Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Can't remove bin assembly on DC07 anymore - the latch is not releasing

Answers :

Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can't remove bin assembly on DC07 anymore - the latch is not releasing

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug

Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 cyclone release catch will not click (lock) back into position after removing the clear bin assembly to empty the bin.

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 Clear Bin Flap will not release

Important thing is that in order to get the rod in the hole, you have to squeeze the trigger while you are trying to do it. Squeezing trigger makes rod longer. All fixed! ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson animal's clear bin latch is stuck and won't release. I can't take off the bin via the outer shroud release either.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 Filter Release Catch removal

If its the part im thinking of its a small spade like catch thats glued into a hole in the chassis normally id lay the machine on its front and gently tap the old catch out with a flat end screwdriver and a small hammer be carefull its very brittle ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Foot latch is broken. need to replace with new one. how does one access to remove the foot pedal latch. By foot latch, I mean the foot lever that releases the upright to lower the handle and begin vacuuming.

It is accessed from the bottom underneath by the rear wheel. However, If there are and cracks on the pedal release socket area then the base will need replacement. parts are little cost but the unit needs to be completely disassembled. ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Want to clean shroud of DC07, have done it before, but this time (and following users manual directions) the bin release catch doesn't seem to be enough to get the clear bin off. It's so stuck together! Help?

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 Filter Release Catch removal

Yes sorry i know what mean you need to remove the motor casing to reduce the risk of breaking any parts. Lay dyson on the front and remove the bottom plate and roller bar. Now you need to remove the belt from the motor pin lay on left side look t the ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 bin trapdoor won't stay closed: The small plastic piece on the tip of the center rod on the cylone assembly broke off, so my trap door won't stay closed. Any idea how to find just that part, so I don't have to replace the entire cylone part?

You can buy that part here: Dyson DC07 Spares ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Jammed release bin latch on dyson ball - Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Hoover steam vac tank releaser latch removal - Hoover F5858-910 SteamVac Vacuum

... Hoover F5858-910 SteamVac Vacuum

The bin lid is broken on my dyson dc07, I have ordered a new lid but can't get the old one off, not sure how to remove the old hinges without snapping the hinge for the new lid to go into, any ideas?

Easy watch this video ... Vacuums

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each

Should be a pry off dot on the underside revealing a screw ... Vacuums

I'm trying to remove the power switch assembly for my Dyson DC25 so I can replace the power cable. I took out the 3 screws with a T15 screwdriver and released the top two retainter pins, but the lower half of the assmbly won't detach. Please help!

Replace the two bottom screws but don't tighten up just a few turns in will do, then using the screwdriver push firmly each screw and this will release the lower part of the cover hope this helps. ... Vacuums

Dyson DC14 Cyclone bin release latch - Vacuums

... Vacuums

Dyson Dc07 dustbin will not release


Can you tell me how to replace the bin flap on a Dyson DC07?

Hi there, its Darran at Dyson here. The plastic is quite flexible, you should be able to locate the bin base into one of the lugs on one side of the bin and then twist it slightly to locate the other lug. If you are still havi ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I cant figure out how to remove the housing cover

Hello,\015\012\015\012Here's an excellent video showing you how to replace the clutch on a Dyson vacuum cleaner. It's a moderately difficult repair, but this video really helped me the first time I had to do this repair. I hope this he ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I need to replace the idler arm assembly on a U6439-900 hoover wind tunner upright. I have the clear cover completely removed but still do not see how to remove old and insert new assembly.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I need to change a belt and cant remove the casing as carpet adjust is attached and cant see how the red knob is removed

... VAX Appliances Vax X3 Bagless Upright Vacuum

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I need to change the retractable cord in a Kenmore Model 116.228.13204 vaccum but can't figure out how to remove the housing. I have removed the bag and the two screws but the top appears to be attached under the foot pedal. How do you release it. Does the foot release pop off somehow to reveal another screw in the back of the housing?

Go to this web site, it gives you complete schematics of your model. This will make it easier to see where all screws are and what you have to remove to get to reel. http://www.searspartsdirect.com/partsdirect Just enter your model # and complete bre ... Kenmore Vacuums

Dyson DC05 Is it possible to replace the cable in a DC05 cable rewind assembly? I do not appear to be able to remove the spring housing from the rest of the assembly the disk with the cable exit hole seems to be fixed is it removable?

Yes it clips out ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0784 seconds