Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

How do you replace the pre filter catch on a dc07 please

Answers :

The pre filter retaining clip is easy to fit, but hard to get the old one out. This is the easy way to do it:-
Turn the machine over, where the bottom of the clip should be is a plate blocking access, it is held in place by a torex headed screw. DO NOT remove this. Instead drill about an 8mm hole through the plastic plate, roughly in the middle level with the large 'A'. This will give you access to the bottom of the clip. Put a flat blade scewdriver through your new access hole and push out the broken clip. It should spring out with a couple of knocks with the palm of your hand. Turn the machine upright and push in the new clip. The hole is not seen and as long as it is a neat job, does not affect the strength of the plate.
Cheers Malc.
Or take the torx screws out and remove the vent that they hold (this is hard) you need to work it like crazy (taking the hepa filter out (under the dustbin) helps). then you can just use a hammer and flat head screwdriver. no drilling needed
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you replace the pre filter catch on a dc07 please

The pre filter retaining clip is easy to fit, but hard to get the old one out. This is the easy way to do it:-Turn the machine over, where the bottom of the clip should be is a plate blocking access, it is held in place by a torex headed screw. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The pre filter catch on my DC07 has snapped. I have the replacement, but can't get the bit left in the filter out! any ideas?

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 The plastic pre filter catch snapped on my Dyson. I have a replacement already, but can't figure out how to remove the bottom of the broken one. It looks easy enough to slide/snap the new one in but accessing the old one isn't easy. What do I need to do to get it out?

Turn your dyson over so you can get to the bottom undo the screw and then you can see the bottom of the clip a gentle tap with with a screw driver blade will knock it out and the other one slips in ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do you replace the steel pre filter catch? Mine broke and I ordered another, but how do you get the broken one out of unit in order to replace it with a new one?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I need instructions on how to replace filters in the dc07 please

You first need to purchase a filter. When you have it, stand in front of the machine.\015\012- Look at the right-hand side wheel. To the left of it there is a lever with ridges/ribs and a half-moon shaped top with a an arrow image on it. Push t ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 Filter Release Catch removal

If its the part im thinking of its a small spade like catch thats glued into a hole in the chassis normally id lay the machine on its front and gently tap the old catch out with a flat end screwdriver and a small hammer be carefull its very brittle ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson DC07 is screaming load. I have replaced the lifetime filter and the hepa filters. I also replaced the clutch and brush. I took the canister apart and cleaned it. It works, but is so loud something else must be wrong

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Will the broken pre-motor filter housing catch affect the overall suction of the vacuum?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I just bought this vacuum at a second hand store. My girlfriend told me to grab it as it such a quailty product. How ever I can't find a model number or anything else. I need a manual please. Does it take bags? Do I need to replace the filter or just wash the one I have? It is black and silver, cannister. It also says big gary's vacuum system warehouse in surry British Columbia, Canada. It also says to use filter pow-r-nozzle 96. I have no idea of the year.

I suggest you google what you know. I dont think anyone here can suggest where you can get a manual for a machine you dont even know the name of.\015\012\015\012You ask about a bag ... I dont know ... is there one in it now? You ask abo ... Vacuums

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!

... Miele Vacuums

Noisy vacuum I have a eureka capture that I bought in april it's making a horrible high pitched squeal type noise, I have made sure my roller is clean, my filters are clean, i replaced my hepa filter and there are not any blockages I don't know what else the problem might be. Could you please offer other suggestions to fix this?

... Vacuums

I have bought new filters for my hoover sensory 2300w . Which way do I replace the the pre motor filter? White side inwards or grey side inwards ?

... Hoover Vacuums

I have a Dyson DC07 Yellow Vac, I use this vacuum professionally and clean it after every job so there is no issues with the filter which are replaced regularly. When you turn it on it makes a noise as if it were blocked....I have checked all pipes, hoses and now disassembled the machine to the point where the motor is out. I have found that a small rubber valve or bleed valve (Attached to the right hand detachable filter housing and activated via an internal spring) is popping when the vac

Hi, Where exactly is this spring? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a shark transformer Vac EP602RF. I want to know how much the filters cost. My daughter threw the non-woen pre-filter away thinking I had replacement ones.

