Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy


Answers :

The following site has some great info on your machine:\015\012
\015\012www.dysonmedic.com
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy


The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Kenmore quick clean model 116.36724500 and the belt popped off so we took the bottom off and put the belt back on, but now cannot get the bottom floor plate back on! Please help! :( I have no


... Vacuums

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!


Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Hoover self-propelled windtunnel U6430-900 flat belt gets hot & becomes hard to push. It has a filter bag. Purchased 8/2/01. Took one plate off bottom. Used a compressor to blow out dirt & dust. Put new thin belt on.


Belts get hot when fibers from carpet get wound arounf the belts mounting shaft. Best to take a razor and cut off any fibers so the belt doesn't get hot again ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.


Model no. req ... Hoover Vacuums

Change belt How do I change the belt. I took the bottom off and removed the roller but can't get the rest apart to get to the place to hook the belt on the the drive.


... Hoover U4270-930 Vacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

Floor Attachment I took off my floor attachment, but now the belt seems to be off and I can't seem to get it back on right. I can't use the attachment and I don't know why it's so hard to figure this out. They say, just turn it to belt off, but when i turn it it lift's it up and can't line up with the belt off label. Then, when I turn it the other way, it's off. So I've been trying to pull it off so when it lines up with belt off, it's off. But the I turn it the other way and it's still off a


Try this,\015\012\015\012With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on t ... Kirby Generation 3 Bagged Upright Vacuum

Hoover F6025900 Steam Vac Widepath LS, I own this steam vac and I found bits of rubber under the machine when I turned it on, smelled like burned rubber from a belt? Can you please tell me if there is a belt on this carpet cleaner and if so, how to access the belt? I have taken out some screws and still cant get to the belt? Thanks


Well there is no belt, and not sure what the rubber would be from, everything is plastic or metal. Unless it is really an electrical smell, which means the motor is going bad.\015\012\015\012 ... Hoover Vacuums

Belt How do you remove the bottom plate to replace the belt. I have the brush off but can't figure out how to get to the other end to loop the belt


You need to take the top cover off to get to motor shaft. Some had a couple of screws from the bottom, others had tabs, use a flat blade screwdriver to fit into the slots at the bottom edge of the top, pry out and up to pop the cover off. ... Hoover Commercial C1403 Bagged Upright Vacuum

My belt broke on my kirby upright, I took the roller off and put the new belt on, but I cant get the hook to hook on the belt.


On the front of the nozzle is a big knob that you turn to load the belt. Take the nozzle of of the vac, turn the knob to catch the belt, keep turning it until it stops. You will know if the it caught the belt, it will be hard to turn. Put the nozz ... Vacuums

Dyson i got a free dc07 animal but the brush doesnt turn it appears the belt is still on it but i cant see how to get at the belt


Hi.\015\012\015\012There are 2 belts the one is hidden under the Black casing.\015\012\015\012If you require help got to this site http://dysonmanu ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

How do I clean out the suction side of a Hoover steam-vac Model#f6020-900. I took all the screws out and still cant get it apart.I vacuum before using it, but it still seems to find more hair.


These don't come apart. Hoover makes a thin long tool that will allow you to stick up into this suction side to clean it or use a long piece of galvanized metal strip to slide up into it and clear away the hair. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Cant get the bottom plate back onto my dyson upright DCO7i


You need to press hard and turn till they lock inhttp://www.youtube.com/watch?v=fN8k--LbuCs ... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

HOW DO YOU CHANGE BELT CANT SEEM TO REMOVE BOTTOM TO GET TO IT KENMORE WISPERTONE 116


The top cover to the light lense pops off at the ends. When you get that cover off then you will see 2 screws that are by the swivel neck. Take those out and then the whole body top cover comes off. That will get you into the roller brush and belt ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

The self propell does not work... i turned it over and took off th bottom plate and can see where the cable is suppose to be attached to the drive system, but it is no longer atteached, so it came out or a piece of the vaccum broke as it seems to be alot of plastic.. i see a screw and the end of the cable is still there... But where does it attach and how do i do it.. i havent taken the complete houseing apart yet as i have never done that before and wasnt sure about all the scres and what not..


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I took the hose off to wash it then after letting it dry overnight I put it back on but Im guessing it there was still a little bit of water in between the grooves which ran to bottom of vacuum and now my dyson gets stuck, sort of like a tight hinge. It vacuums fine but I have to keep pushing it down to the carpet with my foot. How can I fix this problem?


Lubrication at the pivot points ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do you remove the bottom plate to get a the belt for the roller


Have a look at the top cover you shuold have some screws in it remove them and lift off the cover to get to the bottom brushes ... Hoover Encore Supreme Energy U4293-930 Vacuum

Hello, I have a Riccar 8000. The belt works, the bar spins, and it will **** things up. However, it will not pick up threads and dog hair or anything from the carpeting. Mu husband took the bottom off and there were a couple of small parts on the plate. We have no idea where they belong. Could not see them in the photos in the manual. Could it possibly need a new roller? Any help would be most welcome. Thank you! Mary Simon


... Riccar Vacuums

Kirby g4 i cant get the belt back on try and still wont work ? can u help me


First things first...take the powerhead off of the front of the kirby. If you look at where the powerhead connects to the front of the kirby and you'll see a large hook...turn the hook using the crank on the front of the powerhead so that the belt is ... Vacuums

Replacing belt on kenmore quick clean 30012 & cant get plate off


... Kenmore Quick Clean 30012 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0750 seconds