Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?
Vacuum will not start when the on/off switch is
\015 DC07 Animal Vacum will not start when the on/off switch is pressed.\015
Try replaced power switch part no:910971-01
\015\012if unit in warranty send service for free....
\015\012if unit in warranty send service for free....
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you
Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum
I was using my easy flow central vacuum, and shut it off. When I went to start it up again 5 min later, it would not turn on. I emptied out the filter, and reset the switch. When the reset button was pushed, it started up the vacuum, but the vacuum was not turned on in the house. It can only be turned on from in the garage and not on the actual hose. What is going on?
... Easy Flo EF2300 Central System Vacuum
Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc
Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
My Dyson DC07 vacuum started to run slower after being on for a little while and then would run normally again. I have switched on today and it has just stopped. When I push the start button, on occasions it almost starts and then doesn't. I am wondering if there is a problem with the switch and if so how can it be fixed? Thankyou.
The motor running slower was the motor starting to burn out. The "almost start" is the brushes making intermittent contact with the armature in the motor. \015\012\015\012Your machine needs a new motor Pam. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha
... Eureka Smartvac 4870 Bagged Upright Vacuum
On/Off switch. When the switch is set to "Floor" setting the vacuum will not turn on. When the switch is moved to "carpet" setting the vacuum starts.
Because floor means for lanolium it may have a sensor that detects carpet or linolium ... Kenmore 35821 Vacuum
I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??
... Kirby Vacuums
The unit does not start when I turn on the switch on the handle. The power nozzel runs, but the vacuum motor does not. The reset button is not popped, there is 110volts to the unit, and I tried flicking the switch inside the unit underneath the filter with no responce.
... Electrolux Centralux Vacuum
My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t
... Hoover Vacuums
Vacuum turns on for approximately 300 seconds, then trips reset switch. ABout 2 minutes later the switch can be reset and the process starts all over again
... Broan-NuTone VX550 Bagged Central System Vacuum
BEAM model 178 central Vacuum. Motor will not start. Has power but just won't start. No click when switch is turned on. Is there any fuse to check? Could it be the relay? Any other thing to check? Thank you. Pierre
My vacuum does not start after switching bag, if the little switch is pressed in the light goes on to signal full bag even though it is empty
Check your pipes.. if the can be removed clean what you can with cold water little bit of washing up liquid. ONLY. it really sound like to me its your pipes. ... Electrolux Epic 6500 Vacuum
I am looking for a contol board for a miele s143 stick vacuum. The vacuum wont start but when I supply power directly to the motor it spins. I think the switches are OK so I have concluded it is the control board Thanks Don Kenney
You should check the cord and switch's for continuity, the boards are usually pretty reliable, you could check the board for any bad solder joints, at least that would be obvious. ... Vacuums
I have a Miele s251i vacuum that was working just fine until I umplugged it (while running) and re-plugged it in at a closer socket. When I replugged it, it started for a second and then stopped. Will not start now whether we use the on/off switch or not...suggestions? Would also like to know how to disassemble the unit so I could check out the wiring with a multitester..thanks
I just had exactly the same problem. Opened the vac, checked the circuit\012 next to the motor and it can be clearly seen that the Triac burned thru\012 the PCB. Will replace it and check again. Vac bought long ago, works \012extremely well. ... Miele Vacuums
My Miele s558 Silver moon vacuum just stops suddenly while vacuuming. I can start it again using the button on the handle of the hose. It is erratic, doesn't SEEM to be due to overheating. I read online that this may mean it need a new starter switch. What do you think?
This is caused by a circuit board problem in the hose. Unfortunately, the only way to fix this problem is to purchase a new SES 125-3 hose. The good news is that the new production hoses have rectified this problem and you will not experience it agai ... Miele Vacuums
Vacuum motor overheating. Never happened before till last nite and today. It seems to be getting hot and tripping an overload switch or something like that. Starts back up after a long cooldown. Roller brush will still come on, even though the vacuum motor will not. Any idea what may be causing that?
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dirty filter caused vacuum to swtich off mid-use. Filter's cleaned, but machne won't start again. Is there reset switch or do I need to take it in to get fixed?
... Westinghouse WST1551 Wired Deluxe Upright Vacuum
Bissell vacuum cleaner model 6579-2 start switch
... Bissell Vacuums
Vacuum will not start when the on/off switch is
Try replaced power switch part no:910971-01\015\012if unit in warranty send service for free.... ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
The vacuum only starts if I hold the switch down. When I let go, power is gone.
Take the wand out. Unscrew the 2 torx screws holding switch cover assembly. Pop that cover assembly off and the little switch under the button is probably sticking. Play with it a few times and it should start working correctly. Worked on mine. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Warning light When pressing the 'on' switch, the vacuum doesn't start. The warning light just comes on. I am sure that the socket I am using is OK- could this be the motor at fault?
Make sure the bag is not full ... Miele S318 Bagged Canister Vacuum
Is there a fuse in the hoover wind tunnel model 6425-920, the vacuum just shut off during operation and will not re start with the switch. What should I attempt? Thank you.
There actually IS a fuse/buss of sorts, if you really stretch the definition, anyways...so if your switch checked out good, and your outlet didn't fizzle out and blow a house fuse or trip a breaker, in the machine base, near the motor, there is a "Th ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
We just installed a Hoover central vacuum system. As soon as we plug it in the system starts even if the switch is off. If we disconnect the wire the system goes off. What did we do wrong?
You have either left the manual switch at the vac in the on position, or you have a low voltage short at one of your inlets in the house, or at the vac itself or where a pair of wires are connected together at a pipe junction. Carefully go back ... Vacuums
I just bought an older Kirby and it vacuums beautiful but when I put the shapooer attachment on the motor won't start. The light comes on so I know I have juice. Is there another switch for the shamooer?
There are two safety switches that must be engaged. One where the vacuum bag and shampooing tank are placed. And the other in the very front where hose, upright nozzle, and shampooing tray is attach ... Kirby Ultimate G Bagged Upright Vacuum
Handle got hot, circuit breaker was activated, now switch does not start vacuum
Hello. The cause of your hot handle must be investigated as you have a bare wire or connector which is shorting out. If you are handy, disassemble the handle assembly and look for melted rubber, a bare wire touching metal, etc. The fix is to repla ... Vacuums