Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?


Answers :

Hi its Darran at Dyson.

The trigger mechanism which stops the bin base coming open is part of the cyclone top. this part can be purchased via our website at www.dyson.com.

Kind regards
Dyson Customer Service
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :


Hi its Darran at Dyson. The trigger mechanism which stops the bin base coming open is part of the cyclone top. this part can be purchased via our website at www.dyson.com.Kind regardsDarran Dyson Customer Service ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Our Bissell Cleanview II 3576M does a great job except that the filter cup below the dirt cup gets full very fast and the dirt cup barely has anything in it. To clean the whole house, I have to empty the dirt cup and clean the filter several times. It didn't use to work this way. It seems like something is missing, a gasket or seal maybe? I don't think dirt, hair and debris should be going straight to the lower cup and bypassing the upper. I looked at the user guide but can't see why it's happen

Contact Bissell Direct for a parts diagram and support at \015\012\015\012http://uk.bissell.com/EmailUs.aspx\015\012 ... Bissell 3576 CleanView II Bagless Upright Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

It seems to be blowing dirt around not suking but when removing the attachment to clean stairs etc the pipe works fine have washed filteR ? SLIM UPRIGHT DC ALLERGY 18. Have cleaned out filter emptied cylinder taken any bits of cotton or hairs from brushes..........

... Dyson DC07 Bagless Upright Cyclonic Vacuum

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug

Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The handle release lever (Part N. 38434-021) on my Hoover WindTunnel upright vacuum (uses Y bags) broke. How do I install the replacement release lever (pedal) that I purchased?

You can buy Hoover Handle Release Lever 38434-021 at \015\012http://partsreadyonline.com/item.php?ItemID=798 ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Bissell Steam Cleaner that is not sucking up the water when cleaning. I used a full container of water and when it was empty I emptied out the water, only to find very little dirty water in it. I noticed the window, as i used it, seemed like it wasnt sucking up the water. I took the plastic cover off to clean it (it didnt look very dirty in the first place), an i noticed that the grey plastic flap was on but not moving up or down. I thought there may be dirt in it that prevented it from

... Bissell Vacuums

My FIL purchased an Electrolux bagless canister vacuum model EL5 76501 last year. When I tried to use it today, the hose keeps pulling out of the power brush whenever I pull it towards me. it doesn't seem like anything has broken off. The only thing I noticed was that the rubber ring washer seems to be flattened. Could it be something that simple or do you think some part has fallen off and gone missing? Regards, Craig Somersett

I believe I've just had the same problem and after searching for a small gray horsehoe clip that needs to first be found and then inserted into the slot for it on the tube section that comes out of the beater bar. Insert this clip from the outside af ... Electrolux Vacuums

Cannot open bonnet on fiat punto pulled the lever it popped up went to lift bonnet but cannot open it as it seems to be still locked lift the lever but does not release it

... Kirby Shampooer Shampoo Hose G3 Ultimate Diamond Vacuum

My Bissell bagless vacuum does not seem to work anymore. It will start to with a suction and then instead of picking up the dirt, it appears to blow the dirt out almost in a cloud of dust and debris from the front.

This is caused by a dirty air filter and/or a blocked vacume hose ( most of the time the blockage is at the bend where the hose enters the floor sweeper area ) ---\015\012remove and tap out and brush the filter ( or use a air compressor to blow ... Bissell 6595 Lift Off Bagless Upright Vacuum

I am replacing a foot pedal on an upright Sharp vacuum cleaner-EC-TU2607. I have the broken foot pedal removed from vacuum cleaner proper but it is the removal of the broken pedal from its spring load that has me puzzled. I applied some pulling effort on the pin that holds the spring in place but there doesn't seem to be any give. Is that the correct approach or is there something else that one should be doing first to release some of the resistance by the pin or spring? Thanks!

