Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

My Dyson Animal turns the "flipper"(?) on that I would use on my carpet, but it turns stops turning right away. It then goes on and off every 5 seconds or so.


Answers :

You need to replace the belt that turns the brush. Here is the belt you need and a manual with instructions on how to change it:

Dyson DC07 Belt and Manual
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Dyson Animal turns the "flipper"(?) on that I would use on my carpet, but it turns stops turning right away. It then goes on and off every 5 seconds or so.


You need to replace the belt that turns the brush. Here is the belt you need and a manual with instructions on how to change it:Dyson DC07 Belt and Manu ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi, my roomba560 goes one foot straight ahead, then turns right for halv a foot. stops, beeps four times, and the light goes red. I charged it up, measured the voltage to 16.6 on the battery.. same thing every time. Is it battery? i have cleaned it, gearbox, everything..


... iRobot Roomba 560 Robotic Vacuum

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.


Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio


Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

Not picking up as well as it use to seems to be blowing back out some lint and debris. Also when i turn it on after a second it goes to a different noise as if a hose is not connected right or something?


There seems to be a bad connection at one of the hoses or filters.\015\012Possibly a broken,or loose hose.Put some baking powder on the floor,\015\012and try vacumming it up,to see where the white smoke is escaping.\015\012Good luck ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Protection light the protection light on our electrolux 2100 comes on every 45 seconds and the vacuum will just stop and I have to turn off for about 1 minute to get it going again and off again after 45 sec. Please help


It might be the bag or the sensor inside the machine. ... Electrolux UltraLux 2000 Bagged Canister Vacuum

The brushes have stopped spinning altogether unless I manually reach it and turn them every 30 seconds.


That indicates a bad motor. ... Bissell SpotBot Robotic Wet/Dry Vacuum

Stops Immediately. We have a Beam Serenity model 2100 installed in the home and when the hose is inserted into the wall it turns on for a few seconds and then shuts off on it's own. Turning the handle's power switch off/on restarts the unit only to have it once again stop after a few more seconds. The canaster is clean. What could be causing this stopping issue? Thanks.


The Relay Control Board in the 2100 is bad. Replace and it should work just fine. ... Beam Industries 2900 Serenity Plus Central System Vacuum

Roomba Red 4100 goes for 5 seconds then stops


... iRobot Roomba Red 4100 Bagless Robotic Vacuum

Every time we plug in the vaccum hose into the wall recepticle the vaacuum turns on for half a second and then blows the circuit breaker. This just started a few days ago. We tried replacing the 20 am


... Dirt Devil CV950 Central System Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

Bissell proheat 2x carpet cleaner when the switch is turned on the brushes rotate fot 2 seconds then STOP ,, iIf I turn it off and on again ithe brushes will rotate for 2seconds and STOP again ?? brushes rotate for


Hey, sorry to hear you're having difficulty with the brushes. Here's a quick link to troubleshooting steps.\015\012http://www.bissell.com/FAQDetail.aspx?id ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell proheat 9200 T. The brushes engage when the handle is lowered. However they only turn for about 20 seconds then stop. If you turn the power off then on they run about 20 seconds again. It is driving me crazy!


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9200 Upright Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

When the power head is turned on it goes from green light to red light and stops. The belt is fine and there is no obstructions in the brush to stop it from turning.


This will happen only when the brush or motor does not turn the right speed \015\012make sure to pull the end caps off the brush and clean any hairs or fibers from it\015\012the motor you can try and turn it by hand with out the belt on a ... Fantom Vacums Lighting Canister Vacuum

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.


Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum

My roomba backs away from docking station then starts to go then stops and spin left then stops and spins right after a few times stops and beeps many beeps. What is the problem


It sounds like the 9-beep error. You can fix it by buying a repair kit from www.eesolutions.ca. I fixed mine in about an hour and a half. ... iRobot Roomba 530 Robotic Vacuum

My electrolux2100 every time i turn it on it stays on for about 1 min then the proctection button come on then the machine turns off i wait a second and then it turns back on and does it again what can i do


First, turn dial on top of vacuum counter-clockwise so the smallest dot lines up with the arrow. See if it stays on. If not, detach hose and turn vacuum on. Place palm of hand over intake. If it turns off, it's possible that the tubes connecting to t ... Vacuums

I have a Bissell powersteamer powerbrush that sprays for only a few seconds then stops. If I wait 20 seconds or so it will spray again for another 1 or 2 seconds. I have only used Bissell cleaning products in it and clean it every time after use. The hot water tank and cleaner tank are full.


... Bissell Vacuums

I have a bissell proheat complete 2x. When I press the trigger to spray the water, it sprays for a couple of seconds and then the pressure drops and stops spraying. I turn turn it off for about a minute, turn it back on and does the same thing again. Jose Cortez


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have the euro steam blaster s3325 when I turn it on, the steam ready **** comes on right away not heating can the heating element be replaced? thanks


There is a device attach to the heating element called a thermo fuse, this devise brakes down when it get to hot.open the machine and replace it with the same value. it is written on it.. ... Euro-Pro S3325 Handheld Steam Vacuum

My Miele S558 vacuum stops working about every 20 seconds (it used toi be every 45 secondsor so) I was told its probably a contact problem, and a replacement hose seems to be the resolution.


Make sure your bag is not full and your filters are clean and unblocked, could be over heating, hence cutting out.\015\012Also test your mains lead, wobble it when its on at the plug and the body end to see if ts cuts out ... Miele Vacuums

The unit sprays for the first few seconds after I turn the unit on and then stops spraying any water or solution. I turn it off, wait a few minutes and the same thing happens. What is going on and how can I get it to work properly?


This sounds as though the pump belt is slipping. This may be caused because the pump belt has stretched slightly or the pump is seized and will not turn. Remove the pump belt and turn the pump rotor with your fingers to see it turns freely. If ... Bissell 7901-R Clearview Proheat Plus Upright Vacuum

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on


... Miele Blue Moon Bagged Canister Vacuum

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?


I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0600 seconds