Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

How does one attach the stair vacuum attachment. It doesn't appear to fit on the wand or directly on the tube.


Answers :

It could be tight or the wrong one for that model like a dco4
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How does one attach the stair vacuum attachment. It doesn't appear to fit on the wand or directly on the tube.


It could be tight or the wrong one for that model like a dco4 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity


... Vacuums

I have an old Shop Vac model 3331.5. This is a 12 gallon 1.5 hight peak shop vac with a detachable blower. After many years I decided to use the blower feature, but have lost the lost the manual. Question; how do I attach the hoses to the blower? The motor has that cap on it the direct the flow of air in one direction and the wide hoses do not fit over it. I may be missing a part, but I would think the directional cap would have to come off anyway.


Remove the cap that directs the air and insert the hose in there. ... Vacuums

Where can i buy parts for the model C151D vacuum. any place i checked does not have that model of electrolux listed. i need the power wand attachment. i ordered one that looked like it from sears parts direct but it wasn't the proper one and they do not list the model C151D


Any Aerus Electrolux store. For the one nearest you, check the below link and follow the directions. Keep in mind that if it's too far away, they do ship. If you're close enough, they do deliver.\015\012This model is not the same company tha ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C


... Filter Queen Majestic Canister Vacuum

Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!


... Dyson DC05 Bagless Canister Cyclonic Vacuum

Telescopic wand My wife's Electrolux Oxygen has a telescoping wand that expanded and contracted. All one had to do was slide a button and the lower tube slid inside the larger upper tube. Now the button no longer moves whatever was inside to allow the expansion/contraction to happen. How do I fix this situation? The wand assembly hardly seems to be made with repairs in mind. This method of manufacturing is annoying. Thanks, Eric


... Electrolux Vacuums

I have a Flotec shallow well FP4122-08. A burglar stood on the pump this summer to gain access to my goats building (window). There's a small black tube that came off at both ends. When I put the tube back on, it shoots right back off as soon as the pump is plugged in. I don't know the name of the part (tube) to order a new one, and I don't know if it just plugs onto the fittings of both ends, or goes into the pump at the end with the round fitting on it.


... Vacuums

The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Can you tell me if Powermate Power Brush attachments are all the same for all the Sears Powermate Cannister vacuums.  That is, would one power brush attachment on a Model 116.56512690 fit one that is Model 116-22512202?  Are the connecting ports all the same size?Thanks for your help.


I think your confusing model #s ,as the 116. 22512202 is the canister model number and the model number of the powerbrush attch would be 116.52512202,but to answer your ? no it depends on which wand your useing that determans which one you can use ... Kenmore 22812 Bagged Canister Vacuum

Can the two inlet pipes be connected to one line? The central vacuum I have is probably from 1993/4. It has one exhaust pipe and two inlet pipes. It was initially under my stairs. I would like to move it and have in fact moved it to the garage but am now fitting the pipes. I would like to join the two pipes that were previously going to the two inlets into one pipe. Can I do it? Also would I then join the wires? Would I put a plate on the other inlet? THANKS. It is a SMART president's choice vac


There is no real reason why not...As long as you have enough "****" then that should be fine, you will need to "Y" join and NOT a "****" joint. ... Vacuums

S 380- power 1800 is my Miele vacuum cleaner which I purchased in May 2009. A big hole has appeared in the tube. Can I cut part of the tube and fix it? if not where can I buy a new one? I looked up spare parts company but they dont tell me if the sise is correct


Miele vacuum hoses can be found athttp://www.totalvac.com/mielehose.html ... Vacuums

I have a Kirby Heritage II Turbo and I need a user's manual, but can't find one anywhere. I have to replace the fill tube in the bag and can see the cable tie on top that holds it in place, but don't know how it's attached to the mini-emtor. If I can't replace the fill tube, will tape fix it? If I just taped it; will it hold? Thanks.


Taping usually just causes a mess. The mini-emptor has coarse threads on it that the fill tube screws on to. Occasionally there is a cable tie on the bottom which is not really necessary. If you cut the tube near the bottom, you can get hold of it's ... Kirby Heritage II Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.


Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have an electolux EL7001 canister vacuum. When I attach the large power nozzle....the one for the carpets not the small one for the floors...the nozzle is not powered unless I strap it on with duct tape. Is there some piece I can purchase that will secure the connection between the wand and the power nozzle head so that it is powered without the duct tape?thank you.


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

NO DIRECTIONS FOR HOW TO ATTACH AND USE STAIR TOOL FOR MY HOOVER


Here is the link to Hoover's manuals. I could not locate a model F5900-900 But i believe it is F5914-900. Please verify before downloading manual by checking the serial number stick for a model. Its silver and should be on the back or bottom. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The metal attachement wand keeps getting stuck


This has been a major problem for all dysons. Spray a little furniture polish on the tube and it will slide in and out better. ... Dyson Vacuums

My bissellpowersteamer clearview #3105403 strays no solution when on. the hand attachment does, I have also lost my directions and problem solving booklet to which I would like to recieve another one,


When it doesn't spray solution then that usually means that the pump belt is broken or stretched. You can get replacement belts and also view the manual here: ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??


This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

Require parts diagram to Electrolux ZT17667 - need to the entire floor cleaner attachment that fit on the end of the tube.


... Electrolux Vacuums

I do not have any suction, to the base or the wand. My brushes also do not turn. The belt appears to be attached & in good condition and there are no clogs (that I can find)


Some times there is a pan beneath the vacume and an opening there, it may be clogged there, thats not real unusual, hope this fixed it,, ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Is there a floor attachment that will fit my extention wand?


There is a \015\012 \015\012 Bissell\015\012 Tool Dust Upholstery combo part # 2031099 or you can purchase a crevice tool part number # 2031063.There is also a floor tool that ... Bissell 6594 PowerForce Bagless Upright Vacuum

DYSON DC05 It just doesnt want to turn on. I switched it off, one minute later I tried to switch it back on and it didnt work. I have washed the filters, checked the tubes and everything seems ok.......any ideas? thank you, Lucie


My friends Dyson DC05 was loosing suction and then it stopped altogether one day. When she took the filters out there was black soot in them so it was obvious that the motor had burnt out. I think this happened because she wasn't cleaning the filters ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0529 seconds