... Sharp Twin Energy EC-TU2607 Vacuum

My 88 year old mother bought a Dirt Devel DHC001 - has been used twice but it looks blocked and has no suction but there is suction at the pipe end if I take it off. I have opened the red end and emptied out but there seems to be dust in the rear part and I have no idea how to get it out. The shop she bought it off thought they were being helpful and removed all packaging but seem to have taken instructions as well.

To answer this properly, I am going to need the actual model number on the bottom of the unit on the silver/metallic sticker. Usually MO###### If you can get that I can help you out further. \012Mark ... Vacuums

I have a clearviewII model 3576-3 and the handle release lever is broken. How to I remove the old lever and install a new one? Thanks, Pat

... Bissell Vacuums

On-off switch My problem is finding a source for an on-off switch for an electrolux vacuum sweeper model 2100. I have replaced the broken toggle and now the sweeper turns on but only as long as the outside button is depressed. It appears that the on-off switch itself is broken as the switch does not ''hold'' when the toggle is activated. It seems to return to it's ''off'' setting as soon as the toggle is released. What ''holds'' the switch in its ''on'' position? Does it depend only on the on-

Hi Hugh. The 2100 has a rocker switch under neath the button. it is probably broken, or the button has a worn detent spring. If you would like, I could send you a switch kit with the rocker, button, and detent spring enclosed for around 20 dollars ... Vacuums

My old bissell 3510 upright vacuum seems to have no suction into the bag...I replaced a broken belt several days ago, and now the vacuum picks up debris, but seems to just collect it behind a wheel..The bag does not "puff out" like it used to...How can I fix this??

... Bissell 3510 PowerPartner Upright Vacuum

Hoover WindTunnel Self Propelled Handle Release Lever broken

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Kenmore 31913 Foot pedal release lever broken-need to replace

FixYa techs - thank you for your response but I solved the problems. It took me 2 hours of continual searching but I finally found the parts - listed under the tab sew machines of all things!? There is one pedal in stock and I called t ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Handle release lever is broken

... Hoover Tempo Widepath Upright Vacuum - Blue

Seems to be picking up dirt but not very well & there is nothing in the canister to empty.

More that likely the top filter is clogged. step one. remove the clear plastic dirt holder. step two. reach inside the upper dlear jug, still attached to the unit and twist the large disc you see counter clockwise about a 1/4 turn. pull it down a ... Bissell 6594 PowerForce Bagless Upright Vacuum

Hoover savvy handle release pedal does not retract. There does not seem to be any mechanism to force it back, is something broken or missing, like a spring?

Yes the handle release pedal is broken. i have the same problem and ordering the spare as i'm writing this email ... Vacuums

Su2914: loss of suction even when cylinder is empty!! doesnt work correctly when pet attachment is added either, only seemed to work ok for first 4 months then loss of suction, will pick up eventually but quite poorly! Should I take it for a service? Thanks

... Samsung Vacuums

How do i reattach the bottom of the dirt canister I had released to empty the canister and the hinge came loose

... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have a Dirt Devil Swivel Glide Vac with a broken belt. I have purchased the correct belt(#4).The bottom is off and I cannot tell where the belt connects to. Please help. Jann

It connects to the left side with the little metal rod sticking out.then connect to the wooden roller. in the space without the brush on it. roll the wooden piece to check if everything moves. then put back together. ... Dirt Devil Vacuums

I can't seem to empty my Dirt Devil Kurv - Vacuums

If it is the same as mine you have to remove the dust filter and then remove or empty the bin. Hope this helps. ... Vacuums

Every time I try to vacuum my apartment with my Dirt Devil Featherlite bagless vacuum, it shuts off before I have finished one or two rooms. I then have to wait 30 minutes before continuing. I had the vacuum for 2 months before exchanging it and it is doing the same thing with my new one. It seems to happen after the first time I empty the cannister. Any ideas?

Your motor in the vacum is getting hot.Thats why it shuts off.Its fitted with a shut off switch to stop you doing any damage to it.1 The reason for getting to hot is that you are filling the cannister to full.Try emptying it half.good luck. ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0652 seconds