Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

The suction is not 100 %it hs new motor and all the tubes seem clear the 3 filters have been checked ?


Answers :

Small length of reinforced plasic tubing ( about 5 inches) viewed from the bottom may be ruptured. Look closely as it may no be that obvious.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The suction is not 100 %it hs new motor and all the tubes seem clear the 3 filters have been checked ?


Small length of reinforced plasic tubing ( about 5 inches) viewed from the bottom may be ruptured. Look closely as it may no be that obvious. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

This is a new machine I got for Christmas. All of the dirt is staying in the area where the brushes are and then falls out when you turn off the machine. I have checked all connections and the hoses seem to be clear. All filters have been cleaned and there is not dirt trapped that I can see.


... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

I am getting a lot of dog hair on the filter after cleaning one room, this is something new. I cleaned as many parts as I can. It seems like the dog hair is moving from the clear canester onto the top of the filter, any thoughts??


The cone in the tank has a black gasket make sure it hasn't slid to far up ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?


If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

My new LG Kompressor Vacuum cleaner turns itself on and off while I am using it. I have checked for clogs, but everything seems to be clear. The agitator goes on and off as well


... LG Kompressor Upright Vertical Cyclone Vacuum

Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.


... Vacuums

My versatility electrolux vacuum is 2 years old and it has lost its suction, i have replaced the filters and checked every hosing area i have access to, it seems to all be clear. I dont know what else to do, it has a higher pitched whinnig sound when it is on


It sounds like the fan blades have worn away until there's basically no air resistance, thus no air flow/suction. The whine is created by the motor turning at a higher speed due to lack of resistance. \015\012The fan wasn't covered by the wa ... Electrolux Vacuums

DYSON DC05 It just doesnt want to turn on. I switched it off, one minute later I tried to switch it back on and it didnt work. I have washed the filters, checked the tubes and everything seems ok.......any ideas? thank you, Lucie


My friends Dyson DC05 was loosing suction and then it stopped altogether one day. When she took the filters out there was black soot in them so it was obvious that the motor had burnt out. I think this happened because she wasn't cleaning the filters ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Hello, I have a Eureka 71b handheld vacuum. There is literally no suction. I checked the hose and it is NOT clogged. I thought it might be the filter so I bought a new filter. Still no filter. The rot


... Eureka Vacuums

My russel hobbs mountain breeze ir purifier has a check filter light on even though ive just put in new all 3 filters....how do you get the check filter light off??


Push the mode and set buttons simultaneously to clear the check filter message from the display. ... Vacuums

Relief valve opens I have cleaned all filters replaced filters checked all hose line for blockage everything is clear


How full is the bag? ... Kenmore Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

I have a Eureka Contour model 2900 type A upright vacuum, the roller works fine nothing clogged, took it apart motor blade is free of debris, no suction from tube and blasts OUT air from the front HEPA filter location. New bag, New belt, nothing in hose.any clues as to why this can be happenning? Air should not be blasting out of the HEPA filter.


Even with your explanation,it seems the hose is clogged.Try taking the hose off,then blow through it or pour water through it.If this doesn't do it,make sure the suction canals are going to the proper areas. ... Eureka 2900A / 2901A Contour Bagged Upright Vacuum

I have a Tetratec IN600 Plus aquarium filter which does not seem to be pumping air bubbles through the water. I have checked inside and everything looks as if it should work. The pump system seems to be working as the filter is vibrating when on, but no bubbles! Please help!


... Tetra Vacuums

Vaccum does not seem to have good suction replaced bag & hose is clear


... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum

Does the philips active carbon filter FC 8033 fit the model of vacuum cleaner I own (HR 8903/A)? My catalog says I should replace with HR 6969 but was sold the FC 8033 filter. My machine seems to be overheating and I wonder if it has anything to do with the new filter.


... Philips Vacuums

My Bissell 3920 motor is making a high pitched noise. I have cleared out pet hair from top to bottom. Cleaned the lower filter and replaced the upper filter. I Checked for blockage in the hoses and found none. The filter indicator goes green when I turn it on, but the straining motor noise persists.


Click on the link below to view the replacement motor and fan for your Bissell 3920 vacuum\015\012\015\012http://www.vacuums24x7.com/motorfan.html ... Bissell 3920 Bagless Upright Vacuum

My dyson DC24 has very poor suction - all filters clean and hoses seem to be clear. had it for just over a year


Hi there,I'm sorry to hear your DC24 doesn't seem to be picking up as well as it should be. From your description of the issue, it sounds as if there may be a blockage in the machine - to locate and remove this, please follow the steps shown ... Dyson Ball DC24 Bagless Upright Vacuum

Filters all seem clean and clear, suction is fine,but loud noise


Sounds to me it could be tha fan impellor.\015\012This is vac's etc... email us if you need to.\015\[email protected] ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Poor suction (new bag, clean filter, clear hose)


Check the impeller on the moter it may be missing a fin or two (question does it make any unusual noise or vibration ?) ... Vacuums

Vacuum My vacuum is loosing it's suction power. I've checked the belt and it's in perfect shape...I've bought a new filter cup...I've checked for clogs and there aren't any...I've cleaned the entire machine...and I still can't find the source of the problem.


You checked the belt, but I bet it has stretched and won't drive the brush roll under load like it should. Belts only last a few months the stretch and should be replaced. Iff you have suction at the hose, then it has to be down below, either belt/ ... Eureka Whirlwind 4480 Upright Vacuum

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.


The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

It leaves dirt and fluff in the rollers not in the filter. So is not cleaning properly. There is never anf fluff at all in the filter. Also the lid does not close properly and we constantly get the 'check tank' light coming on. It leaves streaky marks across the floor and seems to leave the floor too wet (hence the streaks). Look forward to hearing from you.


Is there something stuck in the air passage between the tank and inlet ... iRobot 5800 Scooba Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0891 seconds