Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

My dyson ball vac bounces when I pull it backwards. It works fine when I push it forward.

Answers :

They bounce because they spin backwards try to pull back slower.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson ball vac bounces when I pull it backwards. It works fine when I push it forward.

They bounce because they spin backwards try to pull back slower. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson ball sucks fine while moving forward, when pulled backward it leaves hair or whatever on the floor. Works fine going forward????

... Vacuums

Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900

Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have an animal dyson. The front nose dives into the carpet when moving the dyson in the forward motion, fine when pulling back. A huge amount of effort is required to move it forward. Took it to a technician and he said he could find nothing wrong. He had only short nap carpet for test. Works fine on short nap, if the carpet nap has any lenght to it like shag, the dyson severly nose dives. It's like the nose is sucked into the carpet. This problem just occured after the wife used the ho

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?

Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.

The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

G5 Kirby. Works in Neutral fine. When Drive is engaged and I push forward, the wheels do not rotate forwards, however on the pullback stroke the wheels rotate backwards. What causes this? Something is clearly in the wrong position, so a diagram showing the correct position of the part that is affected would be useful.

Hello, anjeI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ta ... Kirby G4 Bagged Upright Vacuum

My Bissell Proheat 12 amp is hard to push forward(whether on or off). There is a loud clicking noise when pushing forward and it ''jumps'' up on every loud click. It's OK when pulling backwards, sprays and vacuums up water. Belt appears OK. Thanks

I had this same problem and here is what solved it for me. On a previous cleaning session, my wife decided to take the two front screws out of the clear plastic shroud that covers the brushes in order to clean behind it. Upon re-installation, she did ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.

You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

Greetings - my Dyson DC41 animal vacuum seems to be having problems with the ball - the right side of the ball if you were to be standing behind the machine seems like it's tightening as it rolls forward, as it tightens its harder to push the machine forward. Any thoughts, any fix it ideas? Thank you.

... Vacuums

My Dewalt dc500 wet/dry vac won't **** anything up, I’ve put a piece of wire to not the float ball from moving them it work fine but if I remove the wire I stop working the float ball moves to the top like it is full of water? Can you please help?

... Dewalt DC500 Canister Wet/Dry Vacuum

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!

There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Restrictive valve moments after starting the vac the red ball rises to the top and the machine quits sucking. I turn the machine off, the ball drops, I turn the machine on, the ball rises the machine quits sucking, I turn the machine off the ball falls, I turn the machine on........etc. What am I doing wrong? It works fine and then all of the sudden it starts the same stuff again. I thought it was because the retrieving container was getting too full or the cleaning soln container was not full e

The foam filter on the bottom of the tank lid is too far up. Pull it down so you have at least a 1/4 inch gap from the top. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I had to replace the switch in my Kirby G6. It took some doing but I got in out and the new one in. I must have miss labeled the wires because when I pull backwards the clutch pushes forward. Ther

Go to kirbvacuums.com and look up your model number ,they might even have a toll free number you can call ... Kirby G6 Bagged Upright Vacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

I havethe first generation purple Dyson Animal model. The brush rotates fine, but doesn't make sufficient contact with the floor/carpet, therefore does not pick up most items on carpets (suction still works however). If I put my foot on it and push down a little, it works. However, since I'm not an accomplished acrobat, this is not easy to do. :-) Any suggestions on whether this is fixable? Or should I just save up to buy a new one?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Just purchased my Dyson Ball DC24 less then a month ago. Its great when it works. The brush does not spin. At first I was able to get it working after repeatedly pushing the brush button and fooling around with the handle position. Now nothing.

If its still undr warrenty take it back i wonder if the switch is broken or a bad connection .i hope this works thanks ... Vacuums

No power Our dyson DC07 was working fine, then we pushed the button to turn it on. It started to run then shut off and now it is like the power is no longer there. I have checked outlets and they all work. Is there a fuse of some kind in this unit?? If so, how would I get to it?

The motor will have a thermal cut out,however chech your plug fuse and the cable as it enters into the off on switch. its known to snap here within insulation..... ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.

If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Hoover Savvy The red light for the dirt finder is on when pushing forward and the green light is on when pulling it back. This happens all the time. It's like the dirt finder sensor isn't working right. It seems to be picking up good and we keep the filter clean.

Does this happen at both Dirt Finder Sensitivity settings? ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

My dyson 25 animal has lost suction from the floor portion of the machine. All the hot hair is coming off the front bottom part, by the ball. Its as if the connection of air has been disconnected. The attachment works fine, though.

You have a serious clog that must be removed. It is somewhere between the floor and the bag or where ever the dirt goes. Clear it and you will be back in business.\015\012\015\012Thanks for using fixya.com ... Vacuums

Hi...my dyson cylinder vac,DC08will not start when plugged in and switched on...after working fine yesterday...have checked plug etc. Any ideas??? Thanks.

Hi its Darran at Dyson. If the machine had been left overnight and then would not switch on the next day, then this sounds as though there may be a problem with the switch or the motor. So that we can help you further, please ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Help Our Dyson does not pull itself or self-propel, and you can't push it forward. ANy suggestions?

Dyson vacuums are not self propelled. and if you cannot push it on your carpet then the pile of your carpe is more than what the vacuum can handle. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

On my Hoover Savvy U8174-900 on carpet setting, the brush spins when I pull the vacuum towards me, but stops when I push it forward. Belt is tight and fine.

Hoover savvys have two very common problems that cause this. The first and most obvious is the belt that you checked already. Many times the belt is tight but those particular belts have teeth and should you lose any teeth on the brushroller OR th ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.

Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1085 seconds