Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

No suction below when carpet mode or bare floor mode selected Lots of suction with wand


Answers :

It is probably clogged near where the floor part picks up
that is why the wand still works
UGH! i had this SAME issue with the dyson when I thought the stupid thing could **** up pine needles... (IT DOES NOT WORK ON PINE NEEDLES... note to everyone!)

Check for clogs... there's a section in the manual that outlines each part your should check. Use a screwdriver and snap off the rotating thingy to the vacuum cleaner. there's a 1.5" diameter hole there, and mine was FULL of dust and pine needles... suction is back and all is well.

Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No suction below when carpet mode or bare floor mode selected Lots of suction with wand


It is probably clogged near where the floor part picks upthat is why the wand still works ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Just got my dc33... one issue... the dial switch to control btn bare floor / carpet mode doesn't seem holding in it's position when I set to the bare floor mode... it keeps coming back to carpet mode with brush-bar activated... the dial doesn't really click to the floor mode. Any advice on this?


Hi there,I'm sorry to hear you're having difficulties with your DC33. If you're concerned that the brush control doesn't seem to be staying in position, it's probably best if you get in touch with us directly. One of our experts will be h ... Dyson DC33 Bagged Upright Vacuum

Dyson upright, no suction at bottom in carpet or bare floor mode


Hi its Darran at Dyson. It sounds as though the machine is blocked. with the machine switched off, check the base of the machnie by removing the soleplate and clearing any obstructions. With the soleplate removed, you will be able to ch ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Stripped gear noise occurs in carpet mode, not bare floor mode


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.


Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

Too much suction in bare floor mode


... Hoover Company Wind Tunnel U53019 Upright Vacuum

I don't seem to get suction on the bare floor mode


Hello,There are several things that this could be. Probably the \012most common problem that we see when customers come in with this problem\012 is actually a fairly simple problem to fix. Here are just a few things \012that this could be ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Kenmore model 116 vacuum head will roll in carpet mode but no suction, no action at all in floor mode.


Tripped overload, try resetting...Check pic.... ... Vacuums

Put in new clutch, but the brush does not seem to be lowering when you change between bare floor and carpet. Does not seem to be touching carpet when engaged. Still has good suction.


The brushroll must be broken ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I've got a Kenmore canister vacuum, Progressive 236123, and there's a burning smell from the belt side of the head--smells a lot like hot rubber. I've cleaned the agitator and changed the belt, but I still get the smell. It's stronger when I'm using "carpet" mode than when I'm using "bare floor" mode. Any ideas what the problem is?


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu


Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

My dyson DC17 has a noise in it when in the carpet mode and not when in the bare floor mode. HELP


Did you clean out the roller brush and replace the belt? If you haven't done that I would give it a try. Here is a link to the replacement belt you need: ... Vacuums

My dyson works fine in the bare floors mode but when i turn it to carpet mode it makes loud noise and wont **** up.


You need to replace the belt. Here is a link to the manual and to the belts you need:Dyson DC07 Manual and Belts ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The vacuum works on carpet mode but not floor and only when the wand is attached to the floor brush otherwise it does not work at all


Please define "works" on carpet mode" do you mean when you say it does not work at all, that it does not run, or does not have suction. This sounds like the symptom of a clogged hose with blockage like this another vac needs to be used to draw ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Hi my dyson dc18 has great suction from wand but when you got to use the vac for floors little suction but wand still got suction even while vacuming floors is it suposed to stop suction from wand


My Dyson dc18 had the same symptoms. The wand worked well and the floor bar had no suction. After removing pieces & shoving my fingers into the machine (no blockage) I found the suction pipe rotates between two positions (floor and wand). It look ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Nothing happens on the "bare floor" setting, it does something on the carpet setting but definitely not the normal sound or suction.


The switch frequently go bad on those. p# h-59136035 ... Hoover S2220 Flair Bagless Upright Vacuum

My brush bar won't turn - works in bare floor mode, but carpet brush won't turn when it should...


Replace the belt the belt sounds like its worn or stretched the belts turn at high rpms and get very hot and soon just ware out they work fine on floors but when it comes to carpet they slow down, i hope this works out thanks ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC07 won't switch from bare floor to carpet mode. What should I do?


Hi its Darran at Dyson.Its worth moving the brush control dial from the bare floors position to the middle position a few times incase the dial has simply become stiff. If this does not resolve the issue, you may need an engin ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

My dyson is stuck on bare floor mode. It makes it very difficult to vacuum carpets. Can I fix?


... Dyson DC14 Bagless Upright Cyclonic Vacuum

Dc14 won't vac. Carpet, floors, wand works, bar rotates. TY


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hoover Savvy has limited suction when cleaning the floor and carpet


With the unit standing upright, double check the clear plastic air passages on the sides of the vacumn to see if they are clogged. ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Suction only works using the hand held mode, there is no suction when try to use on carpet mode,


There must be a clog in either the hose, dirt inland by the brush roll, or bad filters. If you have suction at the end of the hose, then look lower all the way to the brush roll. ... Vacuums

Dyson 23 Animal keeps putting itself in floor mode, when I press the button to change to carpet it turns itself back to floor mode


Make it impossible for it to turn back into flor mode ... Vacuums

Dyson animal D28 suction on floor vacuum mode is so strong I can't push the machine. Last used for hand tools, is there some mechanism that is stuck?


... Vacuums

S7000 my miele upright vaccum cleaner looses it suction when on carpet mode, suction is perfect when upright (hose). The suction lasts for appox 5 mins when on the carpet and it stops.


... Miele Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0800 seconds