Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Need to reclace power cord

\015 How do I replace the power cord on the DC07 Dyson vacuum\015

Answers :

Greetings,
\015\012
\015\012I have gone ahead and taken pictures of how to change the cord on a Dyson DC07 upright. Here's what you'll need to have handy in order to complete this repair:
\015\012
\015\012- T15 Torx Bit Screw Driver
\015\012- Dyson DC07 Power Cord For All DC07 Models, Part 905449.
\015\012- A 2mm or Smaller Flat Head Screwdriver (width of the tip)
\015\012- Needle Nose Plyers
\015\012- Patience (haha)
\015\012
\015\012The cord above is actually a link back to our site if you have yet to purchase your cord. We carry most every Dyson part.
\015\012
\015\012IMPORTANT: MAKE SURE YOUR VACUUM CLEANER IS UNPLUGGED BEFORE DOING ANYTHING ELSE!
\015\012
\015\012Step 1. First thing you'll want to do is to unwrap the cord from the machine, and remove the handle from the upright part, then slide the hose all the way down the wand, and remove the hose from the handle assembly completely and set it aside. Also remove the dust bin assembly completely from the machine as well.
\015\012
\015\012
\015\01286bdf5c.jpg\015\012
\015\012Step 2. Once you've remove the handle from the machine I find it easier to work on if you lay vacuum on it's back, with the switch button facing upwards. Now remove the T15 Torx bit screw that is directly below the switch actuator. I have circled the location of this screw in the picture below:
\015\012
\015\012
\015\012080ce87.jpg\015\012
\015\012Step 3: After you have taken off the screw, you're doing to need to remove the switch box housing from the vacuum that the screw was securing. Simply use your flat head screw driver, and pry the two small arms upwards. Be careful when prying, the plastic components on Dyson vacuums are really cheap quality plastic, and I can't tell you how many times I have seen these plastic parts break. Here's a picture of the location of where you should pry the switching off:
\015\012
\015\012
\015\012357199b.jpg\015\012
\015\012Here's what the vacuum should look like after the switch housing has been removed:
\015\012
\015\012
\015\012eb76162.jpg\015\012
\015\012Step 4. Use your needle nose plyers to remove the terminals from both of the switch poles. Also be careful when removing these terminals, don't force it or it will break the pole right off of the switch, and you'll then have to replace the switch along with the cord. Also you'll need to remove the two white wires that are connected together apart, also using your needle nose plyers.
\015\012
\015\012
\015\0120ebca47.jpg\015\012
\015\012Step 5. After you've removed the two terminals connected to the switch, as well as the two white wires that were connected, follow the electrical cord up until the point that it enters the vacuum cleaner to the rubber cord protector. Lift straight up on this cord protecter to remove it from the vacuum.
\015\012
\015\012
\015\01290104f6.jpg\015\012
\015\012Step 6. You'll have to now slide the cord out through the cord protector so that you may install the protector on your new cord. Unfortunately as you'll see, your new cord does not come with the plastic terminal protectors that are on the end of the wires, so you'll need to take off these plastic ends on both the black, and the white wires that come from the cord. The other wire that you see in there that has a white wire with no plastic cover, and a black wire that does have the plastic terminal. There's no need to remove the plastic terminal from the wire that runs down into your motor, just leave these alone. If you look closely at these plastic terminal covers, you'll see that one side of them have two little ridges on the inside, also that the bottom is flat, and the top rises upwards on one end. To remove these plastic parts, use your 2mm flat head screwdriver and insert it through the top part that has the two ridges on the indside. While your screw driver is in as far as it will go, lift upwards away from the wire while pulling out the wire at the same time. Repeat this on the other wire as well.
\015\012
\015\012
\015\0125d505de.jpg\015\012
\015\012This is how the wires look like without the terminals:
\015\012
\015\012
\015\012d0ba44f.jpg\015\012
\015\012Step 7. After remove the plastic terminal covers from the wires, pull the cord through the rubber cord protector and remove your old cord. Open your new cord, and now you'll have to feed the two wires through the cord protector. Simply push the cord through the ribbed end of the cord protector. You normally can push the cord hard enough so that the ends of the wires will come out the other end fairly easy. If the wires don't come out, use your needle nose plyers to pull the metal ends of the wires through the rubber cord protector.
\015\012
\015\012Step 8. Reconnect the wires to the switch, as well as connecting the two white wires together. Here's how the wiring should look like when done properly:
\015\012
\015\012
\015\0122a63631.jpg\015\012
\015\012Step 9. After reconnecting the wires to the switch, and to the other white wire, you'll need to put the switch back in place, along with the cords, and the cord proector. You can see little channels that the cords actually sit in to keep them from pulling out. Place both the wire on the bottom that goes to the motor, as well as the electrical cord into these channels. The two white wires that are connected together go to the left of the switch. Here's how it should look like when you're finished:
\015\012
\015\012
\015\012df00511.jpg\015\012
\015\012
\015\012Simply put the switch housing cover back over the switch and cords, and screw the Torx bit back in, and then test the vacuum to make sure that the cord works.
\015\012
\015\012I hope that this repair was helpful to you with fixing the cord on your Dyson DC07. If you have any questions about this repair, or need further help on replacing the cord, please use the Clarification Request, or leave a comment on this repair and I'll be more then happy to help you further. If this was helpful to you, please be sure to rate the review helpful by clicking the thumbs up incon in the top right hand corner. Again, if you ever need any supplies for your Dyson, we do carry most parts and accessories on our site under our Dyson Parts Section .
\015\012
\015\012Thank you,
\015\012
\015\012Chris J.
\015\012GoVacuum
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need to reclace power cord


Greetings,\015\012\015\012I have gone ahead and taken pictures of how to change the cord on a Dyson DC07 upright. Here's what you'll need to have handy in order to complete this repair:\015\012\015\012- T15 Torx ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I need a new power cord for the power nozzle on my Electrolux 2100 canister vacuum. The power nozzle has part number N115M written on the bottom. I have found the power cord for power nozzles PN6 and PN7 online, and it looks identical in photos but I'm not sure if it's the right part.


