Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Brush bar won't work

\015 When I turn on the sweeper the brush bar doesn't turn. I checked the belt and it is fine. What else should I do?\015

Answers :

The belt is usually attached to its own motor. Have you checked that the electrical plug for the motor to the electronic board is not loose? If that is okay, does the brush spin on its own when the belt is detached? If not there may be hair or fiber preventing the brush from spinning correctly. If the motor encounters too much resistance, it may have shut off because of overheating.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

MY vaccuum wont suction or turn at the brush bar. The wand works and I already checked/cleaned all the areas the instrucion manual said to.

The DC07 has a "brush control system" operated by a knob on the right side of the base. This knob has two positions: "bare floors" (or "off") and "carpet" (or "auto"). The roller will turn only when the knob is on "carpet", and even then only w ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Roller brush bar wont turn after te machine made a popping noise then just only the vaccum is now working

I had this exact problem after moving the machine by car. after opening the machine there is some dampness so suspect popping was caused by liquid mixing with electricity. The machine does have drain holes so leave it upright for a week or two and t ... Bissell 9200 Upright Vacuum

Dyson DC 28 brush bar wont spin

... Dyson DC28 Animal Upright Vacuum New DC 28 Animal

How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin

The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Our Dyson upright vaccumms beater bar wont move. the vaccumm will **** up air but the bar underneath wont move. The gears are not working property.

It could be the clutch that's causing the problem or the belt. Bring your vacuum to a local repair shop and have it look at, but it sounds like it could be either one of those problems. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a dyson dc14 how do i repair my vacum? i need to try to replace the brush bar motor or something so that i can get the brush bar to work again.i hope you can help me out

Brushbar not spinning:--\015\012Ensure brush control is set on carpets mode. Note: brushbar will only spin when\015\012the handle is reclined.\015\012To get user manual for your vacuum please click on the link mentioned below\015\012 ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

My bissell pro heat carpet cleaner is not working properly...the scrubby bar is not turning... the belt is intact and working and it is turning the knob inside but the brush bar does not turn

How are the bearings? Maybe the motor that drives the belt is burnt out. ... Vacuums

DC07 brush wont spin on bottom, took all apart and wont work

Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Beater bar brush stopped working...

Does the power head motor stop, or does the brush roll stop. If it is the brush roll stopping, replace the belt and/or the brush roll. If it is the motor, you may need to clean out around the motor, it may not be getting enough air to cool causing ... Rainbow E series Canister Wet/Dry Vacuum

Brush bar wont turn and there is no hair/string wrapped round it

... Dyson DC25 Roller Brush Fits The Ball DC 25

I need a new brush bar, The end (plastic) brokeand the brush wont roll!

You can try your local vacuum shop or look online at either eBay or amazon.com. There are also websites like govacuum.com or vacpartswarehouse.com Here is a link: ... Dyson Ball DC24 Bagless Upright Vacuum

Brush bar on Dyson DC19 doesn't work properly on carpet setting

... Vacuums

Hoover F7431-900 steam vac brushes wont work

The brushes are activated by suction, my berings and gears froze up, i took it apart, kinda hard to figure out, but not as bad as it looks. i lubed the berings and the gears, then i took an air compressor to the activation fins and let it spin, lubed ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand

In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.

If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Miele power plus brush model seb234/236 won't work and telescoping wand wont stay xtended

... Vacuums

The brush bar wont spin on my dyson dc 25... i

Hi its Darran at Dyson.Simply switch the machine off and stand it upright. Press the brush bar on/off switch once and then turn the machine back on. When you release the machine into the vacuuming position, the brush bar shoul ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks

If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

My dc-15 bush bar will not work - Dyson 909592-05 DC-15 Roller Brush Beater Bar

Head motor blown, will have to take it to your nearest good hoover repair centre should cost around 49 dyson will charge 73 ... Dyson 909592-05 DC-15 Roller Brush Beater Bar

The brush does not work on my dc15 animal, there is great suction but after about 20 seconds it sounds like something has got blocked in it although nothing is clogged, filters and hoses have all been cleaned but the brush still wont go round

Hi there,Sorry to hear you're having a problem with your DC15. You might find it helpful to visit the Support section of our website and follow these simple steps: ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Dyson dc15 bagless upright. my brush bar is not working but if you use the hose it works .

\015\012http://www.espares.co.uk/datastore/ProductManuals/350256.pdf\015\012\015\012Check the above link to see if it h ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

My brush bar won't turn - works in bare floor mode, but carpet brush won't turn when it should...

Replace the belt the belt sounds like its worn or stretched the belts turn at high rpms and get very hot and soon just ware out they work fine on floors but when it comes to carpet they slow down, i hope this works out thanks ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My beater bar is not turning so the vaccuum is not picking up. The belt is not broken. The motor is working and I can see the cyclone effect in the canister. I have checked for blockages. I have cleaned the hair and string from the beater bar brushes. What should I do?

You need to replace the belt, it has probably broken. Your actually supposed to change them yearly. Here is a link to\015\012the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0994 seconds