Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

We are having suction problems. ran over a chord and there is now no suction when we turn it on. last time we brought it in, they said something about a gasket??


Answers :

Hi,

\015\012 There could be various reasons why this could happen.
I will tell \015\012you the reason's that could cause this problem and its solution.

1)\015\012 Internal hose has twisted small corrugated tube
Twist\015\012this\015\012 a quarter turn clockwise and then try the machine again. You may\015\012find that this hose twisted pulling the cleaner head up very slightly\015\012preventing it from contacting with your surfaces correctly.

2)Roller\015\012 brush-Roller brush not working or not rotating at proper speed.Your\015\012 roller brush must have been worn out or damaged or clogged with dust \015\012clean or replace it accordingly

3)Bottom plate (sole plate)\015\012 is installed wrong.If there is gap then the sucking will not \015\012take place properly.

4) cyclone component, needs to be cleaned \015\012properly.Run lukewarm water over the entire grid of small filtering \015\012holes.\015\012
5)Inspection ports at the back (U) shaped create \015\012blockages.

Note:Blockages mainly cause this problem.

This is the manual helps in a pictographic way about how to clean it.Page no 4 explains more clearly where to look for blockages.

Click here to download the manual.


Gasket has no issue with this..
Thank\015\012 you for using fixya.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We are having suction problems. ran over a chord and there is now no suction when we turn it on. last time we brought it in, they said something about a gasket??


Hi,\015\012 There could be various reasons why this could happen.I will tell \015\012you the reason's that could cause this problem and its solution.1)\015\012 Internal hose has twisted small cor ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi. I have a Kirby from back in the early 90s (model G3D). Never had major issues with it. Can't remember the last time I had maintenance/tune up done. It's just sounding different when I run it the last few times...almost like it's louder and kind of echo-ey. Still suctioning well, but something's not right and I don't want to run it until I know if anything's up. Any suggestions? I'd like to try and figure this one out on my own with your help. Thanks in advance for your help. Marci


Check the belt. this is a strong vaccume and even without the belt it will still have a decent amount of suction. If the belt is not tight or intact it can let the motor turn faster which will sound louder. other than that check all the hoses for hol ... Kirby Ultimate G Bagged Upright Vacuum

When I put the water tank on the unit it just starts draining out the bottom. It worked fine last time, so I don't know if some gasket or something is now missing?


Check the rubber "O" ring on the water tank and also the outlet valve they get stuck up? the "O" rings get hard and brittle ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Riccar 1700 will intermittently lose power while vacuuming. I have had the vacuum for 4 years and this is the second time that I have had this problem. The first time the authorized repairperson said the problem was a dirty hepa filter. The second time, the repairperson put on a "pig-tail"(?) and said that he did not have a shut-down problem when he tested the vacuum in the store. I just picked it up from the store today, brought it home and the same problem occurred within minutes.


... Riccar RC1100 Compact Vacuum

No suction My Hoover Wind Tunnel vacuum runs but there is no suction. The last two or three times I used it, it shut itself off after having a burning smell. When I unplug it for the suggested 30 minutes, the motor will run again but no suction. What is wrong?? Should I just buy a nve one? This one is 8 years old.


Sounds like your motor bearings are going bad. This is generally indicated by the motor overheating, and the heat transferring out through the motor pulley, which is where the belt attaches. So, your machine is overheating, melting the belt, and then ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Vacuum either stops for no reason and can't be restarted without unplugging and waiting 1/2 hour to restart, or it simply will not turn on at all. The red light comes on when the "On" button is pressed. I took it back today for the 4th time in a month to where it was purchased. They called later and said it was running fine and they could not detect a problem. The last three times they have (1) replaced the roller brush, (2) "unclogged" the vacuum, and (3) "adjusted" the belt.


