door switch because "everyone knows a microwave should not turn on if the door is open." I am experienced with electronics, but even the timer won't start at all. Funny thing is, I had this exact model do this exact thing just over 2 years ago - troubleshot all the hardware until I was lost, finally bought a new one from Costco (June 4/08). And now 2 years later this one craps out - a 2 year timer
Hello Aaron,Since your microwave is controlled by logic, and the start button / timer portion is not working, I would start troubleshooting the power supply.Get a look at the integrated circuits that are on the circuit board, ... Vacuums