Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

The power head for doing rugs has stopped turning.

\015 I made sure that there was nothing clogging it - removed animal hair.\015\012\015\012HElp!\015\012\015\012Thanks,\015\012C in RI\015

Answers :

A clog usually only affects the vacuum action. If the brush is not turning, make sure the motor driving it still runs. Remove the bottom plate and take out the brush assembly--check the end bearings for being bound-up with debris and the brush surface clear of debris. Clean the bearings with a Q-tip, then lightly oil them inside with 3-1 oil or similar light oil. Make sure the brush turns freely when returned to it's place. If ok, install the drive belt paying attention to any necessary twists. Replace the bottom plate and test. If the driving motor doesn't work, try turning the shaft by hand. If bound-up and it isn't caused by wound debris, the motor probably needs to be replaced. Hope this helps!
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

The power head for doing rugs has stopped turning.


A clog usually only affects the vacuum action. If the brush is not turning, make sure the motor driving it still runs. Remove the bottom plate and take out the brush assembly--check the end bearings for being bound-up with debris and the brush surfac ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on


... Miele Blue Moon Bagged Canister Vacuum

When the power head is turned on it goes from green light to red light and stops. The belt is fine and there is no obstructions in the brush to stop it from turning.


This will happen only when the brush or motor does not turn the right speed \015\012make sure to pull the end caps off the brush and clean any hairs or fibers from it\015\012the motor you can try and turn it by hand with out the belt on a ... Fantom Vacums Lighting Canister Vacuum

Power head is dragging slowing down like the brush is stopping turning and coming back


Have you tried changing he belt ?. Some time the belts stretch out and they don't turn the brushes ... Filter Queen Majestic Canister Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Shark navigator power head will not turn on unless main handle is lowered to the floor


... Dyson Vacuums

I bought a new power head for my older Rainbow. The power head had a red button to push to engage the drive motor if it stops. Well, it stops often except if I'm using the tallest setting for carp


... Rainbow Vacuums

The Delta power head is not working. Brush is not turning.


... Electrolux EL6989A Bagged Canister Vacuum

Our Electrolux canister vacuum just stopped working when we were vacuuming the floor. The power does come on when the power head is attached but as soon as the power head is removed the power shuts off. I tried pressing the reset button but that doesn't help. Is there a solution that I can try at home?


Sound like you problem is in the connection going to the power head you will see a small screw on the power nozzel where it joins to the handle take out the screw and take it a part you will see where one of the bars have been disconnect from the pow ... Electrolux Guardian Bagged Canister Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

I have a tank style vacuum. When I vacuum with the power head it dims and slows down when I push the power head back and forth, but it powers back up louder when I stop pushing it If i remove the powerhead from the hose the vacuum works fine.


Most likely the belt. Thats the cheapest so try it first ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My Discovery 4210 Roomba will run normally for about 20 minutes on a smooth, wooden floor. It then begins the following sequence: run forward a few inches, turn in a tight counter-clockwise circle a few revolutions, stop, power off a few seconds, power up, repeat cycle from forward run. The sequence can be repeated seemingly endlessly if I don't turn off the power manually. I've replaced the motor, and led revolution sensor system on the left drive wheel. I've blown the dust out of everywhere. A


This robot vacuum has a electronic micro processor that controls the unit and tells it how to operate and where to go based on programmed parameters. It's quite a technical marvel. I have dropped a link here for contacting the company tech support li ... iRobot Roomba 560 Robotic Vacuum

Stops Immediately. We have a Beam Serenity model 2100 installed in the home and when the hose is inserted into the wall it turns on for a few seconds and then shuts off on it's own. Turning the handle's power switch off/on restarts the unit only to have it once again stop after a few more seconds. The canaster is clean. What could be causing this stopping issue? Thanks.


The Relay Control Board in the 2100 is bad. Replace and it should work just fine. ... Beam Industries 2900 Serenity Plus Central System Vacuum

Power Head keeps cutting in and out while vacuuming???Canister motor keeps running but the power head starts and stops like there is a short or some loss of connection somewhere. Any ideas?


My kenmore progressive vacuum had the same problem. The electrical terminal at the bottom of the wand was corroded. I used a flat head screw driver to scrape the female portion of the connector as best as I could. I then took off the plastic cover on ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

For some reason, our shark steam mop stop working. Usually after I plug the steam mop, the power light would light up then you would hear & see steam coming out of the mop's head but all of a sudden no power light would go on and no steam would come out. I can still use the mop, cause water from the tank still is able to flow down to the head. It's just that I'd have to use it like an ordinary mop not as the steam mop I liked. Pls help!!!


... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I was vacuuming under my dresser using the large power head and I bumped the power head against the dresser and it stopped working.


If it doesn't work after depressing the reset button, a wire in the power nozzle may have been knocked loose. If that's the case, it will need to be taken to an authorized Aerus Electrolux store for repair. ... Electrolux Guardian Bagged Canister Vacuum

We purchased a Shark Power Pet vacuum last month. We can't find the book and now the bar doesn't turn in the power head. We tried to order a manual but the model number keeps turning up as non existant


The model number is EP722 and the technical support number is 1-800-798-7398 Mon-Fri. 8:30 am to 5:00 pm EST ... Euro-Pro S3325 Handheld Steam Vacuum

Power head turns on and works the power that turns vacum on not


If the suction motor doesn't come on but the brush motor does, you have a bad vac motor. If neither motor runs, it's probably a cord problem. Most parts for these are not available anymore. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

My bissell power trak just stopped working i turned it off and a few hours later i turned it on again and it will not work. I switched over to an outlet i know works and it still didn't work I checked the outlet after and there's still power there. Is there an internal fuse?


... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

Our dyson absolute turbo head has stopped turning. I caught the edge of the mat in the head, I turned it off straight away. It won't go around.


It might have broken the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need:DC07 Belt Changing Instructions ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Power head has power but motor won't run


Circuit brealer switch may be bad, but the fact that Rainbow nozzle made this strange sound makes me think that it may have ha ... Rainbow E series Canister Wet/Dry Vacuum

For some reason, our shark steam mop stop working. Usually after I plug the steam mop, the power light would light up then you would hear & see steam coming out of the mop's head but all of


HEATING ELEMENTS BURNT OUT. WILL COST OVER $100. TOFIX. SHARK NOW HAS A NEW MODEL "SHARK 3" MUCH BETTER ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Power head stops and starts


The problem is with the connection between the flexible hose and the handle - there is a joint between the two that allows the flexible hose to rotate in the handle and the electrical connection here is not great!\015\012\015\012If the he ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I have a Beam serenity plus SP800A vacuum, the red light went on and the bristles stopped turning when I vacuumed up my bathroom rug. what does the reset button look like. Or does this model have a reset button. how do I turn off the red light so that the bristles start turning again?


... Beam Industries 2775 Serenity Plus Central System Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0650 seconds