This sounds like it might be an overheating problem. \015\012\015\012Some vacuum motors are fitted with thermal cut out fuses or thermistors which cut off the flow of electricity to the motor when the temperature gets to high. It is possi ... Lindhaus Activa 30-38 Bagged Upright Vacuum

When taking the handle/wand back to use it seems to lose the suction power regardless of what setting I use. Upon several times of standing it back up it seems to engage the suction power correctly is there a button or something that does not always engage to get power? can I fix it


When you say taking handle back I assume you mean the action to start rotation of brushes. Had simular problem and found by removing brush from tube and then cleaning "baked on rubbish" in plastic tube (so you can see clearly through tube) Clean with ... Dyson DC28 Animal Bagless Upright Vacuum

Good evening, I have a Xio Z1010 electrolux vaacum cleaner and I hope you'll be able to give me some advice. The vacuum cannot be started. Last time it started for a few seconds and stopped suddenly. Something similar happened long time ago but that was due to overheating. Once cooled down in few hours it would start again. It is not the case now after 24 hours. Could you give me any idea what could be the reason? Your help would be much appreciated. Adorian


... Electrolux Vacuums

I was cleaning my carpet using my hoover steamvac ls. I had already changed the water 3 times. The last time, the water ran out and I kept running it for a couple of minutes trying to **** up some of the water off the carpet when it just shut down. I check the breaker and the outlet and they were OK. Checked my manual for troubleshooting; couldn't find an answer there. Do you think I burned the motor up (I didn't smell anything) or will I have to send it in for repair? When I clicked on your web


(1) take the tank off and reassemble to assure you sealed to the lower handle.\015\012(2) the water feed has nothing to do with the motor or electrical, purely mechanical.\015\012Hoover web site is free, no cost. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My electrolux oxygen vacuum cleaner shut off and will not turn back on. It's less than a year old, but I bought it off Craig's list--they were the orginal owner and they said they bought it in May of 2008. I've only used it a few times and it worked fine except for the last time when it suddenly just shut off. I thought maybe it had come unplugged and I didn't really worry about it because I was finished vacuuming. But, I went to use it tonight and it would not turn on at all--no lights, nothing


No..Electrolux is really great about warranty service. They will help you even though you are not the original owner. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I brought an eureka model 2591av shapoo machine in 2004 I've only used the machine 4 times. now the it does not spray out the solution on the floor but it will **** up water, the vacuum part works. I took it to a repair shop, they said it was the pump that was broke and will cost $95.00 to fix. The purchase price of unit was only $129.00 My question to you is does that sounds like an honest or comparible diagnosis.please respond at ([email protected])


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=559297\015\012Generic problem for all Vacuums\015\012I brought an eureka model\015\012Posted by wadda08 on Apr 3 ... Vacuums

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t


Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

Our Winsdor Sensor XP12 does not show any power or lights, I did check the handle connection, it was fine. The power cord has been repaired with duct tape 3-4 x where someone has sucked up the cord, this may be the cause yet it ran fine last time it was used! so I am at a loss, please help if possible.08/31/2010 Steve


Any time the cord has been damaged badly enough to require taping, the possibility or intermittent "opens" exist. This means the wires are in contact much of the time, but will losed contact periodically. Even if it worked fine seconds ago, jigglin ... Windsor SR12 Sensor Bagged Upright Vacuum

We just bought it 20 days ago and used very few times. Today, when we were using it, it worked very well at the beginning. Suddenly, the vacuum malfunctioned. Although the motor ran, there is no suction at all.


Check to see if you have a clog in the hose ... Hoover Vacuums

My Fein won't turn on without rapping it on the floor ! I turn the switch on and it won't run until I tap or rap it and will shut off during operation. I'm sure there's something loose , but should I attempt it or take it back for repairs . Last time I tried it , it woudn't turn on at all . My wife purchased it earlier this year from a TV infomercial .


