Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Bar not spinning

\015 The vaccuum runs and their is suction out of the hose or when it is set on ''hardfloor''. However, on the carpet setting, the little bar that spins is not spinning.\015

Answers :

The belt is probably worn or stretched. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need:

DC07 Belt Changing Instructions

Replacement belts for DC07
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater bar is no longer engaged. Caught a shirt and I pulled it out of the head. After removal, it would no longer spin when I put the vacum in the engage mode. How to reconnect the spinning of the beater bar in the head?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

Is it possible to remove the brush bar from the housing of a mieleTurbobrush STB 205? The brush bar is not spinning due to been dirty and clogged and needs to be removed for cleaning. Is it possible to remove the brush bar????


... Miele 06271980 STB 205-3 Turbobrush

Cleaned the brush bar but still not spinning DC14 Dyson


The belt is broke. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Roller bar does not spin


... Vacuums

Dc28 beater bar does not spin


This link is for manual check belt is okhttp://media.dyson.com/downloads/US/floorcare/Manuals/dc28_opmanual_usa.pdf ... Dyson DC28 Animal Bagless Upright Vacuum

I have a bissell powerforce bagless turbo. The problem is the brush bar is not spinning. I have cleaned out all the debris on the brush itself, and taken it apart to make sure nothing is blocking the


Sorry to hear you're having difficulty with your vacuum. You may want to have a Qualified Technician at a BISSELL Authorized Service Center inspect your vacuum. Here's a quick link to locating a Service Center. ... Bissell Vacuums

I have a DC 37, it's 3 weeks old. The brush bar will not spin. It spins when initially turned on but stops after about 3-5 seconds. I have cleaned it but still does not work.


... Vacuums

Miele silver moon power head brush bar not spinning but spins sometimes


... Miele Vacuums

I have a Bissell powerforce turbo, and my beater bar is not spinning, i have checked fordebris in the bar itself, but it seems one of the sides is not circle and it is getting caught on its little hole it fits into... so my question is.. Is it supposed to be circle? instead of oval shaped?


Usually the bar is driven by a belt--it may have come off or snapped and is broke. ... Bissell Vacuums

Bissell Pro-Heat 7901-1 no cleaning solution is pumped out. The flow indicator is spinning and the belt is spinning the beater bar. Have cleaned the flow indicator, checked vavles in the solution tank and water tank and they are working properly. Also checked the trigger to make sure it works okay. Any ideas?? Moody Fan


Bissell Pro Heat shampooer - Fill the soap dispenser with extremely hot water and shampoo with only water for a few minutes. There is often dried soap in the lines. Make sure that all filters are clean. Press the soap container and the water conta ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The brush bar on my brand new DC 28 has stopped spinning - it is not clogged with hair, it just stops spinning almost immediately. Is there a reset button?


If there is nothing dragging it down like clogged hair ect then usually this just means the rubber drive belt has either stretched or is too smooth to grip and properlly drive the beater bar brushes. When those happen the belt cannot get a grip and s ... Vacuums

Caught a string in the beater bar. Cleared it out but now the beater bar will not spin. The belts are intact. I had this problem before and I can not find the answer online that fixed it. It is not the belt.


Hi there,Sorry to hear you're having a problem with your DC07. Please note that the brushbar will never rotate when the cleaner is standing in the upright position, or if you've used the brush control to turn it off. If you ha ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.


The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The roller is not spinning. I took the bottom screws off but and replaced the belt but am not sure how to replace the clutch. I think that is what it is anyways, the thin silver bar that controls if the roller is spinning or not


... Riccar 8850 Vacuum

Low suction The beater bar still spins fine, but the suction seems low. I have cleaned all of the filters, but it is still too low to spin a lot of the attachments.


Hi Megan,I'm sorry to hear you're having difficulties with your DC17. If it doesn't seem to be picking up as well as usual, you may have a blockage somewhere in the machine. To check for this, please follow the steps shown in our online suppo ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Vax mach 6 brush bar does not spin properly. does not spin at all on lower carpet settings and also when it is being pushed forward


... Vacuums

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the


Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum

The bar brush does not spin. I opened the vacuum head and the drive belt to the bar brush is loose. I don't see how you remove the slack from the belt.


You have to have it in the carpet setting in order to put pressure on the v-belt. there is no way to tighten up the v-belt, but i would try to replace the big flat belt. if you haven't changed this belt in over 6 months, i would change it. ( on avera ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Beater bar not spinning, seems to be stuck but when I manually spin it, it will start but will stop and go.


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

"brush bar spins erratically"


Belt needs to be replaced, it has stretched to the point that under load, it won't turn the brush roll like it should, so I would advise replacing the belt. And while you are doing that, check the brush roll and make sure the ends turn freely, if no ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Dyson DC 28 brush bar wont spin


... Dyson DC28 Animal Upright Vacuum New DC 28 Animal

The brush bar no longer spins when I turn it on


Hi there,I'm sorry to hear you're having difficulties with your Dyson. I can't provide specific advice as you haven't stated which model of Dyson you own - but if you call us free on 0800 298 0298 (UK), or 1-866-693-9766 (US), we should be ab ... Dyson Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0345 seconds