Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

How do you drop it down from the upright position


Answers :

Usually a foot button or it could be on the handle. a release lever..
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I can't get my animal Dyson to drop down for the brushes to pick up...it is stuck in the upright position. It is so frustrating that I can't get it to drop to vacuum the floor.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dc07 model, cannot get it to stand fully vertical upright. It is as if something is not sliding back into position right. Don't want to force it in case something breaks. The upright of the cleaner has been dropped from time to time. Any thoughts on sorting it out?. Thanks a lot. M


Hi, Try this quick repair and see if this fixes your Dyson in terms of not going in the upright position: This is a frequent problem that we see come in on Dysons. If this doesn't fix it, please feel free to just use the clarification req ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!


... Vacuums

How do you drop it down from the upright position


Usually a foot button or it could be on the handle. a release lever.. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

It sounds fine in the upright position but when I drop the handle to vacuum there's a terrible whining sound from the front. Something's up with the roller. Can the belt go bad?


If its a loud clicking sound then it may be your clutch is bad. I called Dyson about mine and thats what they diagnosed it as. They wanted $125 to fix it. I went on ebay and bought a clutch and tool to help do the job and replaced it myself for less ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vacuum won't **** in upright position, but there is suction from the hose in the upright position


Theres a knob that switches it from floors to carpet turn the to floors.please leave feedback ... Vacuums

My 9 year old Sebo X4 will not stay in the upright position. The foot pedal no longer springs back to hold the machine in the upright position. Has a spring broken? Which part needs replacing?


... Sebo X4 Bagged Upright Vacuum

Miele s7000 I clicked my upright into sitting position and accidently bumped the foot release knob. The body fell back and now I can not get it to click back into upright sitting position. Something is now in the way of it locking into place. This happened last year and it was under warranty. it no longer is and I would like to be able to fix it myself in the future. Can you help me? Thank you. Kacee in Oregon


... Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Hoover Z 400 collapsible vacuum won't lock in the upright position. I pull the pin to change from a cannister to an upright, but the unit won't lock into position


This just happened to me. i took the vacuum completely apart and found that there is a locking plastic "tooth". this had snapped off but still it the track. the damage was bad but i was able to wash of all the lube off it and used a 2 part epoxy glue ... Hoover F5858-910 SteamVac Vacuum

My Oreck vacuum cleaner will only stay on in the upright position. If I try to recline it to vacuum, it shuts off...put it back up and it turns back on. Of course I can't vacuum in the upright position...what do I do?


It sound as if you have a short in the cord or it has come loose from the motor you can take it part by removing the four screws in the buttom of the base plate to see if any of the wires are loose. ... Oreck Vacuums

Loss of suction when using upright. Suction remains for samll tools no suction when in upright position makes funny noise but ok when not used in that position kindest regards louis


U can remove the flexi pipe by pressing the inset button,it may be bit stiff if it had not being removed before.may be something is stuck at the bottom,also remove u bend where most of the stuff get stuck. i just posted how i fixed the suction and ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

My Dyson upright suddenly won't stay in the upright position. It appears that a little rubber piece has fallen out of position.


- Stand behind the vacuum cleaner and look at the right-hand side wheel\015\012- Remove the AI PIPE (it has two purple buttons that you push together to lift it up and out - it looks like a Tuba)\015\012- Lay the handle down and look for ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?


... Dyson DC25 Animal Bagless Upright Vacuum

Brush roller does not turn off in upright position


Make sure there is not a lever to move in order to stop the brushes/agitator...\015\012if the belt makes contact with the end of the shaft the brushes will rotate...\015\012tighten all of course/and take the panel of to check behind the b ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Eureka 4870 brush won't stop turning in upright position


There will be a linkage that as come loose and not operating the limit switch to turn it off, try looking at 23. Idler Clamp Assembly on the link below. ... Eureka Smartvac 4870 Bagged Upright Vacuum

Dyson DC28 Air Muscle Vacuum that is stuck in upright position


This turns out to be an easy fix.\015\012\015\012First, get some graphite lube. \015\012\015\012Lay the vac on it's 'face'. \015\012\015\0121) On the underside of the vacuum, there is a 1/2" wide 'groove" in the ... Vacuums

Yellow Dyson handle stuck in down position will not click upright


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson won't go back into upright position to engage suction


The dyson.com website had a solution for this particular problem. Just press in a button in the area around the right wheel while lifting the rear of the vacuum up. This allows the base to roll forward enough to go back into the upright position. I ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson Ball Vac won't return to upright position


... Dyson Ball DC24 Bagless Upright Vacuum

I have a DC 17. In the middle of vacuuming the vacuum stopped working when it was in the upright position. It only works when the head is down and i am using the bar. I can not use the extension bar, becasue when I put the vacuum upright it shuts off. Where is the problem?


Hi there, it's Jack at Dyson.\012 \012 Like most Dyson vacuums, DC17's main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC25 won't return to upright position - Dyson DC25 All Floors Bagless Upright Vacuum


... Dyson DC25 All Floors Bagless Upright Vacuum

I need a Dyson DC 17 Total Clean exploded parts diagream that shows the switch assembly. There are two small springs and a small plastic part that were loose inside the switch assembly. This caused the vacuum to shut off in the full upright position which is the position you use when using the wand.


I don't have a full diagram for you, but I do have a photo of how they are meant to be assembled: ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Dyson Animal will not turn on when in upright position or when using the wand. It will, however, start when in the rug vacuuming position (leaned back).


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0321 seconds