... Vacuums

Dyson DC07 Filter Release Catch removal

Yes sorry i know what mean you need to remove the motor casing to reduce the risk of breaking any parts. Lay dyson on the front and remove the bottom plate and roller bar. Now you need to remove the belt from the motor pin lay on left side look t the ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson DC07 animal ( purple). If you are standing behind the vacuum I am missing the lower righthand connection...therefore whatever is suctioned up comes out at that point just over the back wheel. I would like to purchase a replacement for this part. In the manual I believe this part is labeled as C. Can this part be purchased separately ?Please Help....

Hi there SmartAlec from NelsonVacuums.com.au i am not sure if you are based in australia but if you are you can ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Don't want an expert. I wan someone with authority that can make an intelligent decision regarding the way you sell replacement filters. It looks as though the patients are running the ward at HQ. This freak insane! Maniacal and just plain stupid! Tell me something Mr Expert, my closest choice was "vacuum expert" How is this expert going to know and fix the asinine way b&d devised a plan so that the consumer would enjoy wasting a better part of their day. Who, please tell me, who with a drop of

Ouch! So go into Lowes get a 10 pack of electrostatic register vent filters back in the furnace filter section. Take your old filter off and if it's a paper corrugated looking cone just wash it really good and dry it out...if it's disintegrating then ... Vacuums

Sabichi Model No WK 0801 10596 bagless vacuum cleaner - filter needs replacing where can I buy one from and what is the cost please.

... Vacuums

My dyson dc07 filter catch has snapped off and it's stuck

You need to take off the little vent that goes around the filter. this is hard. you take off the cover for the hepa filter (under the dustbin) there are three catches. you take off the two torx style screws under the vent and then you work the vent u ... Dyson DCO7 Upright Vacuum

I am losing suction and it sounds as if there is a leak in the vacuum(I hear air rushing around). There is also a high pitched noise. Dyson dc07. Can there be leaks in the gaskets where you clean hoses and filter? are they replaceable. Does the noise suggest the bearings are going in the motor?Is it worth getting fixed?

It wont be a gasket problem - they don't tend to fail. \015\012\015\012A high-pitched noise can be a number of different things. That is too vague to diagnose on here with the description you have given. Can you be more specific? ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I recently ( approx. 2-3 months ago ) purchased a dirt devil. Now it is not picking up properly. When I push vacuum forward it picks dirt up a little bit, when I pull it back all the dirt falls out of the bottom. I replaced the filter today and it has not solved my problem. I dont know where my warranty is. Can you please help me?

Hi sounds like your line is stopped up somewhere , check ur suction an make sure your brushes are spinning, if they are try a wire clothes hanger to the hose at the bottom hose to dislodge anything that mite be stuck ... Dirt Devil Vacuums

How do l change the filters please - Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi there SmartAlec from NelsonVacuums.com.au assuming your dyson is the one pictured it will have 2 filters. \015\012\015\0121st. If you look at the machine fro ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My hoover windtunnel is not picking anything up all of a sudden. Also the roller underneith is not spinning. I've replaced filters and the attachment part is working fine, just when it's in the upright position it won't pick anything up. It also doesn't seem to be self propelled anylonger either. It use to **** everything up, including the dog. Please help!

The belt that drives the brush roll has broken. That's why it doesn't pick up and why it doesn't pull itself forwards. Check the User Manual (download from Hoover website if necessary) for information on replacing the belt. Good luck! ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a hoover all terrain cleaning for carpets and hard floors and the Brushes will not rotate. I have replaced the filter on the bottom which is recommended by hoover and the brushes still wont rotate. Please advise

I assume this unit has no mechanism to turn the brush but instead using the air flow to activate the brush, in this instance it could be that there is dirt which is caught up in the brush which is stopping the rotation.A nice good clean and make sure ... Hoover Vacuums

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.

Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0809 seconds