Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Vacuum brushes won't turn. It still has suction.

\015 Vacuum brushes won't turn. It still has suction.\015

Answers :

That means that you need to replace the belt that turns the roller brush. They naturally stretch and wear and you should replace this belt yearly. Here is the belt you need and the manual which has instructions on how to change it:

Dyson DC07 Belt and Manual
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The vacuum suction still works but the brush wont turn. It still looks like the belt is intact and attached properly.

The problem with Dysons is that the belt breaks and sits in position.If you can turn the brush by hand, with little or no resistance then I would say the belts broken.If in doubt take the cover off and look. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Its like the roller brush won't lower and it doesn't "engage" anymore. I posted this but input the wrong vacuum model ....not sure if that matters? I can vacuum and you still see footprints on the carpet. I have suction, just no brush action, yet the brush spins....

Sorry about that, I guess I have to post this as a solution in order for the pictures to display. Here's the entire solution on a similar problem that I've answered previously. Please let me know if you need help further diagnosing the machine, I ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

No suction i have a hoover supreme wind tunnel vac and its relatively new and the suction, well......sucks. It wont pick anything up! I am extremely frustrated! I picked up a ball of fuzz off the carpet and held it under the vacuum and it still wouldn't **** it up. I then shoved the fuzz up INTO the vacuum. It fell right back out. I may as well not even vacuum. Please help!

I have found more vacuums on the way to the dump because they were full. Check. Is it full?\015\012If not the air way is clogged. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!

Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.

Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

No suction i have a bissell lift off revolution vacuum. I have cleaned all the filters and emptied out the canister made sure that the hoses are not plugged but it will not pick up unless you use the hose. the floor brush is clean and still no suction coming from under the vacuum... could you help me please

Is there a blockage in the small hose in the bottom of the machine \015\012take of the pod and you will see the small hose, \015\012Is the main hose pushed into the bottom housing ... Bissell 37603 Upright Vacuum

Vacuum brushes won't turn. It still has suction.

That means that you need to replace the belt that turns the roller brush. They naturally stretch and wear and you should replace this belt yearly. Here is the belt you need and the manual which has instructions on how to change it: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a CT600 power brush that would not power up. Thinking the motor was bad in it, I replaced it with a new CT700 power brush, I am still experiencing the same problem the power brush itself does not seem to be getting electic power, but the Vacuum unit does come on with suction.

First try connecting the power nozzle directly to the hose. If it works, the problem is due to a broken wire or faulty connection in the wands. At least one wand will need to be replaced.\015\012My guess is it's probably due to a broken or di ... Broan-NuTone VX550 Bagged Central System Vacuum

I have looked online for this vacuum but could not find it. The closest one is the Eureka 8803 but the p/n on mine says 79307. I have totally disassemble this vacuum. There are no clogs anywhere. Motor spins by turning shaft. Belt is new and turns brush. It still has absolutely no suction.

... Eureka Boss Capture 8803AVZ Bagless Upright Vacuum

Miele s7000 I first got the vacuum and used it for 20mins then the vacuum just lost the suction, the brush works but it just push the dirt around the house and I can see the dust and dirt flying around.So, I thought maybe the bag was fulled so I put the new bag in but still pushing the dirt around. What's wrong with it?

... Vacuums

I have the Dyson DC14 and its like it's not brushing the carpet anymore, The brush is spinning, but its like it isn't self adjusting to the carpet height? It still has suction, but doesn't make the same sound it used to when you'd start vacuuming. Its like it never adjusts anymore???

Hi its Darran at Dyson.It sounds as though the internal hose underneath the machine has twisted slightly. With the machine switched off, lay it on its side and look at the base. You should be able to see a small corrigated hose. Simply t ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr

Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My dc17 squeals when the brushes are rotating. I have replaced the brushes twice and the belt three times. It has been back to the factory twice and they say they have done the same thing. The suction is still there but it is getting to the point I might have to wear ear plugs to vacuum any suggestions.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The brush does not work on my dc15 animal, there is great suction but after about 20 seconds it sounds like something has got blocked in it although nothing is clogged, filters and hoses have all been cleaned but the brush still wont go round

Hi there,Sorry to hear you're having a problem with your DC15. You might find it helpful to visit the Support section of our website and follow these simple steps: ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Kenmore vacuum- no suction, brush wont turn

Sounds to me like you have a plugged vacuum. Check all the way through. ... Kenmore 22812 Bagged Canister Vacuum

Kenmore vacuum - no suction, brush wont turn

Sounds like the vacuum is clogged and putting too much stain on the agitator, so I would clean out the entire passage way for the vacuum and replace the agitator belt, you must clean out all the hoses it is clogged somewhere ... Kenmore Vacuums

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brush won't move while the vacuum is still maintaining suction.

Belt intact?\015\012\015\012Be careful if you have run the machine recently, parts may be hot to the point of burning yor fingers.\015\012\015\012Is your machine properly set for height of your carpet?\015\012\015\ ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

The roller brush is not moving the vacuum has suction it's just the roller is not moving. The belt is not broke i can see it is still intact. I was sweeping and i noticed it just stopped moving.

... Dyson DC28 Animal Bagless Upright Vacuum

Caught rug, motor overheated, the brush wont turn at all, but suction is still there ...is there something I can do to reset it?

Assume that the belt is broken to the power brush /head. Did you happen to smell burning rubber at all when the motor got stuck? The motor may have a reset on it, if it was not operating, but that is not the case, as mentioned. Look in your manual fo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush wont turn..Pressed reset still no turn - Vacuums

If the motor runs and the brush doesn't turn, the first and best suspect is the belt. ... Vacuums

I have a hoover upright vacuum 1 year old and the brushes wont spin but the attachments will still work

Change the belts and if it still doesnt work theres a problem with the motor ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

Hi. I have a Hoover Wind Tunnel Deluxe vacuum, and the rotating brush does not spin any longer, but still has air suction. Cause ? Sincereley, Teresa T. [email protected]

Could use the model number. Most use a belt, if yours does, then you may need to relace the belt, also check the brush roll. ... Vacuums

My vacuum has good suction the belt is good and i cleaned all the filters but it still wont pick up anything or pull itself

Sounds like its self propelled, if so check your belt and self propelled switch. John ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1380 seconds