ELECTRIC FIELD (and all the push contacts are most of the time the problem the cause by this machines , dirt in the switch (the switch is made to disassemble to clean it sometimes .little screwdriver neccesary . ... Fein Multimaster Rs - Msxe 636 - 2 Rs

The Petmate powerhead roller stopped rotating. I checked for anything binding it - nothing. There is power getting to it, just no rotation. As the guy said in the post above, it's like it is locked into the plastic housing, although it just worked last time I used the powerhead. Help!


... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Hi I own a Bissell Proheat Powersteamer pro-tech with a turbobrush. I have been using "bissell multi-allergen removal formula for carpets and upholstery." I ran out of that last night. Today I went to walmart looking for more. Everything I found said "2x Ultra Concentrated Bissell multi-allergen." I'm confused on where to add the cleaner. I have a water tank and a separate soap tank. The instructions on this new cleaner bottle say to add 4 capfuls for the formula tank and dilute with hot tap wat


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Last time I used my Bissell Pet Hair Remover vacuum it smelled like something was burning and it left a black mark on the carpet. What should I do?


When you smell burning like that it usually indicates that the belt is worn and slipping on the motor shaft. You probably need to change the belt. You can get the belts for your model here: ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat


It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

My Bissell Proheat has stopped suctioning the water solution. It has worked well in the past, but the last time I used it the recovery bladder had just a small amount in it. Could it be stopped up?


I have this machine too. IF the soap dispenser does not have anything (even water) in it the water sprayer will not spray. Sometimes the water valve from the tank has an air bubble in it. Remove the tank and push up the valve. A little water will fal ... Vacuums

Our Bissell Cleanview II 3576M does a great job except that the filter cup below the dirt cup gets full very fast and the dirt cup barely has anything in it. To clean the whole house, I have to empty the dirt cup and clean the filter several times. It didn't use to work this way. It seems like something is missing, a gasket or seal maybe? I don't think dirt, hair and debris should be going straight to the lower cup and bypassing the upper. I looked at the user guide but can't see why it's happen


Contact Bissell Direct for a parts diagram and support at \015\012\015\012http://uk.bissell.com/EmailUs.aspx\015\012 ... Bissell 3576 CleanView II Bagless Upright Vacuum

It has no suction...last couple of times while using the vacuum it would cut itself off. If I tried to use it the next day it would do the same thing


Hi,\015\012You vacuum is probably plugged up. Flip it over, beater bar up, and remove the plate that surrounds the beater bar. The beater bar needs to come out next. If the belt is good, it will be a little hard to remove. The beater bar si ... Vacuums

I take apart and clean my DC17 every 2 weeks. When I put it back together it always works perfect. This last time, I noticed that the self propel is not working...am I missing something? I took it apart to be sure eveything is in it's place but no difference. Now I have to push really hard.Any suggestions?


The roller is not spinning do to motor or belt not working. If it is the motor then the machine will have to go back to dyson if it is the belt then that is an easy replacement. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Steamvac The last several times that I have used the steam vac to clean the carpet, I've noticed that the solution is not coming out as a spray. Instead it is a steam. Is this normal or is something wrong? Thanks for your help..


You might try running a solution of vinegar and water thru it to clean out the lines and spray nozzles. Also are the brushes turning when you are using it, that could also be the problem. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I HAVE A FANTOM VACUUM CLEANER MOD.#F1205400. I PURCHASED IT ABOUT 6 OR SO YEARS AGO.IT WORKS PERFECT,AS FAR AS SUCTION, THE ONLY PROBLEM IS ABOUT 2 MONTHS AGO,SOMETHING HAPPENED TO IT AND IT GOT VERY LOUD, KIND OF LIKE A CAR WITHOUT MUFFLER. I TOOK IT APART,AND FOUND NOTHING OBVIOUS. CAN YOU GIVE ME SOME IDEA OF WHAT I CAN CHECK TO RESOLVE THIS PROBLEM. AS I SAID BEFORE IT STILL VACUUMS GREAT. THANK YOU, VINCE


You probably have a bad motor bearing. I don't know if the motor is available now or, these older Fantom's are obsolete along with most of their parts. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0727 seconds