Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

I just received an older model Dyson DCo7 animal vacuum. When it is turned on and you are vacuuming, should there be suction at the top of the handle while vacuuming the floor?


Answers :

No it should not
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I just received an older model Dyson DCo7 animal vacuum. When it is turned on and you are vacuuming, should there be suction at the top of the handle while vacuuming the floor?


No it should not ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.


Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan


Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.


You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.


Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

Dyson dc40 sucks from Hose(at the handle) while vacuuming floors


... Dyson Dc40 Multi Floor Lightweight Ball Upright Vacuum Cleaner

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Handle no longer 'locks' causing the attachment suction to engage when I'm using the floor brush.


... Dyson DC25 All Floors Bagless Upright Vacuum

Proteam Pro force 1500xp Upright vacuum... When I switch to the carpet setting I have no suction power but the beater bar is turning. If I switch back to the floors setting, the suction is excellent. Wondering if the problem is in the on/off switch?


Just undo the screws on the front part of the switch assembly, carefully check all the leads to the switch. Mine slide off all the time as the switch is poorly designed and subject to damage when the darn thing tips over (easily!!!) new switches are ... Proteam ProForce® 1500XP Bagged Vacuum

I have a kenmore model 11625512506 vacuum cleaner. The problem is when I select "floor" on the handle it does not turn on, it only turns on if I select the "carpet" function and it is attached to the Power Mate. This means that I can not use any other tool or function other than the carpet one.


... Kenmore Vacuums

My dyson DC17 will not turn on unless the handle is pulled back.(into the vacuuming position) The attachment hose will not work at all (0 suction thru it). I've checked the hose and made sure there is no obstruction. Any ideas?


Not sure if I can help, but I'll try. The DC17 has two motors: the vacuum motor and a separate motor for the brush bar. It is normal that the brush motor works only when the handle is pulled back in the vacuuming position - that's the way it's made. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Rainbow Vacuum, about 5 yrs old (bought new, no issues prior) - my 6yr old tipped it on it's side while water was in basin. Now when I turn the power on, it makes a very loud sound in the motor and you can feel the vibration on the floor. The suction still works and basin still catches dirt - the noise is just so loud and I'm not sure if I should continue use or how to fix -?


Although a wet/dry vacuum, it cannot tolerate water in the motor. Water will cause the motor to short out, which will cause the motor to act/sound like yours does now, if it continues working at all.\015\012To prevent additional problems, the ... Rainbow E series Canister Wet/Dry Vacuum

When running the 2100 Electrolux vacuum, it is stopping and starting when pulling or pushing the floor attachment. Seems like the connection at the top of the handle is a little loose or the electric tabs are loose where the hose connects. Any ideas?


Other option is that on the hose end of the electrical connection, you can use an awl on the electrical connections to bend them in slightly so they make good contact when they are automatically plugged in when you connect the wands. HOWEVER, ONLY D ... Electrolux UltraLux 2000 Bagged Canister Vacuum

My floorpiece keeps turning on and off when I try and vacuum. It almost seems like it is shorting out, but it isn't. I suspect it is something to do with the handle piece attaching to the floor piece.


You are exactly correct. \012\012What it is exactly is the hose connection to the power nozzle. The plug on the handle of the hose should be flush with the plastic piece below it. To correct this, you can open the handle and push the plug ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My epic 8000 electrolux will not power on. the red light is onat the top handle ( it does not power up) but the bottom part of the floor adapter does not light up at all nor turn on ? is there a fuse ?


If there is light on handle but the electrolux is not starting then the handle switch needs to be checked and its connections.\015\012The vacuum cleaner is operated by the controls on the handle. The handle has different switches which change h ... Electrolux Epic 3500 Vacuum

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.


... Hoover Vacuums

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio


Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being


Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

Power cut off after handle was dropped on floor while vacuuming


Connections inside the handle came loose. happens to me all the time. take the handle apart and connect the wires back. ... Oreck XL Ultra Bagged Upright Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.


... Kirby Ultimate G Bagged Upright Vacuum

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.


Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

Need Kirby Generation 3 Vacuum cleaner manual. Vacuum is not picking up dirt from floor. Seems to have enough suction to inflate the bag, but when you check the suction under the vacuum, there seems to be extremely litle suction.


If your brush roll is turning and your bag is not overly full, then the only other thing it can be is a clog where the bag connects to the vacuum. Turn the plastic part out away from vacuum and lift off to see if you have something clogging it. It ... Kirby Generation 3 Bagged Upright Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks


Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0903 seconds