You can buy the hose at an authorized Aerus Electrolux store. If near enough, they will deliver, if too far, they can ship it. The nearest dealer can be found using the below link. Just follow the instructions.\015\012Just provide the model ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

My dog chewed through the power cord on my Dyson DC15. I have purchased a new power cord and need instructions on how to remove the old one and replace it with the new one.


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a Hoover Wind-tunnel Vaccum (Model U5433-900) that needs a new power cord. I am looking for step by step directions for replacing the power cord


... Hoover Vacuums

Need to replace power cord on Hoover windtunnel need wiring help


Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to ... Hoover U5399-900 WindTunnel Lite Upright Vacuum

The iron needs a new power cord; however, the screw at the back of the iron seems to need a hollow star driver. What tool do I need?


You've identified it in your question. These screws are just one type of so-called "security" screws (there are many others) that are designed to be turned only with a driver that matches the head. You can often get these screws to turn with a small ... Vacuums

The power cord on a flat iron broke/got chewed through and needs to be replaced. how can I open it to get at the cord or fix the cord?


... Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

Need to replace power cord on Hoover vacuum.


Remove the dirt container and look for screws. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Need to replace the power cord


Pry out the clear plastic covering the Fins going around the body\015\012Surprise no fins in there but there are some screws ... Rainbow E series Canister Wet/Dry Vacuum

Damage power cord needs to be replaced on Bissell 3920


... Bissell 3920 Bagless Upright Vacuum

While replacing my power cord on my DC25 a spring popped out I have no idea where it goes. I need a diagram so I can see where it goes


Here is how the switch assembly should go together: ... Dyson DC25 All Floors Bagless Upright Vacuum

I need to replace power supply. where the cord


Greetings from GoVacuum.com,Unfortunately there is no fuse on a Kirby Generation model. In my 10 years of repairing Kirby's as well as other vacuums I will tell you that 9 times out of 10, when a Kirby Generation doesn't turn on, it's the ... Kirby Generation 3 Bagged Upright Vacuum

Power cord has been split accidentally - needs to be adjoined to new plug


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a electrolux 7000 my cord brok off and it got succked in. igot it apart. I DONY KNOW HOW TO PUT THE COIL SPRING ON THE POWER CORD WHEEL. NEED HELP


This is very difficult to reassemble correctly, and more difficult to explain properly. You need to take the vacuum to the nearest authorized Aerus Electrolux store for reassembly. Or call for free pick up and delivery.\015\012\015\012 ... Electrolux Lux 7000 Bagged Canister Vacuum

My kenmore progressive caniser needs a new power cord. the plug had one of the metal prongs break on the plug. how can I replace the cord? model 22812201


I do not know if you want to replace the replace the power\012cord or the receptacle for the power wand?\012\012If you need the prong for the power cord you can purchase a\012replacement power plug from a local hardware store and it will functi ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I need a complete parts manual for a GE #106766 canister vacuum cleaner sold at Walmart. I need the plug receptor in the cannister for the power nozzle cord


... GE 106766 Bagged Canister Vacuum

Need parts diagram for euro-Pro ep601. I need to replace the power cord, but cannot get the motor gasket guard off.


Hi!You need to release a "clip" under the handle(this is on top of the dust cup) and then look for a hidden screw right under the thermostat label. ... Vacuums

I need to replace the power cord. what tools do i need


The Kirby vacs have a 50year warranty. You sould contact the person you baught it from and have them replace it or if they gave you one (no labor is coverd on the warranty) then you will definately need a Philips screw driver and a tub to hold all th ... Kirby Ultimate G Bagged Upright Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.


... Sanyo Vacuums

I dont have a power cord and or foot pedal and need to know what I need.


Power cords can be found at http://search.totalvac.com/search?keywords=power+cord ... Vacuums

Need to replace power cord for bissell model 6585


A BISSELL Authorized Service Center should be able to help you out. You can find one nearest to you and call them first if you want: \015\012http://www.bissell.com/service-centers/?zip=Enter%20your%20zip%20code&distance=50&cid=ccsocial ... Bissell Vacuums

Need to replace power cord


Here are the Sears links to purchase both the part and the manual.\015\012\015\012http://www.searspartsdirect.com/partsdirect/searchByPartDescAction!searchByPartDescription.pd?brandId=0582&productCategoryId=0645000&modelNumber=116339223 ... Kenmore 22612 Bagged Canister Vacuum

Need to replace power cord and can't find how to open canister to replace


I had the same problem and could not find the other screws. You need to pry off the power cord retraction button, you will find two more screws under there. It's pretty easy after that!!!! ... Kenmore 22612 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0696 seconds