Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Brush bar is scratching hardwood floors. It seems too low!

\015 Dyson, Animal. Purchased about 3 years ago.\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brush bar is scratching hardwood floors. It seems too low!


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.


The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson dc14 brush bar is not turning at all. Everything else seems to be fine. I just replaced the brush bar but still no movement. What else could it be?


Hi there,I'm sorry to hear you're having difficulty with your DC14 Animal. If the brushbar doesn't rotate, please check you have the brush control set to 'Carpets', not 'Hard floors'. The brushbar will not rotate when the machine is standing ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Low suction The beater bar still spins fine, but the suction seems low. I have cleaned all of the filters, but it is still too low to spin a lot of the attachments.


Hi Megan,I'm sorry to hear you're having difficulties with your DC17. If it doesn't seem to be picking up as well as usual, you may have a blockage somewhere in the machine. To check for this, please follow the steps shown in our online suppo ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please


... Vacuums

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

My Dyson DC25 (which I've had for about a year and a half), doesn't seem to be picking up like it used to. There doesn't seem to be a problem with the brush bar, but I can't figure out what the problem is or how to fix it


Hi there,\015\012\015\012Sorry to hear you're having a problem with your DC25. You should be able to resolve this issue by following these simple steps: ... Dyson DC25 All Floors Bagless Upright Vacuum

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

Brush bar not spinning when set to high or low on carpet


1) adjust the belt, see for broken or worn, and replace2)see for brushroller obstruction, and clean it and repair3) see if the brushroller without belt run smooth, otherwise repair and fix it.Lubricate.4)See if the motor run without load( ... Vacuums

I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?


THE IMPELLER LOOKS SHOT.. 25 QUID FOR NEW ONE,,LIFT THE LID AND TURN THE ROUND PIN AND CHECK FOR RIDGES ROUND THE WHITE IMPELLER,,IF NONE THERE THATS IT,, HAPPEND TO ME TEN MINS TO FIX GEORGE ... Kirby Ultimate G Bagged Upright Vacuum

Beater bar brush won't turn and seems to be seized up.


I removed the pump and sprayed silicone spray on it. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Belts on my vacuum last only a short time, the keep getting chewed up. Seems that the belt does not align properly between the brush bar and the motor shaft.


The belt is either contacting the \015\0121. Check to see that the roller is installed properly (make sure it is not reversed and that it is all the way in).\015\0122. Check to see if there is any play in the motor shaft and that the mo ... Eureka Smartvac 4870 Bagged Upright Vacuum

The spot bot brushes do not seem to be working correctly. It is a low ply carpet.


Hello program the SpotBot controls based on the type of spill or stain. Set the "surface stain cycle" for recent spills that have not soaked into the carpet, and the "set-in stain cycle" for older stains. Failure to set the correct option ... Bissell SpotBot Robotic Wet/Dry Vacuum

We have a Tornado CV30/1 and the brush bar is not moving. Belt seems to be intact. Suggestions?


... Tornado Vacuums

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?


The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

Roomba seems to bounce up and down as it goes across the carpet. works fine on hardwood. have cleaned the brushes numerous times..


I had the same issue and I fixed it by removing the left yellow clip on the main brush. The clip seems to have been rubbing on the inside wall. I hope this works for you too!! ... iRobot Roomba 550 Vacuum

Just got my dc33... one issue... the dial switch to control btn bare floor / carpet mode doesn't seem holding in it's position when I set to the bare floor mode... it keeps coming back to carpet mode with brush-bar activated... the dial doesn't really click to the floor mode. Any advice on this?


Hi there,I'm sorry to hear you're having difficulties with your DC33. If you're concerned that the brush control doesn't seem to be staying in position, it's probably best if you get in touch with us directly. One of our experts will be h ... Dyson DC33 Bagged Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

The brush bar on my Dyson DC17 stopped turning.


If this model has a brush control - i.e a roller at the side of the model which controls brush to spin or not, then its a protected brush model - therefore even if the drive belt is intact the Dyson would have to be repaired by a service personnel or ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

I have a bissell powerforce bagless turbo. The problem is the brush bar is not spinning. I have cleaned out all the debris on the brush itself, and taken it apart to make sure nothing is blocking the


Sorry to hear you're having difficulty with your vacuum. You may want to have a Qualified Technician at a BISSELL Authorized Service Center inspect your vacuum. Here's a quick link to locating a Service Center. ... Bissell Vacuums

Dyson Animal DC 28 brush bar removal


Hi there, it's Jack at Dyson.I'm sorry to hear you're having difficulty with your DC28's brush bar. I've attached our video which shows the correct way to remove any obstructions and reset the machine, in case this is useful to you.Th ... Dyson DC28 Animal Bagless Upright Vacuum

Vax Mach 7 - the brush bar won't rotate but the belts are fine


... Vacuums

Is it possible to remove the brush bar from the housing of a mieleTurbobrush STB 205? The brush bar is not spinning due to been dirty and clogged and needs to be removed for cleaning. Is it possible to remove the brush bar????


... Miele 06271980 STB 205-3 Turbobrush
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0634 seconds