Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Brush bar dosent spin and the belt is still in tact


Answers :

Hi there SmartAlec from NelsonVacuums.com.au here. Sounds like you have a brush roller bearing or bearings problem. Undo the base plate off your dyson vacuum cleaner and remove the brush it will be toughto slide it out but can be done. Hold it in your hands and see if it turns freely if not you can try and remove the end caps (bits on end of brush) and clean it out with an air compressor or small brush.Put the caps back on and retest. If its greatly improved excellent refit and vacuum. If its not freely spining it will have to have new bearings or replace the brush complete ads they are not very dear. I can supply a brush for you to buy if you are not near a parts shop. hope this helps regards SmartAlec.
\015\012Happy Vacuuming :)
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brush bar dosent spin and the belt is still in tact


Hi there SmartAlec from NelsonVacuums.com.au here. Sounds like you have a brush roller bearing or bearings problem. Undo the base plate off your dyson vacuum cleaner and re ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

On the DC14 the brush bar is not spinning. The belt is still attached and there is suction. Any ideas ?


Even though the belt is intact it can still be stretched and worn and that would cause the brush to not turn. Here is the belt you need:Dyson DC14 Belt ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Cleaned the brush bar but still not spinning DC14 Dyson


The belt is broke. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

The bar brush does not spin. I opened the vacuum head and the drive belt to the bar brush is loose. I don't see how you remove the slack from the belt.


You have to have it in the carpet setting in order to put pressure on the v-belt. there is no way to tighten up the v-belt, but i would try to replace the big flat belt. if you haven't changed this belt in over 6 months, i would change it. ( on avera ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?


Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

The brush stopped on our DC25. Husband said sparks were coming out of the bottom near where brush is. Brush was cleaned of hair and string. Brush still does not spin. I saw no belt on the brush. Should there be one?


... Dyson DC25 Animal Bagless Upright Vacuum

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?


Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I replaced the belt, and even bought a new bar, but it STILL won't spin on my kirby g5. So frustrating! I honestly think I am doing everything right.


You probably not doing it right. Replacing the belt is one of the things you have to learn how to do it. It is not really user friendly and made very easy by design. ... Kirby G5 Bagged Upright Vacuum

I have a Bissell Lift-off Revolution Turbo vacuum and the brush doesn't spin on its own anymore. Does this mean the motor is busted because there's no noise when you press the brush button. We've just replaced the belt, hepa filter and a new brush. But its still the same. What's wrong with my vacuum?


Its probably the motor. remove the covers with a #2 phillips head screwdriver and cut the wires to the motor ( unplugged ). purchase some crimps at radio shack to resplice the wires together in the same fashion. ... Bissell Vacuums

I have a DC 37, it's 3 weeks old. The brush bar will not spin. It spins when initially turned on but stops after about 3-5 seconds. I have cleaned it but still does not work.


... Vacuums

The brush on my dc07 will not spin while vacuuming and it also smells of burnt rubber. I cleaned the brush bar and the belt is intact...


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Not enough suction going into my turbo brush so it spins. Ive cleaned it checked the belt it still doesnt spin. how to fix this problem?


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?


Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Luv300b vacuum brushes won't spin. The belt is fine but still not working. Any suggestions?


... LG Electronics Kompressor Plus Upright Vacuum Cleaner LUV300B

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

My hoover model #u6436-900 brush will not spin. I have changed both belts and still nothing. I even checked to make sure they were the right sizes.


Greetings,\015\012\015\012It maybe that the belts were not installed properly, or that the roller brush might be as well. Here's a good video that explains the proper procedure of how to replace the belts on your vacuum cleaner, as well ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Have ultra vision and have changed filter and foam filter, checked all hoses but still will not pick up. Belt is fine and brush is clean and spinning properly. dirt stays at top of filter instead of falling into canister.


My kids get mine stuck all the time :(Take the vacuum outside then:Remove the hose at the bottom and see if there is any obstructions. Also shake the hose to make sure there is nothing in there as well or take it out side and make s ... Dirt Devil Vacuums

The belt is still good but the brush is not spinning. The motor sounds fine. what would cause that?


Have you checked the brush seats???? Where the brush sits in the vacumn head,...is it clean and not full of rubbish/ debris? I mean,...is it free and you can turn the brush by hand freely? ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0876 seconds