Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?
Brush nopt turning - only picks up a bit of dust
\015 Brush not turning - only picks up a bit of dust . Motor sounds normal.\015
Did you check the belt if it is broken replace it that should do it
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Brush nopt turning - only picks up a bit of dust
Did you check the belt if it is broken replace it that should do it ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'
HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum
Roomba is not picking up dirt but does pick up dust. That is, the dust chamber has dust in it but the dirt chamber is empty. The brushes don't have any fluff on them either which is not normal. The fan is blowing out plenty of air, the filter has been cleaned but we suspect the brushes aren't turning. an you help?
... Roomba Vacuums
I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than
Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum
I want to brush the pile up on my carpet do I need a special attachment to do this??. I have shampood it and it still seems a bit flat. When I shampood no water/foam filled up in the front tray???I am sure I had attached everything correctly. The only thing I can think of is when I attach the brush and tray to the front of the machine, do I turn the handle back to the right way up, or do I leave it upside down, this is the one that picks up the belt.
Here's my online guide for using the Kirby shampooer....\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum
Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!
... Hoover Vacuums
Model mcv5237 brushes turn, bag expands, but not enough pull to even pick up dust or light dirt. this happened suddenly. went from working fine to this. HELP no clogged lines anywhere
Your accessory setting is open LOL its ok quick fix hahaha ... Panasonic Vacuums
For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.
... Kirby Ultimate G Bagged Upright Vacuum
In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.
... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum
Eureka 4D. Brush turns but not alot of suction. dust bunnies build up inside the hose at the bottom and at the dust brush connection. Seems to be very hot. ?????
Try cleaning the filters ... Eureka WhirlWind Litespeed 5844 Upright Vacuum
I have a roomba 435. I've had it for about 3 months, it had been working great until it started to sound a little different (louder). Now I noticed that it doesn't pick things up, it just pushes them around, I then discovered that the brushes aren't turning. I cleaned them out, no parts are missing. Brushes still won't turn. Help please.
Hmmmm....I know exactly what this is... Think back...the last time it was used when it worked...did it pick up something like a sock or get stuck somwhere?????? If you look on Ebay, it is polluted with this model Roomba. There is a gear that strips. ... iRobot Roomba 410 Robotic Vacuum
Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o
Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
When I was using my Bissell ProHeat 7901, I smelled something hot (almost burnt) and turned off the vaccum. When I turned it back on, everything seemed to be working, but the vaccum part was not making the same sound. The bristles are still turning, but it isn't picking up as much and is leaving quite a bit of lint on the carpet. Could the belts be worn? How do I tell? Thanks!
Ya that is probably the issue. Here is a link to the belts you need and to the manual which has instructions:Bissell ProHeat Belts and M ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag
... Euro-Pro EP621 Bagless Upright Vacuum
Burning smell. replaced belt and brushes are turning. still picking up.
... Hoover U5507900 Elite Rewind Bagless Upright Vacuum
ROCK SALT ON CARPET DOES NOT GET PICKED UP NOTHING IS BLOCKED, BRUSH IS TURNING, FILTER IS CLEAN, BUT IT STILL THROWS DEBRIS ALL OVER INSTEAD OF PICKING IT UP.
It could be that you need to replace the belt. Here is the belt you need:Dyson DC07 Belts and Manual ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i
At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum
IRobot stopped picking up larger bits from the carpet. It picks up the dust, but anything larger, it leaves behind. Have changed the filter/brushes. Is there anything else I need to do
Its sounds like the brushes aren't turning. Pull the vacuum and bin off the back and start it and look to see if the brushes are turning. ... iRobot Roomba 560 Robotic Vacuum
Hoover upright bagless vacum.motor runs, brush turns, no suction through hole behind brush roller. however there is suction going out of dust cannister filter flap to motor. what could possible problems be?
Sorry to read about your problem, I hope this helps you out.you have a clog between the brush and bagI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.
Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums
My Kenmore canister model (116) 26212601 works in hard-surface mode (basic suction), but the brush won't spin for carpets, and when I try to turn it on, it makes a whiny sound and then turns off as it does when I need to press the overload button. I looked inside a bit, and the belt isn't broken--it seems fine. So not sure what the problem is. Thanks for any help.
... Kenmore 27815 Bagged Canister Vacuum
Roomba goes in a circle moves about 5 inches and then turns in a circle again. It won't dock or go any farther than a few inches before turning in a circle again. The roomba has been cleaned inside and out. All hair and debri as been taken out of the wheels and brushes. i opened the case and cleared all the debri and i dusted the sensors in the front. Not sure what to do now.
... iRobot Roomba 550 Vacuum
The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.
Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
The belt broke and after putting on new belt I dicscovered the cylinder with the brushes attached wasn't turning. After I finally got the cylinder to turn it makes a very very loud noise and also now it doesn't pick up the dirt. The vacuum is less than a year old.
Check the cylinder with brushes does not have hair or carpet fibers causing it to bind. With the belt removed the brush should turn freely and fairly easy. The original belt probably broke because of this. You may have to fully dis-assemble the head ... Dirt Devil Vacuums
The spinning brushes on the vaccum no longer spin, how can i fix this? The vaccum picked up a very small wire from a video game and i turned it off immediately. I unwound the wire but the brushes no longer spin.
You have either broken the belt or more likely the clutch easiest is to replace cleaner head assembly \302\24375ish or call Dyson and arrange a service if you're not DIY inclined but check belt !st ... Dyson Ball DC24 Bagless Upright Vacuum